Saharanpur, Uttar Pradesh, India
Our Products
The Wet Washing System is intended to wash raw material like wheat/rice straw that are high in silica and chlorides. The procedure recuperates the water utilized as a part of the washing process and render fiber with the right consistency into the pulping framework.
Equipments
Advantages
Application
D Pulper design to reduce the dwelling time and increases the strength of the pulp. It is used to process fibrous materials (such as recycled paper) into usable slurry for manufacturing processes. They are used primarily in the pulp and paper manufacturing industry. Suitable for furnish of Virgin Pulp, Mix Waste, Broke, Box Board Cutting, Kraft Cutting Etc.
Features
The Hi-con. Pulper designed for slushing the contaminated, unsorted or sorted waste paper such as note books NCC, SACK KRAFT, OCC, NDLKC, INDIAN CUTTING etc. the pulperoperates a special rotor, the rotor made out from Cast steel (SS316, 304 grade)with coated edge. Its operates from 14 to 15 % consistency
Features
pulp cleaners for the pulp and paper industry to remove dense contaminants from paper pulp. These units fall into two basic categories: continuous rejects cleaners that are usually installed in multiple stages to remove fine sand from paper pulp and intermittent rejects cleaners that are designed to collect larger reject material and to discharge it intermittently to minimize fibre loss.
Features
The Trommel is a drum washer designed to further separate the remaining fibers from the discharged contaminants from the de-trasher in the Pulper. The Trommel is a horizontal drum washer specially designed to overcome the, problems inherent with other designs, like mechanical problems on drive, noisy operation. Cost of maintenance and difficult installation.
Benefits
The unique design for lye mixture help to proper mixing of the material (water, chemical & lye) and dump in the digester system then the Packer also help to pack the maximum material in the digester system. The design of lye mixer and its track is vary according to suitability of space and the requirement of the customer.
A need for good quality waste papers has become increasingly important for the pulp and paper industry. Under such circumstances. We have concentrated all sorts of efforts to develop? waste paper treating machineries to meet contemporary needs. We found the kneading applied to the stock while processing produces a good result in terms of de-inking, and that the dewatering prior to kneading is an important point for de-inking, Machine developed for this purpose is applicable to any type of waste paper stock as well as a virgin pulp. We are, with an original state of the technology and know how as well as practical experiences in the pulp and paper stock preparation machineries, always at your disposal for the request to improve your stock preparation system.
Features
The Turbo Separator uses centrifugal forces to stratify the stock into three regions, heavy rejects, light rejects and acceptable materials (accepts/fibres). Heavy rejects are forced against the outside wall, light rejects remain in the centre, and acceptable materials (accepts/fibres) migrate to the region in between. Heavy rejects exit the Turbo Separator via a tangential pipe at the top of the machine. This enables them to exit at high pressure. No pump is needed to move them to the High/medium/low Density Cleaner (Secondary fibre recovery device). Light rejects exit.
Features
Centri cleaners is designed and manufactured from high quality SS 304 & 316 sheets for highly efficient removal of light particles such as sand, bark, dirt, specks and shives, The design and finishing has proved a high cleaning efficiency. The Centricleaner is also polished from inside for high cleaning efficiency and outside for better finish and good look, The quality and workmanship pays off in unbeatable long term performance and life. The Centricleaner is provided in different capacities as per the choice and need of the users. The normal capacity available is from 400 LPM to 1500 LPM.
Features
B
The heater mixer help to shredded stock heated to 90 -110o C, in heater mixer maintain the temperature control through the control panel
The dilution Pulperinstall with the Hi con Pulper(accept line of the high consistency pulper)
The dilution Pulper is designed and constructed to ensure the efficient separation of fibers from the contaminants
Its operates from 4 % consistency
The washing drums helps to washing the pulp and wash the impurities of the pulp such as inks, blackish patches etc.
Features
After passing the paper from whole Press Section, Paper remains still wet hence it requires to eliminate remaining water which can only be completed through the application of heat. This is carried out by Paper Machine Drying section consist of a series of steam heated cylinders varying in diameter. These Dryers they fabricate from Mild Steel which has top quality and high efficiency with hydrolic testing.
