Write a Review
Our Products
We are leaders in the market for providing best range of PROPELLER CW, FEMALE JACK DC SOCKET, LED DISPLAY COMMON ANODE, Oled Display and Sensor Module
A set of 2 x 1045 Propellers. The set includes one clockwise rotating and one counter-clockwise rotating propeller with 2 x propeller shaft adapters. The adapters allow the propeller to be used with motors of different shaft diameters.
This 1045 propeller can be used with brushless motors with a 800-1800 kV rating. With a low kV motor(800 1400 kV), this propeller offers smooth flights with longer flight times perfect for FPV and aerial photography. With a high kV motor (more than 1200 kV) this propeller offers fast flights perfect for acrobatic flights.
Note: Buy additional propellers than required on your multirotor as propellers are regularly broken during flight crashes
The DC Gear motor offers custom engineering solutions based on a wide range of low voltage DC and high voltage DC motor platforms. The low voltage DC platform provides power density and compact packaging options.
Features of 200 RPM Gear DC Motor at 12V:
Application of DC Motor 12V:
This is a graphical LCD 12864 pixel with White LED backlight .It can display not just alphanumeric characters but also simple graphics. Can handle 128*64 pixels.
This is a framed graphical LCD 64128 with LED backlight.
This unit is a very clear STN type LCD with a simple command interface. T
his new module includes the negative voltage circuitry on board!
Utilizes the extremely common KS0108B parallel interface chipset (datasheet). I
nterface code is freely available. Includes LED Backlight.
2 Pin PCB Mount Terminal Block 5.08mm/0.2 Pitch Wire to Board Connector 10A
Introduction:
This 2 Pin Wire to Board connector are used widely for connecting Wires to Boards, it can be for Power Supply or connecting any other peripheral like Motor to the Board. The distance between two mounting pins is in multiple of standard 2.54 mm so that this connector can be mounted easily on general purpose PCBs. This connector can be used safely for current of up to 10 A.
This module can take an input voltage of between 5 and 32V DC and converts it to an output voltage between 5 and 35V DC.
You may use this module to generate high voltage upto 32V from small battery packs other power sources.
Features
Test Results
Vin * Iin * Efficiency = Vout * Iout
Vin: Input Voltage
Iin: Input current
Vout: Output Voltage
Iout: Output current
Technical Parameters:
7 Segment Led Display Common Anode for Arduino/Raspberry-Pi/Robotics
Aseven-segment display(SSD), orseven-segment indicator, is a form of electronicdisplay devicefor displayingdecimal numeralsthat is an alternative to the more complexdot matrixdisplays.
Seven-segment displays are widely used indigital clocks, electronic meters, and other electronic devices for displaying numerical information.
The seven elements of the display can be lit in different combinations to represent thenumerals. In a simple LED package, typically all of thecathodes(negative terminals) or all of theanodes(positive terminals) of the segment LEDs are connected and brought out to a common pin; this is referred to as a common cathode or common anode device. Hence a 7 segments plus decimal point package will only require nine pins (though commercial products typically contain more pins, and/or spaces where pins would go, in order to match standardICsockets. Integrated displays also exist, with single or multiple digits. Hexadecimaldigits can be displayed on seven-segment displays. A particular combination of uppercase and lowercase letters are used for AF. In addition, seven segment displays can be used to show various other letters of theLatin, CyrillicandGreek alphabetsincludingpunctuation. Multiple-digit LED displays as used in pocket calculators and similar devices usedmultiplexed displaysto reduce the number of I/O pins required to control the display. For example, all the anodes of the A segments of each digit position would be connected together and to adriver circuitpin, while the cathodes of all segments for each digit would be connected. To operate any particular segment of any digit, the controlling integrated circuit would turn on the cathode driver for the selected digit, and the anode drivers for the desired segments; then after a short blanking interval the next digit would be selected and new segments lit, in a sequential fashion. In this manner an eight digit display with seven segments and a decimal point would require only 8 cathode drivers and 8 anode drivers, instead of sixty-four drivers and IC pins.
This module is a 0.96 inch blue OLED display module. The display module can be interfaced with any microcontroller using SPI/IIC protocols. It is having a resolution of 12864. OLED is a self light-emitting technology composed of a thin, multi-layered organic film placed between an anode and cathode. In contrast to LCD technology, OLED does not require a backlight. OLED possesses high application potential for virtually all types of displays and is regarded as the ultimate technology for the next generation of flat-panel displays.
OLEDsbasic structure consists of organic materials positioned between the cathode and the anode, which is composed of electric conductive transparent Indium Tin Oxide. The organic materials compose a multi-layered thin film, which includes the Hole Transporting Layer, Emission Layer and the Electron Transporting Layer. By applying the appropriate electric voltage, holes and electrons are injected into the EML from the anode and the cathode, respectively.
This module integratesDHT11sensor and other required components on a small PCB. The DHT11 sensor includes a resistive-type humidity measurement component, an NTC temperature measurement component and a high-performance 8-bit microcontroller inside, and provides calibrated digital signal output.
It has high reliability and excellent long-term stability, thanks to the exclusive digital signal acquisition technique and temperature & humidity sensing technology.
This is a multipurpose PCB or we can say that Vero board or zero size PCB is a copper clad laminated board used in various electronic fields for circuit designing and testing.
FEATURES OF MULTI PURPOSE PCB BOARD(12CMX18CM):
B.M. EMBEDDED SOLUTIONS (B.M. EMBEDDED SOLUTIONS)
UG-1, Vishwa Sadan Building, District Center, Janak Puri, Janakpuri, Delhi - 110058
Share us via
