Arun Agro Coal Dhar, Madhya Pradesh

We are reckoned as Biomass Briquettes Manufacturer and Supplier based in Madhya Pradesh, India. We manufacture the Biomass Briquettes in our �Biomass Briquetting Plant� under the strict supervision of the experts. It is a process to convert Agro waste, Forestry waste and Industrial waste into biomass Briquettes / Bio-coal. Briquettes are formed in cylindrical logs using high mechanical pressure without the use of chemical or binder. Benefits Of Biomass Briquettes : Briquettes are ready substitute of Coal/wood in industrial boiler and brick kiln for thermal application The Biomass Briquetting is the best renewable energy for healthy environment and economy Bio Coal briquettes are Non conventional Source of energy, non polluting and economical It is a completely Eco-friendly green energy project Easy to burn - lower ignition temperature compared to coal Smokeless burning and sustained combustion and the temperature requirement is achieved due to very efficient combustion. Leaves only white ash without any fixed carbon Full heat value is utilized. Easy to handle and 1000 kgs of briquettes per cubic meter can be stored and transported against 50 kgs of agro-waste. No pollution to the environment and no toxic gas and sulphur emission and even no odor. Very low ash content as low as 2 to 5% compared to 30 to 49% in coal. No binder is used so it is 100 % natural. The natural polymer lignin acts as a binder and provides mechanical support and also provides resistance to decay and repels water Very well suited to gasifier which can run any engine because of the combustion efficiency and solid form In gasifiers, the briquettes can be used and the partially pyrolysed briquettes can be again used as a substitute for high value added charcoal for domestic and industrial use leaving the fuel wood unutilized and thus avoiding deforestation A typical usage of briquettes made out of paper mill sludge mixed with iron sludge power is made in big furnaces to keep the temperature alive for easy start up. Saves the environment from pollution, all conventional fuel pollutes the atmosphere Bio Coal Replaces : Diesel Kerosene Furnace Oil Firewood Coal Lignite Application Areas Of Bio Coal Briquettes : Ceramic and refectory industry Solvent extraction plant Chemical units Dyeing plant Milk plant Food processing industry Vegetable plants Spinning mill Lamination industry Leather industry Brick making units Textile unit

We are offering clc blocks clc is an air-cured lightweight concrete that can be produced at project site, utilizing equipment and molds normally in use for conventional concrete. The density recommended is 1.000 kg /m³ (oven-dried) for blocks and 1.200 kg/m³ to produce prefab elements and walls cast in-situ. The typical mix for a 1.000 kg/m³ density clc to be used in blocks is as follows (to produce 1 m³) cement (portland): 190 kg = 61 liters fly-ash: 740 kg = 265 liters (approx) water: 250 kg = 250 liters foam (neopor-600): 423 liters wet density 1.179 kg/m³ total volume (submerged in water) 1.000 liters (= 1 m³) expected (oven-dry) density. Approx. 1.000 kg/m³ content of air in concrete approx. 43% content of fly-ash in solid material (929 kg): 33% content of fly-ash in oven-dry material: 31 % benefits of clc blocks/element tremendous weight reduction high thermal insulation optimum fire rating substantial material savings no gravel used.  little cement  less steel in structure and foundation  easy and fast production no primary energy and reduced transportation costs boon for remote areas with only sand available clc, like conventional concrete ages well, increasing its strength by as much as 50% (!) between 28 and 90 days after pouring, as long as clc draws humidity from the atmosphere it will keep on increasing its mechanical properties. Popular block sizes are: 600x200x200/100mm 500x250x200/100mm 500x400x100mm or as desire blocks are cast in vertical position to offer equally accurate sides, given by the mold. Only one side (the top when cast) is not given by the mold as open-top, which is screeded. This side will face the next block in masonary anyhow. aspect brick wall clc wall remarks thickness external 230 mm 200/150 mm saving of 13 to 35% partition 115 mm 100 mm saving of 13% mortar masonry external 0.051 m³/m² 0.011 m³/m² saving of 78% partition 0.02 m³/m² 0.005 m³/m² saving of 75% plastering 12 + 15 mm 8 + 10 mm saving of 33% dead load external 601 kg / m² 256 / 206 kg / m² reduction of 60% partition 319 kg / m² 148 kg / m² reduction of 48% labour for work 100% 60% reduction of 40% quality normal superior satisfied client ease of working chase cutting difficult easy faster laying service driving nail difficult easy happy client longevity may deteriorate with time gains strenth with times as ordinary concrete better durability

We provide industrial consultants. we are here to consult those persons who want to establish her industry. We will provide all types of legal n machinery related information and advices. We are working on this area in last two year.