This Basket is manufacturing from spring steel bow fitted with Canvas/Rubber. Canvas is fitted in side of bow with overlapping. This type of Basket is Slip on type & easily installed by sliding it over the pipe and of casing joints. Baskets are available in wide range of casing size (4-1/2" to 20") to hole sizes and it self-centering due to its sturdy spring steel bows. Design is as such Basket have minimizes interference against casing for assisting pipe rotation and reciprocation.

The LAXMI Snap Sucker Rod wrench is made of high grade forged alloy steel and hardened to resist wear. The light weight rugged tool is excellent for manual makeup and break out of Sucker Rod joints. It features a counter balanced grip to reduce fatigue. The cross section of the handle is oval which provides a natural resistance to the wrench spinning when gripped. The head is spring loaded and a hardened steel bushing is provided between the wrench head and handle. Laxmi Snap Sucker Rod range are available for sucker rods of sizes 5/8", 3/4" 7/8, 1" & 1.1/8”.

LAXMI Double Packing Stuffing Box are manufactured as per API 11B standard. Stuffing Box is good for in intermittent flow condition using split cone nitrile rubber high temperature packing (primary packing 3 pieces top, 1 piece bottom and blow out control system packing 2 pieces top, 1 piece bottom) rated at 250º F continuous service. Metallic compression plate and bolt type blow out control system. Const. Of split cone packing and metallic plate arrangement such that primary packing can be changed by tightening compression bolts so this double packing to prevent leakage and will permit packing change under pressure. Bottom connection available in 2.7/8” and 3.1/2” tubing size to accommodate Polish Rod of 1' through 1.3/4”. Upper and lower gland are self aligning. Height above tee is 15” and working pressure is upto 2500 PSI.

Our DI Hard Liners combines the strength of a forged steel outer shell with corrosion and abrasion resistance of inner High Crome Iron sleeve. These High Crome Iron sleeve is precision honed with a surface finish designed to ensure maximum piston life and heat treated to a minimum uniform bore hardness of 63 HRC. DI Hard Liners are available in various sizes to fit in mud pumps widely used by drillers today. These liners are made for superior performance under tough corrosive and abrasive conditions. Rigid inspection is conducted on each of the Liners for uniformity of hardness, finish and accuracy in all dimensions. Features, Advantages & Benefits   Inner high chroma iron sleeve is precision honed to ensure maximum piston life.   Use of high quality material and modern machining methods makes it rigid tough and durable.

LAXMI Polished Rods are manufactured as per latest edition of the API Specification 11B. All rods are manufacture from cold drawn, Carbon Steel, Alloy Steel and Stainless Steel. All rods are Machined, Ground and Cold Rolled Threads. Cold Rolling will increase fatigue life of threads and also compress the root of threads which increase tensile loading in threads Laxmi manufacture four type of Polished Rod.

LAXMI Casing Scraper is used to remove scale, cement sheath mud cake, rust, scate, perforation burrs and other substances from the inside wall of casing. Casing Scraper is manufactured from forged heat treated alloy steel. The Scraper blades fit into machined recesses & are held by stopper & spacer. The Scraper Blade feature left hand helical grooves and are hardfaced for maximum service. There are sufficient blades in the body to completely scrape the entire 360º inside respective casing to achieve clean casing bore by reciprocation and or rotation. Scraper to be installed in the drilling string between the bit and the bit sub. The bit is run below the scraper to serve as a guide and prevent plugging the circulation hole through the scraper. Laxmi Scraper such design that the scraper shall neither get damaged nor stuck down hole. Features, Advantages & Benefits   Rugged one piece Alloy Steel Body   Full 360º coverage of Casing I.D. by six blades   Large By-pass area around and between the blades for circulation   Blades are individually locked into the scraper body for case of repair   Blade retainer blocks are designed so that all thrust and rotational load are carried by the scraper body and not be the retaining screws.   Scraper have an API Reg Box down for installation Drill

The Polished Rod Clamp is used to support the rod string while the weight is being carried by the bridle and carrier bar. There Clamps are available with one bolt or two bolt types. Clamp body is made from a high tensile heat treated AISI 1040 Forged Steel and is designed and machined to provide greater holding power. AISI 4140 Alloy steel hinge pins are heat treated for greater strength and easy opening. The bolts, nuts and washers are made from high tensile heat treated steel and are cadmium plated for maximum corrosion resistance. The clamping surface is bored and reammed to exact polished rod size for better clamping at 90 degree to the polished hole. “Laxmi Police Rod Clamps” are manufactured in sizes 1.1/8”, 1.1/4” & 1.1/2” with both double bolt and Single bolt design clamp.

All crossover sub, basket subs, lift plug and lift sub are manufacturing from ultrasonically tested 4145 H modified alloy steel. These are fully heat treated to a Brinell hardness range of 285-341 and have an Izod impact strength of 40 Ft/lb minimum. The substitutes are made in all size as per requirement of customers. All Connections are machined and finished according to API standards, thread roof are Cold rolled & Connections are phosphatized. Ordering Information : To order, rotary subs, please specify, On all subs   Identify sub type or use. (Example: Kelly saver, crossover, or bit sub, etc.)   Overall length *   Bore diameter.   Size and type of type of upper and lower connections, indicating pin or box and special joint features (i.e. stress relief grooves, bore back, low torque faces)   Any special requirements (i.e. float bore).

LAXMI Double Packing Stuffing Box are manufactured as per API 11B standard. Stuffing Box is good for in intermittent flow condition using split cone nitrile rubber high temperature packing (primary packing 3 pieces top, 1 piece bottom and blow out control system packing 2 pieces top, 1 piece bottom) rated at 250º F continuous service. Metallic compression plate and bolt type blow out control system. Const. Of split cone packing and metallic plate arrangement such that primary packing can be changed by tightening compression bolts so this double packing to prevent leakage and will permit packing change under pressure. Bottom connection available in 2.7/8” and 3.1/2” tubing size to accommodate Polish Rod of 1' through 1.3/4”. Upper and lower gland are self aligning. Height above tee is 15” and working pressure is upto 2500 PSI.

Basket Petals are manufactured from high strength spring steel, which allows for strength and flexibility to support long columns of cement during primary cementing operation. The Cement Basket petals are arranged in an over lapping position that allows for maximum fluid passage from below while allowing for retention of the above fluids through the entire operating range of the Cement Basket. Baskets are hinge type so easily install on casing pipe.