Our Products
We are offering two roll rubber mixing mill. Two roll rubber mixing mill main uses are following in rubber product factory: natural rubber refining, raw rubber and compound mixing. Rubber beating mixing and rubber tab letting. This machine is double roller opening to be used for rubber mixing. It consists of seat, frame, rubber, driving device, lubricator and cooler, range adjusting device of roller. Safety brake. Motor and reducer, etc. The roller is made from safety cooled and hard cast steel, smooth surface is polished in term of different case. Saturated steam and cooling water can be inputted in the empty roller to adjust speed of roller. Colloidal particles are drawn into the gap of the two rollers which make relative rotation in different velocity to mix rubber.
We are offering tyre curing press. Tyre curing press is used to vulcanize outer tyre and tyre flap as well as other rubber products.
Roller diameter (mm) | 550 | 660 | |
Working Length of the roller(mm) | 1500 | 2130 | |
Working Linear speed of front roll (m/min) | 27.94 | 28.1 | |
Friction Ratio of front and rear roll (m/min) | 11.22 | 11.24 | |
Max Gap(mm) | 15 | 15 | |
Capacity per batch (kg) | 50-60 | 165 | |
Driving motor power ( Kw ) | 110 | 245 | |
Overall dimension (mm) | L | 5900 | 7465 |
W | 2680 | 3662 | |
H | 2080 | 2750 | |
Weight (kg) | 27000 | 6500 | |
Note: | Bearing | ||
Rubber sheeting millis mainly used for figuring of the crude, the mixing of the rubber, the remixing rubber and pressing to sheets etc.
Model | XJL-150 | XJL-200 | XJL-250 |
Screw Dia.(mm) | 150 | 200 | 250 |
Screw speed(r/min) | 41.6 | 44 | 40 |
L/D ratio | 5.24 | 5 | 4.8 |
Cutting equipment speed(r/min) | 17 | 16 | 6 |
Motor power(KW) | 45 | 75 | 110 |
Steam pressure(MPa) | 0.6-0.8 | 0.6-0.8 | 0.6-0.8 |
Cooling water pressure(MPa) | 0.2 | 0.2 | 0.2 |
Capacity(kg/h) | 400 | 800 | 1200 |
Overall dimensions(mm) | 35858141470 | 460018001800 | 495018001483 |
Weight(kg) | 5000 | 8000 | 9000 |
Type | XLB-DQ120012002 | XLB-DQ130020001 | XLB-Q120025001 | XLB-Q150020001 | XLB-Q200030001 | XLB-Q140057001 |
Total pressure(MN) | 315t | 560t | 750t | 1000t | 1800t | 2800t |
Platen size(mm) | 12001200 | 13002000 | 12002500 | 15002000 | 20003000 | 14005700 |
Daylight (mm) | 200 | 400 | 400 | 400 | 400 | 400 |
No of Daylights | 2 | 1 | 1 | 1 | 1 | 1 |
Piston stroke(mm) | 400 | 400 | 400 | 400 | 400 | 400 |
Plate Unit Area pressure(Kg/cm2) | 22 | 21.5 | 25 | 33.5 | 30 | 35 |
Main motor power(KW) | 3 | 8 | 9.5 | 11 | 26 | 43.5 |
Overall dimension(LWH)(mm) | 168513202450 | 200018602500 | 256017002780 | 281015503325 | 290032002860 | 240058003600 |
Weight(kg) | 9500 | 17000 | 20000 | 24000 | 66000 | 110000 |
Plate vulcanizing pressapplies to vulcanizing various kinds of rubber and plastic model products as well as non-model products.
The machine is in frame structure with below pressing form (upwards). Under the working hydraulic pressure, the embolism ascends to make hot plate close for getting pressure, while the embolism descends (namely hot plate turning on) by deadweight of hot plate, platform and embolism to drive working fluid to fuel reserve tank to achieve the aim of descending (namely turning on).
|
type | xlb-dq350x350x2 | xlb-dq400x400x2 | xlb-dq600x600x2 | xlb-dq750x850x2(4) |
total pressure(mn) | 0.25 | 0.50 | 1.00 | 1.60 |
plate size(mm) | 350x350 | 400x400 | 600x600 | 750x850 |
daylight(mm) | 125 | 125 | 125 | 125 |
daylight no | 2 | 2 | 2 | 2(4) |
piston stroke(mm) | 250 | 250 | 250 | 250(500) |
unit areapressure(kg/cm2) | 20 | 31 | 28 | 25 |
main motor power(kw) | 2.2 | 2.2 | 2.2 | 3 |
overall dimension(mm) | 1300x800x1500 | 2400x550x1500 | 1401x680x1750 | 1900x950x2028 |
weight(kg) | 1150 | 1300 | 3500 | 6500(7500) |
hydraulicvulcanizing machineis used for all kinds of vulcanizing mould, rubber and plastic mould products, and non-mould products.
being a column structure and downward pressing type, the heating plate opens by the self-weight of the heating plate, platform and plunger. The rising of the plunger makes the heating plate close while the hydraulic oil provides the pressure.
Precured Tread Hydraulic Pressis used to produce strip precured tread for renovation of all kinds of tires. And it is suitable for cold renovation procedure of tires. We can design and produce it according to customers request.
Tyre shaping vulcanizing machinehave vertical lift tilting and sliding two different open and close mould methods. It is consist of four big parts: mechanism section, lubricating system, pipeline system and electrical control system. It is the ideal equipment for manufacturing the radial tyre or nylon ply bias tyre.
TYPE | 45" | 55" | 63.5" | 65" |
Quantities of mold | 2 | 2 | 2 | 2 |
Inside diameter of shield(mm) | 1145 | 1310 | 1525 | 1560 |
Max.clamping force per cavity(KN) | 1600X2 | 2950X2 | 4220X2 | 4300X2 |
Height of mold (mm) | 190-430 | 245-445 | 254-635 | 254-635 |
Bead size (in) | 12-18 | 16-20 | 16-24 | 16-24 |
Main motor power(mm) | 11 | 13 | 13 | 16 |
Weight (ton) | 32 | 48 | 60 | 63 |
Delhi, India 
