Other Products / Services #3408042

A gas train consists of Filter, Slam-shut off valve, pressure regulator, safety relief valve & flame arrestor. Filter helps to remove the dust / dirt particles in the gas which may damage the regulator parts. The slam shut off valve normally remains open. Incase the outlet pressure of the regulator exceeds the permissible limits, the slam shut off valve senses it through the impulse line & instantly shuts off the supply to the downstream system. The safety relief valve is provided for additional safety. It is to be set at higher pressure than the slam shut off valve pressure so that the safety relief valve will operate only when slam shut off valve fails to operate. The outlet of the safety relief valve is vented well above the roof.

A well known Pressure Switch supplying company.

We are the main supplier of this product.

We are offering Burner Motor

An impeller is a rotating component of a centrifugal pump, usually made of iron, steel, bronze, brass, or aluminium, which transfers energy from the motor that drives the pump to the fluid being pumped by accelerating the fluid outwards from the center of rotation. The velocity achieved by the impeller transfers into pressure when the outward movement of the fluid is confined by the pump casing. Impellers are usually short cylinders with an open inlet (called an eye) to accept incoming fluid, vanes to push the fluid radially, and a splined, keyed or threaded bore to accept a drive-shaft.

The impeller made out of cast material in many cases may be called rotor, also. It is cheaper to cast the radial impeller right in the support it is fitted on, which is put in motion by the gearbox from an electric motor, combustion engine or by steam driven turbine. The rotor usually names both the spindle and the impeller when they are mounted by bolts.

ECCS Burners offers wide range of burner sequence controllers which are preprogrammed to ensure the automatic working of gas/oil burners. They assist in managing safe start up of the burner and continuously monitor of the flame. These systems provide output for blower, ignition, solenoid valves etc. with prefixed timings for continuous flame supervision.

The simplest type of electric ignition is the high tension system, which usually takes the form of a mains transformer supplying some 10K volts to a pair of insulated electrodes placed to form a spark gap adjacent to the burner nozzle. The resultant spark acroos the gap is sufficient to ignite distillate medium fuel oils and most gas installations. In some installations a single elctrode may be mounted to utilize a part of the burner casing (or a special projection from it) to complete the circuit.

We design ignition elements and monitoring electrodes according to your requirements.

Temperature Controllers, used in wide variety of industries, is the starting and important tools for the controlling of the temperature to get desired results in various industries. Autonics' Analog/Digital(PID) temperature controllers, offer quick setup and provide precise temperature management and control for a variety of applications while offering the better price, design and easy operation. They will be the definite choice for your successful control in any temperature applications.

industrial auto ignition transformers are used in a wide variety of commercial and industrial heating applications. Their uses include commercial heat treating installations, bakeries, grain dryers, and industrial ovens.

Our Oil Pumping and Heating Units are designed to supply fuel oil at pre-determined constant pressure and temperature to ensure efficient combustion. These compact and fully assembled units with all valves, thermostats, pressure gages, pressure switches etc on its own drip tray prevent undesirable variations in temperature caused by heat loss and varying rates of oil flow in long oil lines from heaters located far away. The PH units circulate oil in the ring main at three times of the consumption to provide a stable oil supply system for best combustion results.

we are leading best burner pump supplying company.

We are the main supplier of this product.

These UV sensor are installed for controlling burner and avoiding any accidental satiation caused by burner. They are used extensively in industrial manufacturing.

Our oil pumping and heating units are designed to supply fuel oil at pre-determined constant pressure and temperature to ensure efficient combustion. These compact and fully assembled units with all valves, thermostats, pressure gages, pressure switches etc on its own drip tray prevent undesirable variations in temperature caused by heat loss and varying rates of oil flow in long oil lines from heaters located far away. The ph units circulate oil in the ring main at three times of the consumption to provide a stable oil supply system for best combustion results.

Our oil pumping and heating units are designed to supply fuel oil at pre-determined constant pressure and temperature to ensure efficient combustion. These compact and fully assembled units with all valves, thermostats, pressure gages, pressure switches etc on its own drip tray prevent undesirable variations in temperature caused by heat loss and varying rates of oil flow in long oil lines from heaters located far away. The ph units circulate oil in the ring main at three times of the consumption to provide a stable oil supply system for best combustion results.

A gas train consists of filter, slam-shut off valve, pressure regulator, safety relief valve & flame arrestor. Filter helps to remove the dust dirt particles in the gas which may damage the regulator parts. The slam shut off valve normally remains open. Incase the outlet pressure of the regulator exceeds the permissible limits, the slam shut off valve senses it through the impulse line & instantly shuts off the supply to the downstream system. The safety relief valve is provided for additional safety. It is to be set at higher pressure than the slam shut off valve pressure so that the safety relief valve will operate only when slam shut off valve fails to operate. The outlet of the safety relief valve is vented well above the roof.

ECCS Burners offers wide range of burner sequence controllers which are preprogrammed to ensure the automatic working of gasoil burners. They assist in managing safe start up of the burner and continuously monitor of the flame. These systems provide output for blower, ignition, solenoid valves etc. with prefixed timings for continuous flame supervision.

These uv sensor are installed for controlling burner and avoiding any accidental satiation caused by burner. They are used extensively in industrial manufacturing.

We are offering best Solenoid Valves supplying company.

We are leading best Gas Regulators supplying company.

Temperature Controllers, used in wide variety of industries, is the starting and important tools for the controlling of the temperature to get desired results in various industries. Autonics' AnalogDigital(PID) temperature controllers, offer quick setup and provide precise temperature management and control for a variety of applications while offering the better price, design and easy operation. They will be the definite choice for your successful control in any temperature applications.