Coupling fittings are used for fluid conduits in which each end portion of two tubes to be connected is provided with a swaged-on adapter carrying the necessary means to connect or disconnect the tubes without disturbing the swaged-on adapter. Our range of coupling fittings are available in aluminium, steel and bronze. Pipe couplings are highly demanded in the pipe fitting market. Pipe couplings are fittings that help to extend or terminate pipe runs. These fittings are also used to change pipe size. Couplings extend a run by joining two lengths of pipe. They are known as reduced coupling if they are used to connect pipes of different sizes. Couplings are also known as repair couplings. These couplings are without stops or ridges and they can be fixed anywhere along the pipe length for preventing leak of any kind.  Material:  ASTM A105, F304, F316, F304L, F316L, A182, F11, F22, and F91  Pressure:  2000LBS, 3000LBS, 6000LBS, 9000LBS  Size:  from 1/4 to 4 inches  Standard:  ANSI B16.9/B16.28 and MSS SP-43/SP-75  Connection ends:  butt welded, threaded  Thread types:  NU, EU, STC, LTC and BTC Surface treatment: Shot blasted, rust-proof black oil Packing:  Plywood Case/ Pallet/ other

Threaded Flanges are confined to special applications. Their chief merit lies in the fact that they can be assembled without welding this explains their use in extremely high pressure services, particularly at or near atmospheric temperature, when alloy steel is essential for strength and where the necessary post weld heat treatment is impractical. Threaded Flanges are unsuited for conditions involving temperature or bending stresses of any magnitude, particularly under cyclic conditions, where leakage through the threads may occur in relatively few cycles of heating or stress; sea welding is sometimes employed to overcome this, but cannot be considered as entirely satisfaction. Key Features:   Can be attached to the pipe without welding (sometimes an additional seal weld is used as well) Ideal for higher pressure and temperature applications for small pipe sizes Not recommended for larger loads, especially when subjected to higher torque  Uses of threaded flanges: Threaded flanges can be fitted to pipes of various sizes without welding and this is one chief benefit for which these flanges are highly demanded. They can be used in extremely high pressure applications, particularly at or near atmospheric temperature, where the necessary post weld heat treatment is not possible. They are ideal for small diameter piping applications. They are economical and time saving devices. These threaded flanges are normally designed for non-cyclic applications. The flanges are suitable to be used in applications where welding is hazardous. They can be used in highly explosive areas.

Weld Neck Flanges are drilled(machined) with the wall thickness of the flange having the same dimensions of the matching pipe, the lighter the pipe is, the larger the bore, conversely, the heavier the pipe, the small the bore, they are normally used for highpressure, cold or hot temperature Notes : Flange dimensions to ANSI B16.5.  Dimensions "B" & "D" includes raised face thickness. Bore (SCH) "C" purchasess to Specity. Larger outlet sizes are avilable on applications. ANSI 150# / 300# 2mm Raised Face.  ANSI 600# / 2500# 7mm Raised Face.   Key Features: This is the most common type of high pressure pipe flange. They are distinguished from other types of pipe flanges by their long tapered hub and gentle transition of thickness in the region of the butt weld joining them to the pipe. The long tapered hub provides an important reinforcement of the weld neck flange proper in terms of strength and resistance to dishing. Uses of weld neck flanges: The weld neck flange is very resistant to dishing and has a very sturdy connection because it has the pipe along with the tapered hub. The flanges are ideal for extreme fluctuations of temperature. They are ideal in environments where there may be a lot of bending and handling of the flanges. Preferred in an environment with extreme temperature conditions. This type of flange is preferred for every severe service condition—resulting from high pressure or from sub-zero or elevated temperature. They are used in situations where loading conditions are substantially constant or fluctuate between wide limits. This is probably the best welding flange available because of its high, heavy neck. Highly recommended wherever a sound welded joint connection is needed.

Pipe Tee is a type of pipe fitting which is T-shaped having two outlets, at 90 o to the connection to the main line. Pipe Tee is a short piece of pipe with a lateral outlet. Pipe Tee is used to connect pipelines with a pipe at a right angle with the line. Pipe Tees are widely used as pipe fittings. These are made of various materials and available in various sizes and finishes. Pipe Tee is extensively used in pipeline networks to transport two-phase fluid mixtures.    Specifications Material : Stainless Steel: Astm A403 Wp 304 / 304l / 316 / 316l / 317 / 317l / 321 / 309 / 310 / 904l, Etc. & also in Cs, as As per Standard. Size : 1/2" to 24" Pressure : Sch 5s to Sch Xxs. Industrial Applications Include : Chemical processing Petroleum Pulp paper Refining Textile Waste treatment Marine Utilities power generation Industrial equipment Automotive Gas compression and distribution industries Pipe tees are also recommended for industrial plant fluid power systems.   Features of Pipe Tees : Pipe tees are widely used in various commercial and industrial applications. There are three female openings in a t shaped pipe tee. There are straight pipe tees which have the same size openings. Reducing pipe tees have one opening of different size and two openings of the same size. There are sanitary pipe tees which are used in waste lines. These kind of pipe tees have a curved branch which is designed for a clean out plug. They are used to prevent obstruction of waste. A cross pipe tee has four equal sized female openings. A wing pipe tee has lugs to fasten the fitting to a wall or stud. A compression pipe tee uses compression fittings on two or more ends. A test pipe tee has a threaded opening. This opening is used in conjunction with a threaded plug for a clean-out opening on a drain pipe

Weld Neck Flanges are fittings used in place of welded flanges where rotating back up flanges are desired. They are also called lap joints and vanstone flared laps. A rotating back up flange seats itself against the back surface of the stub end. When bolts are added, the clamping action of the bolts presses the rotating back up flange against the back of the stub end. The gasket surface of the stub end then presses against a gasket and another gasket surface providing joints like standard flange joints. The seal is made by the gasket surface of the stub end alone, the flange only provides the clamping pressure on the joint. Our high quality Weld Neck Flanges (butt weld fittings) are tested and verified for durability, accuracy and precision. The Weld Neck Flanges are manufactured in all standard dimensions. The Weld Neck Flanges are provided with a standard weld bevel and can be available in squared,  flanged,  Victaulic and threaded ends. We offer Weld Neck Flanges at highly competitive prices.   Specifications Material : ASTM A182 F 304 / 304L / 316 / 316L / 317 / 317L / 321 / 309 / 310 / 904 / F1 / F5 / F9 / F11 / F22 ETC. & ALSO IN CS Size : 1/2" TO 24" Pressure : Sch 5s to Sch Xxs. Class : 150#, 300#, 600#, 900#, 1500#, 2500#

Lap Joint flanges are used on piping fitted with with lapped pipe or with lap joint stub ends. The lap joint flange with the stub end assembly are normally used in systems requiring frequent dismantling for inspection and cleaning and where the ability to swivel flanges and to align bolt holes materially eases the erection of large diameter or unusually stiff piping. These flanges are also used in applications where there is a need to facilitate bolt alignment. These type of flanges are similar to slip-on flanges. The only difference is that it has a curved radius at the bore and face to accommodate a lap joint stub end. They may be used at all pressures and are available in a full size range. These lap joint flanges slip over the pipe, and are not welded. They are otherwise fastened to it. Here the bolting pressure is transferred to the gasket by the pressure of the flange against the back of the pipe lap. Material: Nickel Alloys :  Monel 400 & 500, Inconel 600 & 625, Incolloy 800, 825, Hastelloy C22, C276   Size :  1/8" NB TO 48"NB. Class :  150#, 300#, 400 #, 600#, 900#, 1500# & 2500 #. Standard : ANSI :  ANSI B16.5, ANSI B16.47, MSS SP44, ANSI B16.36, ANSI B16.48 DIN : DIN2527, DIN2566, DIN2573, DIN2576, DIN2641, DIN2642, DIN2655, DIN2656, DIN2627, DIN2628, DIN2629, DIN 2631, DIN2632, DIN2633, DIN2634, DIN2635, DIN2636, DIN2637, DIN2638, DIN2673 B.S :  BS4504 , BS4504, BS1560, BS10 Advantages of Lap Joint Flanges: Lap Joint flanges have certain special advantages over other flanges. These are as follows: Lap Joint flanges have the freedom to swivel around the pipe. This facilitates the lining up of opposing flange bolt holes. Lack of contact with the fluid inside the pipe leads to the greater durability of these flanges. In piping systems which corrode or erode quickly, the lap joint flanges may be salvaged for re-use. The pressure-holding capacity of lap joint flanges is little. But it is better than that of slip-on flanges. The Lap Joint works as a backing ring on the stub. The main advantage of lap joint flange is that the bolt holes can be aligned with the matching flange after the welds have been completed. They allow rotational alignment capability.

A pipe bending machine is vital component for any pipe bending project, particularly those of a large scale. A pipe bending machine makes the job easier and is capable of completing multiple jobs in less time than when working by hand. A pipe bending machine can be either handheld or floor mounted. In either case, the pipe bending machine allows the user to hold the pipe at one end of the channel while the shape roller forces the pipe through and carries it around in a curve. A pipe bending machine can be purchased with a variety of pipe bending capabilities.  Material:  A234-WPB A234-WP12 A234-WP11 A234-WP5 A403-WP304 A403-WP304L A403-WP316. A403-WP316L A420-WPL6, Ceramic Lined  Special alloys:  cooper nickel,  Ni-based,  Cu-based,  Co-based,  Fe-based Size:  Outer Diameter (D): D

Coupling fittings are used for fluid conduits in which each end portion of two tubes to be connected is provided with a swaged-on adapter carrying the necessary means to connect or disconnect the tubes without disturbing the swaged-on adapter. Our range of coupling fittings are available in aluminium, steel and bronze. Pipe couplings are highly demanded in the pipe fitting market. Pipe couplings are fittings that help to extend or terminate pipe runs. These fittings are also used to change pipe size. Couplings extend a run by joining two lengths of pipe. They are known as reduced coupling if they are used to connect pipes of different sizes. Couplings are also known as repair couplings. These couplings are without stops or ridges and they can be fixed anywhere along the pipe length for preventing leak of any kind.  Material:  ASTM A105, F304, F316, F304L, F316L, A182, F11, F22, and F91  Pressure:  2000LBS, 3000LBS, 6000LBS, 9000LBS  Size:  from 1/4 to 4 inches  Standard:  ANSI B16.9/B16.28 and MSS SP-43/SP-75  Connection ends:  butt welded, threaded  Thread types:  NU, EU, STC, LTC and BTC Surface treatment: Shot blasted, rust-proof black oil Packing:  Plywood Case/ Pallet/ other

Pipe Elbows are fitting accessories which are widely used in various industrial sectors for pipe fitting. A Pipe Elbow is frequently used in pressurized applications and is available in various shapes and sizes for use in different applications. The Pipe Elbow, we offer, is manufactured by using high-grade materials that offer it qualitative attributes like high strength, corrosion resistance, durability, etc. Specifications Material : Stainless Steel: Astm A403 Wp 304 / 304l / 316 / 316l / 317 / 317l / 321 / 309 / 310 / 904l, Etc. & also in Cs, as As per Standard. Size : 1/2" to 24" Pressure : Sch 5s to Sch Xxs.

Pipe reducer are tube fittings that are widely used in a number of industries in order to providing greatest connection flexibility in connecting fractional tubes in various installations. Pipe reducer is a kind of pipe fitting that joins two pipes of different diameter. The pipe reducers are available in a range of materials depending on the end use of the products and these fittings are manufactured in inch and metric size.  Pipe reducers are special type of tube fittings that are commonly used in the demanding environments of chemical and power plants. They provide a highly reliable, sturdy and tight integral line system and these type of pipe fittings remain unaffected by shock, vibration or thermal distortion. These pipe fittings are very easy to install and they resist leakage due to thermal or pressure cycling. These reducers are sometimes chrome or nickel coated to prevent corrosion and increase the life of the product. An  Eccentric reducer , also called a  Bell reducer , has two female (inside) threads of different sizes with centers so designed that when they are joined, the two pieces of pipe are not in line with each other, but they can be installed so as to provide optimum drainage of the line. 

The Full Coupling fittings are used for fluid conduits in which each end portion of two tubes to be connected is provided with a swaged-on adapter carrying the necessary means to connect or disconnect the tubes without disturbing the swaged-on adapter. Our range of coupling fittings is available in aluminum, steel and bronze. Full Coupling is highly demanded in the pipe fitting market. Full Coupling pipe fittings are such fittings that help to extend or terminate pipe runs. Full Coupling is also used to change pipe size. Couplings extend a run by joining two lengths of pipe. They are known as reduced coupling if they are used to connect pipes of different sizes. These couplings are also known as repair couplings. These couplings are without stops or ridges and they can be fixed anywhere along the pipe length for preventing leakage of any kind.     Specifications Material : Stainless Steel: Astm A403 Wp 304 / 304l / 316 / 316l / 317 / 317l / 321 / 309 / 310 / 904l, Etc. & also in Cs, as As per Standard. Size : 1/2" to 24" Pressure : Sch 5s to Sch Xxs.

Pipe Tee is a type of pipe fitting which is T-shaped having two outlets, at 90 o to the connection to the main line. Pipe Tee is a short piece of pipe with a lateral outlet. Pipe Tee is used to connect pipelines with a pipe at a right angle with the line. Pipe Tees are widely used as pipe fittings. These are made of various materials and available in various sizes and finishes. Pipe Tee is extensively used in pipeline networks to transport two-phase fluid mixtures.    Specifications Material : Stainless Steel: Astm A403 Wp 304 / 304l / 316 / 316l / 317 / 317l / 321 / 309 / 310 / 904l, Etc. & also in Cs, as As per Standard. Size : 1/2" to 24" Pressure : Sch 5s to Sch Xxs. Industrial Applications Include : Chemical processing Petroleum Pulp paper Refining Textile Waste treatment Marine Utilities power generation Industrial equipment Automotive Gas compression and distribution industries Pipe tees are also recommended for industrial plant fluid power systems.   Features of Pipe Tees : Pipe tees are widely used in various commercial and industrial applications. There are three female openings in a t shaped pipe tee. There are straight pipe tees which have the same size openings. Reducing pipe tees have one opening of different size and two openings of the same size. There are sanitary pipe tees which are used in waste lines. These kind of pipe tees have a curved branch which is designed for a clean out plug. They are used to prevent obstruction of waste. A cross pipe tee has four equal sized female openings. A wing pipe tee has lugs to fasten the fitting to a wall or stud. A compression pipe tee uses compression fittings on two or more ends. A test pipe tee has a threaded opening. This opening is used in conjunction with a threaded plug for a clean-out opening on a drain pipe