SUCO Silicon-on-Sapphire (SOS) pressure transmitters/transducers – hot new development offering satisfying high temperature operation, high accuracy and repeatability, and long term stability requirements in off highway equipment. The ability to operate at high temperatures, chemical inertness, and virtual absence of hysteresis make the strain gauges ideal for use in pressure sensors. However, pressure transducers used in hydraulic systems of off-highway machines must tolerate punishing conditions, such as severe pressure spikes caused by valves shifting, prolonged exposure to continual pulsation, broad temperature ranges, heavy shock, and vibration. Pressure spikes can be especially harmful or even destroy a pressure transducer. Prolonged exposure to continual pulsation can cause fatigue failure of the pressure transducer and influence long term stability and accuracy. The benefits of SOS sensor technology would make them ideal for off-highway equipment. However, price sensitivity has k ept them from penetrating the high-volume off-highway equipment industry. Hence SUCO has introduce its Type 07XX pressure transducer based on silicon-on-sapphire technology. Key advantages of the transducer include: Silicon-on-Sapphire technology Body and wetted parts made of stainless steel / titanium No seals and thus low leakeage rate even with difficult gases High overpressure safety especially suitable for use in hydraulic applications Long working life even with high rates of pressure cycles High accuracy and reliability for secure process monitoring Very small size for compact subassemblies Technical data: Type: 0705, 0710, 0720 Output signal: 0, 5-4, 5 V ratiometric (Type 0705) 0-10 V (3-wire) (Type 0710) 4-20 mA (2-wire) (Type 0720) Supply voltage Ub: 5 VDC +/- 10% max. 6, 5 VDC (Type 0705) 12-32 VDC (Type 0710) 10-32 VDC (Type 0720) Maximum load: >= 4, 7 kΩ (Type 0705 & 0710)

Try out and switch to SUCO hex 27 – one of the most demanded pressure switches of SUCO, if you are looking for: High-quality micro-switch for reliable switching Easy adjustable switching point - even during operation Adjustable hysteresis Self-cleaning contacts for a long working life (only 250V versions) High overpressure safety Long working life under harsh operating conditions Connector plug or protective cap to protect against moisture and dirt, and thus easy replacement on site by service personnel Various thread connections available to suit your installation A choice of zinc-plated steel or stainless steel as body material and a selection of diaphragm materials ensure high resistance to media Technical data: Degree of protection: IP65 with suitable connector installed, Terminals IP00 Switching frequency: 200/min Temperature stability for diaphragm/seal materials: NBR -30°C to +100°C EPDM -30°C to +120°C FKM -5°C to +120°C Silicone -40°C to +120°C HNBR -30°C to +120°C Mechanical life expectancy:10^6 cycles (life expectancy of diaphragm pressure switches only for pressures up to maximum 50 bar) Maximum pressure rate: 1 bar/msec Vibration resistance: 10g / 5-200 Hz sine-wave Shock resistance: 294 m/s²; 14 ms half-sine-wave Hysteresis: adjustable 10–30% (only at works); type 0140/0141 not adjustable, standard value approx. 10–20%.

Try out and start application of SUCO pressure switches 30 A/F: Panel or manifold mounting for clear, maintenance-friendly installation Easily adjustable by user High-quality micro-switch for reliable switching High overpressure safety Connection plug for simple installation on site Technical data: Degree of protection: IP65 valve connector fitted Switching frequency: 200/min Temperature stability for diaphragm/seal materials: NBR -30°C to +100°C EPDM -30°C to +120°C FKM -5°C to +120°C Mechanical life expectancy: 10^6 cycles (at pressures up to 50 bar) Vibration resistance: 10g / 5-200 Hz sine-wave Shock resistance: 294 m/s²; 14 ms half-sine-wave Body material: AlMgSi1 F28 Hysteresis: Type 0159: 10-30% (not adjustable) Type 0161/0162/0175: 10-30% (adjustable at works).

A hot new development from ESI Technologies, UK! Accurate pressure measurement in high temperature environments is important in many applications and can often present a challenge. With this in mind, the HI2200 – a rugged, high temperature pressure transducer, is designed to operate in demanding environments with outstanding durability and long-term stability. It is constructed from components carefully selected to operate reliably at elevated temperatures. It is available in pressure ranges from 0-1bar to 0-1500bar with un-rationalised mV output with temperature compensated options. It has titanium alloy wetted parts, a stainless steel and titanium housing. It is suitable for use at operating temperatures of up to 200°C. It can not only be used to measure high temperature media, but can also be used in applications where the ambient temperature can also reach 200°C. But the real beauty of this product is that it is equipped with state of the art silicon-on sapphire technology, which offers performance previously unobtainable or prohibitively expensive. Whether it’s specific application, design or supply expectations – solution combining the latest technology, reasonable cost and no compromise on quality, is just a call away!

SUCO has enhanced its product portfolio with a new series of pressure switches with fully integrated connector varieties. Until now, SUCO has already offered a membrane/piston pressure switch with an integrated bayonet connector (DIN 72585) known as type 0120/0121. This product range is now expanded with the addition of double-pole and triple-pole Deutsch-Connectors, AMP Superseal, AMP Junior Timer, Packard Metri Pack and M12 connector. SUCO also offers the counterparts to these connectors with a standardised cable length of 2 meters. The usage of these kinds of pressure switches will considerably reduce assembly time, since the connection can be activated by a simple turning movement or by fastening the components together and latching them afterwards. The basis of these “integrated pressure switches” are the million times proved mechanical pressure switch types 0166 and 0163 (for technical specifications see www.suco.de), in which the higher sealing protection of the IP 67 standard (depending on connector) can be guaranteed.

Try out and start application of SUCO ready-wired switches – solution for those who wish to fulfill commercial vehicles, mobile hydraulics, and similar applications where degree of protection IP67 or IP6K9K may be required. At SUCO any commercially-available connector system can be supplied ready-wired with a customer-specific cable length. This ensures great flexibility, and we can also supply small quantities without the need for expensive tooling. The technical data of ready-wired pressure switch variants are substantially the same as those of the standard models. Differences in the technical data will be agreed with the customer and defined on a customer-specific drawing of the ready-wired pressure switch. Select from the wide range of plugs: Plugs to DIN 72585, AMP Junior-Timer, Cannon plugs, AMP Superseal, Packard plugs (Weather Pack), Packard plugs (Weather Pack), Deutsch plugs (DT 06), Deutsch plugs (DT 04 - 2P), Deutsch plugs (DT 04 - 3P).

Try out and start application of SUCO vacuum pressure switches: Low-cost switch with high SUCO standard of quality Switching point easy to adjust High overpressure resistance and long working life even under harsh operating conditions Model 0150 with micro-switch for reliable switching Model 0150 with panel-mounting feature Model 0151 as normally open or normally closed Technical data: Type: 0150, 0151 Degree of protection: IP65 Max. Voltage: 250 V (Type 0150) 42 V (Type 0151) Switching frequency: 200/min Temperature stability: -20°C - +100°C (Type 0150) -20°C - +120°C (Type 0151) Body material: AlMgSi1 F28 (Type 0150) Brass (Type 0151) Mechanical life expectancy:10^6 cycles (at pressures up to maximum 20 bar) Vibration resistance: 10g / 5-200 Hz sine-wave Shock resistance: 294 m/s²; 14 ms half-sine-wave.

SUCO has enhanced its product portfolio with a new series of pressure switches with fully integrated connector varieties. Until now, SUCO has already offered a membrane/piston pressure switch with an integrated bayonet connector (DIN 72585) known as type 0120/0121. This product range is now expanded with the addition of double-pole and triple-pole Deutsch-Connectors, AMP Superseal, AMP Junior Timer, Packard Metri Pack and M12 connector. SUCO also offers the counterparts to these connectors with a standardised cable length of 2 meters. The usage of these kinds of pressure switches will considerably reduce assembly time, since the connection can be activated by a simple turning movement or by fastening the components together and latching them afterwards. The basis of these “integrated pressure switches” are the million times proved mechanical pressure switch types 0166 and 0163 (for technical specifications see www.suco.de), in which the higher sealing protection of the IP 67 standard (depending on connector) can be guaranteed.

A hot new development from ESI Technologies, UK! Accurate pressure measurement in high temperature environments is important in many applications and can often present a challenge. With this in mind, the HI2200 – a rugged, high temperature pressure transducer, is designed to operate in demanding environments with outstanding durability and long-term stability. It is constructed from components carefully selected to operate reliably at elevated temperatures. It is available in pressure ranges from 0-1bar to 0-1500bar with un-rationalised mV output with temperature compensated options. It has titanium alloy wetted parts, a stainless steel and titanium housing. It is suitable for use at operating temperatures of up to 200°C. It can not only be used to measure high temperature media, but can also be used in applications where the ambient temperature can also reach 200°C. But the real beauty of this product is that it is equipped with state of the art silicon-on sapphire technology, which offers performance previously unobtainable or prohibitively expensive. Whether it’s specific application, design or supply expectations – solution combining the latest technology, reasonable cost and no compromise on quality, is just a call away!

Try out and switch to SUCO hex 27 – one of the most demanded pressure switches of SUCO, if you are looking for: High-quality micro-switch for reliable switching Easy adjustable switching point - even during operation Adjustable hysteresis Self-cleaning contacts for a long working life (only 250V versions) High overpressure safety Long working life under harsh operating conditions Connector plug or protective cap to protect against moisture and dirt, and thus easy replacement on site by service personnel Various thread connections available to suit your installation A choice of zinc-plated steel or stainless steel as body material and a selection of diaphragm materials ensure high resistance to media Technical data: Degree of protection: IP65 with suitable connector installed, Terminals IP00 Switching frequency: 200/min Temperature stability for diaphragm/seal materials: NBR -30°C to +100°C EPDM -30°C to +120°C FKM -5°C to +120°C Silicone -40°C to +120°C HNBR -30°C to +120°C Mechanical life expectancy:10^6 cycles (life expectancy of diaphragm pressure switches only for pressures up to maximum 50 bar) Maximum pressure rate: 1 bar/msec Vibration resistance: 10g / 5-200 Hz sine-wave Shock resistance: 294 m/s²; 14 ms half-sine-wave Hysteresis: adjustable 10–30% (only at works); type 0140/0141 not adjustable, standard value approx. 10–20%.

Try out and switch to SUCO hex 24 – one of the most demanded pressure switches of SUCO, if you are looking for: Low-cost mechanical pressure switch to high SUCO quality standards Normally closed or normally open compact switch Switching power 100VA High overpressure resistance (up to 35, 300 and 600 bar) Long working life even under harsh operating conditions Easily adjustable switching point - even during operation Various thread connections to suit your installation (request data sheet) Ready-wired variants Versions with push-on and screw terminals With gold contacts on request Zinc-plated steel, Brass and other body materials Integrated DIN 72585 connector (type 0120/0121) Technical data: Degree of protection: IP65 (IP67/IP6K9K for 0120 /0121) Terminals IP00 Switching frequency: 200/min Temperature stability for diaphragm/seal materials: NBR -30°C to +100°C EPDM -30°C to +120°C FKM -5°C to +120°C Silicone -40°C to +120°C HNBR -30°C to +120°C Mechanical life expectancy: 10^6 cycles (at pressures up to 50 bar) Maximum pressure rate: 1 bar/msec Current rating (resistive): ≤ 4 A Vibration resistance: 10g / 5-200 Hz sine-wave Shock resistance: 294 m/s²; 14 ms half-sine-wave Type 0163 Material Carbon Steel, Over Pressure Safe Up to: 600bar 0164 Material Stainless Steel, Over Pressure Safe Up to: 600bar 0166 Material Carbon Steel, Over Pressure Safe Up to: 300bar 0167 Material Brass, Over Pressure Safe Up to: 35bar 0168 Material Carbon Steel, Over Pressure Safe Up to: 300bar 0169 Material Carbon Steel, Over Pressure Safe Up to: 600bar.