Nagpur, Maharashtra, India GST : 27AAACB5340H1ZY Verified Supplier
Our Product / Services
Leading Manufacturer, Supplier & Retailer of Lint Cleaner, Centrifugal Lint Cleaner and Linter Cleaner.
Features & Benefits : Removes seeds coats, leafy matter after ginning. Improves lint grade & appearance. Reduces trash content & other contamination. Eliminates micro-dust effectively. Precise design preserves fiber properties. Removes short fiber clusters from ginned lint. Better quality lint yields higher returns. Easy to maintain; Low maintenance cost. Available in different models with different feeding systems for specific requirements. Can be incorporated in pneumatic conveying system for online cleaning. Considerable saving in labour cost.
|Model I||Model II||Model III|
|No. of cleaning cylinders||Six||Three||Four|
|Width||1200/1500/ 1800 mm||1200/1500/ 1800 mm||1200/1500/ 1800 mm|
|Cleaning Capacity (Lint)||1200/1500/2000 Kg/Hour||1200/1500/2000 Kg/Hour||1200/1500/2000 Kg/Hour|
|Connected total power||7 HP||7 HP||7 HP|
The Centrifugal Lint Cleaner is a flow-through (air-jet type) lint cleaner. Ginned lint is conveyed by air into the cleaner through a constricting duct at a relatively high velocity. Air and cotton moving through the inlet duct make an abrupt change in direction as they pass across an adjustable mote opening. The heavier trash is ejected through the operating by inertial forces while lint is carried through the cleaner by the airstream. The amount of trash removed is controlled by the size of the adjustable mote opening. This opening can be adjusted during operation by a handwheel on the exterior of the machine. An external graduated scale having numbers 0 through 10 provides an adjustment reference point. Ejection of trash can be observed through a window on each end or through the door on the front. In the event of a tag forming in the constricting duct, a lever is provided on top of the cleaner to quickly move the mote opening to the full open position.
Working principle of Linter Cleaner Linter is discharged from a cyclone to the top chamber of the LC-410D Linter Cleaner. This chamber consists of two x 3 Meter' long, 500 MM diameter cylindrical beaters operating side by side in 550MM dia. Half round screen sections. Linter enters at one end of one beater, is conveyed to the opposite end and transferred to the opposite beater section. From this point, the Linter is once again conveyed over the screen section for the length the top section. Cleaned Linter discharged from the top section is pneumatically conveyed to the bale press. Any Linter, which passes through the perforated screen of the top section, along with trash, is discharged into the first of the two pepper sections. These sections are clothed with fine wire mesh for the removal of the very fine hull particles (hull pepper) generated in the saw delinting process. Linter then passes to the reclaim section for final cleaning.The reclaimed Linter is then discharged and may be conveyed to a motes beater or recycled to the Linter cleaner. In addition to the 6 Meters of hull pepper removal screens the, LC410D also incorporates Automatic Screen Cleaning which blows down the entire length of both hull pepper sections with high-pressure air. Manual blow-down and unnecessary shutdown are eliminated. This also provides for consistent length of effective cleaning throughout the daily operations. This blow down system is PLC controlled and can be programmed for both duration & frequency of the air blasts. Salient features of our Dryer Lint Cleaner Maximum cellulose yieldCapacity – 15 TPD Linter28% greater cleaning surface area for first-pass cleaning than othersAdditional cleaning where needed most; three times the effective pepper section cleaning than the closest competitorReclaim section designed to accommodate any additional shale removal which may be required.Automatic screen cleaning; programmable to specific requirements
|2 x 500 MM Beaters||3 PH , 1000 RPM|
|Pepper section and reclaim section rolls||3 HP, 1000 RPM|