Overload protector is really very useful against the protection of elevator controlling machines and inverter. It is really very useful as it deals with the capability of the elevators as per the requirement hence it enhances the life time of the lift which is currently under the use. Capable of measuring up to 5 tons of weight (Cabin weight + structure + payload). Two relay outputs available, one for full load and other for over load. Easily operates on 230 volt AC supply Simple Programming mode for weight setting is available. Seven segment display is available for weight readings. Several LED indicators are available to highlight certain event indications. Lift load detection through measurement of stress of traction ropes. Low weight and compact in size. Easily installable on the cabin.

Unit has Compact Door Drive with PMDC Motor for Auto Door Lift. Unit works with any kind of doors. It senses the opening span automatically at the time of setup / installation. Manual Tuning doesn't required, Self-Learning is automatically executed during set-up. User can set Function Parameters by using Keys and Segment. Information Manual carries information about the Function Parameters. The Connection Diagram mentioned on Drive itself. Door Motor 24V PMDC Motor (Variants: 60W, 100W, Power Capacity depends on the size of the doors). Planetary Geared & Worm Geared Variants are available. Motor equipped with high resolution Encoder. Door Motor Auto-Learning for the span of the door travel distance. Curved Profile for the operation of door opening & door closing, doesn't require to set any other extra parameters, like; Fast Speed, Slow Speed, Slow Located Distance etc. Use motor equipped encoder, so smooth start & stop function without extra limit proxy switches. Door Opened & Door Closed acknowledgement signals through Relay output.

The elevator integrated drive and controller is designed with closed loop vector controller for higher performance. Zero-speed torque compensation system without load weighing device helps save cost. Dynamic PWM carrier modulation technology ensures reduced motor noise. The elevator integrated drive and controller is suitable for both synchronous and asynchronous motor. Dual 32-bit embedded microprocessor. All Type of encoder is supported. This product is applicable for residential lift, goods lift, car lift, ramp elevator, Home Lift, Hospital Lift. This product Parallel and Serial communication both option available. Redundancy control through Multi-CPUs. equipped with CAN Bus, Mod Bus and GSM Communication Technology. Based on displacement calculation methods derive N velocity profile to achieve optimum direct-to-floor distance control. Simple 4 wire serial communications to commission duplex group control Group control with less than 8 elevators is based on fuzzy logic control theory in-built real-time clock to facilitate time-sharing control and elevator management. Flexible emergency backup power; 220Vac UPS power input makes emergency evacuation easy. Automatic identification operation between short-floors. Handheld Operation Tools: Mini Keypad, PDA, PC to facilitate easy commissioning. 60 fault codes to facilitate easy diagnostics. Power on reset run to groupand floor is not required. Shaft position learning is standard. Direct-to-floor landing. Smooth ride comfort, optimal travel mean time. Power on reset run is not needed. Practical reliable power Failure auto rescue emergency operation using 220V. 1ph UPS/ARD. Automatic identification operation between short-floors with different floor heights. Advance door opening and re Leveling using option card. 7 segment LED display for floor position indicator. Wide variety of door function control lo meet different needs in freight lift doors requirement. Parallel wiring control for all digital input and output. Optimum Exclusive function, quick easy start-up periods. Pre-factory default parameters setting facilitate zero parameter setting at site. All inputs and outputs are user programmable. Suitable for auto door as well as manual door. Power Rating 2.2 kW to 45 kW, 3 Phase 380/400/415V 2.2 kW to 30 kW. 3 Phase 220V 2.2 kW to 3.7 kW. 1 Phase 220V

AD200 Series High Performance Open Loop Vector Control inverter. Applying the most advanced sensorless vector control which keeps pace with the leading international level and 32-bit DSP system. The product enhances its reliability to meet the requirements of environment adaptability, customized and industrialized design withmore optimized functions, more flexible applications and more stable performance. Modular design of Fans and Capacitor for easy replacement and maintenance. External LED keypad to copy parameters; Optional LCD keypad provided. Emergency Power Supply (EPS) Function with Just a 220VAC Single Phase UPS. Double Safety protection examine, output phase loss at all time and check torque output before releasing the mechanical brake. Auto tune motor parameter without load disconnection. 4 KW, 5.5KW and 7.5KW Power Rating. 440VAC Three Phase Power Supply. 220VAC Single Phase for Emergency Power Supply. Open loop vector inverters for controlling asynchronous AC induction motors and permanent magnet synchronous motors. Up to 0.25Hz/150% starting torque(Asynchronous motor); 2.5Hz/150% starting torque (Synchronous motor)

• Relay output1A, 230VAC/2A, 30VDC
• Sensor32 Pairs
• Size154x50x31 mm

In case of a main power supply failure, the lift stopped between two floors is moved to floor level, the automatic door is opened and passengers are out safely, For lifts with automatic door, in case of a main power supply failure at floor level, the door is remain opened. Input Voltage: Three Phase 440VAC, 50Hz Pure Sine Wave Main Line Voltage Output Voltage: Two Phase 440VAC, 50Hz Modified Square wave with power Booster Logic. Battery Voltage: 72V (6 Battery of 12V) and Amp depend upon the Motor Rating

In case of a main power supply failure, the lift stopped between two floors is moved to floor level, the automatic door is opened and passengers are out safely, For lifts with automatic door, in case of a main power supply failure at floor level, the door is remain opened. Input Voltage: Three Phase 440VAC, 50Hz Pure Sine Wave Main Line Voltage Output Voltage: Two Phase 440VAC, 50Hz Modified Square wave with power Booster Logic. Battery Voltage: 72V (6 Battery of 12V) and Amp depend upon the Motor Rating

AD200 Series High Performance Open Loop Vector Control inverter. Applying the most advanced sensorless vector control which keeps pace with the leading international level and 32-bit DSP system. The product enhances its reliability to meet the requirements of environment adaptability, customized and industrialized design withmore optimized functions, more flexible applications and more stable performance. Modular design of Fans and Capacitor for easy replacement and maintenance. External LED keypad to copy parameters; Optional LCD keypad provided. Emergency Power Supply (EPS) Function with Just a 220VAC Single Phase UPS. Double Safety protection examine, output phase loss at all time and check torque output before releasing the mechanical brake. Auto tune motor parameter without load disconnection. 4 KW, 5.5KW and 7.5KW Power Rating. 440VAC Three Phase Power Supply. 220VAC Single Phase for Emergency Power Supply. Open loop vector inverters for controlling asynchronous AC induction motors and permanent magnet synchronous motors. Up to 0.25Hz/150% starting torque(Asynchronous motor); 2.5Hz/150% starting torque (Synchronous motor)

Unit has Compact Door Drive with PMDC Motor for Auto Door Lift. Unit works with any kind of doors. It senses the opening span automatically at the time of setup / installation. Manual Tuning doesn't required, Self-Learning is automatically executed during set-up. User can set Function Parameters by using Keys and Segment. Information Manual carries information about the Function Parameters. The Connection Diagram mentioned on Drive itself. Door Motor 24V PMDC Motor (Variants: 60W, 100W, Power Capacity depends on the size of the doors). Planetary Geared & Worm Geared Variants are available. Motor equipped with high resolution Encoder. Door Motor Auto-Learning for the span of the door travel distance. Curved Profile for the operation of door opening & door closing, doesn't require to set any other extra parameters, like; Fast Speed, Slow Speed, Slow Located Distance etc. Use motor equipped encoder, so smooth start & stop function without extra limit proxy switches. Door Opened & Door Closed acknowledgement signals through Relay output.

• Input VoltageThree Phase 440VAC, 50Hz Pure Sine Wave Main Line Voltage.
• Output VoltageTwo Phase 440VAC, 50Hz Modified Square wave with power Booster Logic.

• Wide input voltage range12V - 35V DC

General purpose display panel for Landing and COP.320x240 pixel color TFT LCD panel.Wide input voltage range 12V - 35V DC.Can be mounted in horizontal in COP as well as landing.Advertisement function increases the added value of displays, and express users' uniqueness and diverseness.Users can change massages by themselves, such as background pictures, arrow, floor, time and date.High definition makes the images more active and lively.

Overload protector is really very useful against the protection of elevator controlling machines and inverter. It is really very useful as it deals with the capability of the elevators as per the requirement hence it enhances the life time of the lift which is currently under the use. Capable of measuring up to 5 tons of weight (Cabin weight + structure + payload). Two relay outputs available, one for full load and other for over load. Easily operates on 230 volt AC supply Simple Programming mode for weight setting is available. Seven segment display is available for weight readings. Several LED indicators are available to highlight certain event indications. Lift load detection through measurement of stress of traction ropes. Low weight and compact in size. Easily installable on the cabin.