Our Product / Services
Manual Return Bolt Tensioner
Tool Ref Load Cell |
Bolt Diameter | Tool Load | Hydraulic Area | Aprox. Weight | ||||||
---|---|---|---|---|---|---|---|---|---|---|
Imp. | Kit No. | Metric | Kit No. | Ton Short | KN | (in2) | (mm2) | (lbs) | (kg) | |
MTRAS010001 (MRT1) | 1” 1 1/8” |
MRTAS0010002 MRTAS0010003 |
M24 M27 |
MRTAS010004 MRTAS010005 |
31.5 | 280 | 2.89 | 1867 | 6.6 | 3.0 |
MTRAS020001 (MRT 2) | 1” 1 1/8" 1 1/4” 1 3/8" |
MRTAS0020002 MRTAS020003 MRTAS020004 MRTAS020005 |
M24 |
MRTAS020006 MRTAS020007 MRTAS020008 MRTAS020009 MRTAS020010 |
506.0 | 450 | 4.65 | 3001 | 9.9 | 4.5 |
MTRAS030001 (MRT 3) | 1-1/4” 1-3/8” 1-1/2” 1-5/8” |
MRTAS030002 MRTAS030003 MRTAS030004 MRTAS030005 |
M33 M36 M39 M42 |
MRTAS030006 MRTAS030007 MRTAS030008 MRTAS030009 |
75.0 | 660 | 6.82 | 4401 | 12.98 | 5.9 |
MTRAS040001 (MRT 4) | 1-1/2” 1-5/8” 1-3/4” 1-7/8” 2" |
MRTAS040003 MRTAS040004 MRTAS040005 MRTAS040006 MRTAS040007 |
M39 M42 M45 M48 |
MRTAS040008 MRTAS040009 MRTAS040010 MRTAS040011 |
112.0 | 1000 | 10.34 | 6668 | 18.70 | 8.5 |
MTRAS050001 (MRT 5) | 2” 2-1/4” 2-1/2” 2-3/4” |
MRTAS050003 MRTAS050004 MRTAS050005 MRTAS050006 |
M52 M56 M60 M64 M68 M70 |
MRTAS050007 MRTAS050008 MRTAS050009 MRTAS050010 MRTAS050011 MRTAS050012 |
168.0 | 1500 | 15.50 | 10003 | 30.80 | 14.0 |
MTRAS060001 (MRT6) | 2-3/4” 3” 3-1/4” 3-1/2” |
MRTAS060003 MRTAS060004 MRTAS060005 MRTAS060006 |
M72 M76 M80 M85 M90 |
MRTAS060007 MRTAS060008 MRTAS060009 MRTAS060010 MRTAS060011 |
281.0 | 2500 | 25.84 | 16671 | 50.60 | 23.0 |
The Spring Return design dramatically increases productivity and safety on the job site when compared to older technology manual return tensioners.
Order a load cell and an adaptor kit to make a complete tensioner.
Each are sold separately.
Tool Ref Load Cell |
Stud Diameter | Tool Load | Hydraulic Area | Approx. Weight |
||||||
---|---|---|---|---|---|---|---|---|---|---|
Imperial |
Adapter Kit Order No. |
Metric |
Adapter Kit Order No. |
Lbs (tonf) |
KN |
(in2) |
(mm2) |
|||
(lbs.) |
(kg.) |
|||||||||
SRT 0 SRTAS000001 |
3/4" 7/8" |
SRTAS000002 SRTAS000004 |
M20 M22 |
SRTAS000006 SRTAS000008 |
35494 (16.1) |
160 | 1.65 | 1067 | 3.1 | 1.4 |
SRT 1 SRTAS010001 |
1" 1-1/8" |
SRTAS010003 SRTAS010005 |
M24 M27 |
SRTAS010007 SRTAS010009 |
61949 (28.1) |
280 | 2.89 | 1867 | 6.0 | 2.7 |
SRT 2 SRTAS020001 |
1" 1-1/8" 1-1/4" 1-3/8" |
SRTAS020003 SRTAS020005 SRTAS020007 SRTAS020009 |
M24 M27 M30 M33 M36 |
SRTAS020011 |
99648 (45.2) |
450 | 4.65 | 3001 | 9.0 | 4.1 |
SRT 3 SRTAS030001 |
1-1/4" 1-3/8" 1-1/2" 1-5/8" |
SRTAS030003 SRTAS030005 SRTAS030007 SRTAS030009 |
M33 M36 M39 M42 |
SRTAS030011 SRTAS030012 SRTAS030013 SRTAS030014 |
145945 (66.2) |
660 | 6.82 | 4401 | 11.9 | 5.4 |
SRT 4 SRTAS040001 |
1-1/2" 1-5/8" 1-3/4" 1-7/8" 2" |
SRTAS040004 SRTAS040006 SRTAS040008 SRTAS040010 SRTAS040012 |
M39 M42 M45 M48 |
SRTAS040014 |
223546 (101.4) |
1000 | 10.34 | 6668 | 18.5 | 8.4 |
SRT 5 SRTAS050001 |
2" 2-1/4" 2-1/2" 2-3/4" |
SRTAS050004 SRTAS050006 SRTAS050008 SRTAS050010 |
M52 M56 M60 M64 M68 |
SRTAS050012 |
331372 (150.5) |
1500 | 15.50 | 10003 | 30.4 | 13.8 |
SRT 6 SRTAS060001 |
2-3/4" 3" 3-1/4" 3-1/2" |
SRTAS060004 SRTAS060006 SRTAS06000 8SRTAS060010 |
M72 |
SRTAS060014 SRTAS060016 SRTAS060018 SRTAS060020 SRTAS060022 |
553134 (250.9) |
2500 | 25.84 | 16671 | 50.7 | 23.0 |
SRT 7 SRTAS070001 |
3-1/2" 3-3/4" 4" |
SRTAS070004 SRTAS070006 SRTAS070008 |
M90 |
SRTAS070010 |
708118 (321.2) |
3200 | 33.06 | 21339 | 70.5 | 32.0 |
QUICK REACTION SUBSEA TENSION
Our Subsea bolt tensioner incorporating the quick reaction nut feature reduces diver fatique, improving diver safety and productivity.
Load Cell (Tool Ref) |
Bolt Diameter | Tool Load | Hydraulic Area | Minimum Bolt Protrusion (above nut) |
||||||
---|---|---|---|---|---|---|---|---|---|---|
Imperial | Quick Reaction Nut Number. | Metric | Quick Reaction Nut Number | Ton (short) |
KN | (in2) | (mm2) | (in) | (mm.) | |
SSTAS010001 (SST 1) |
3/4" 7/8" |
QRNAS010001 QRNAS010003 |
M20 M22 |
QRNAS010004 QRNAS010005 |
15.7 | 140 | 1.45 | 934 | 4.09 3.98 |
107 105 |
SSTAS020001 (SST 2) |
1" 1-1/8" |
QRNAS020001 QRNAS020003 |
M24 M27 M30 |
QRNAS020004 QRNAS020005 QRNAS020006 |
27 | 240 | 2.48 | 1600 | 5.24 5.12 |
139 136 134 |
SSTAS030001 (SST 3) |
1-1/4" 1-3/8" |
QRNAS030003 QRNAS030004 |
M33 M36 |
QRNAS030005 QRNAS030006 |
43 | 380 | 3.93 | 2534 | 5.35 5.24 |
142 139 |
SSTAS040001 (SST 4) |
1-1/2" 1-5/8" |
QRNAS040003 QRNAS040004 |
M39 M42 |
QRNAS040005 QRNAS040006 |
62 | 550 | 5.69 | 3668 | 5.94 5.83 5.71 |
160 158 154 |
SSTAS050001 (SST 5) |
1-3/4" 1-7/8" 2" |
QRNAS050001 QRNAS050003 QRNAS050004 |
M45 M48 M52 |
QRNAS050005 QRNAS050006 QRNAS050007 |
99 | 880 | 9.10 | 5868 | 5.94 5.83 5.71 |
160 158 154 |
SSTAS060001 (SST 6) |
2-1/4" 2-1/2" 2-3/4" |
QRNAS060001 QRNAS060003 QRNAS060004 |
M56 M60 M64 M68 M70 |
QRNAS060005 QRNAS060006 QRNAS060007 QRNAS060008 QRNAS060009 |
175 | 1560 | 16.14 | 10411 | 6.54 6.30 6.06 |
1778 175 172 169 165 |
SSTAS070001 (SST 7) |
3" 3-1/4" 3-1/2" |
QRNAS070001 QRNAS070003 QRNAS070004 |
M76 M80 M85 M90 |
QRNAS070005 QRNAS070006 QRNAS070007 QRNAS070008 |
289 | 2575 | 26.63 | 17176 | 7.13 6.89 6.65 |
195 192 188 184 |
Tensioners have quality designed in with standard features that enhance durability and efficiency to get jobs done faster and safer.
Quality Means Lower Life-Cycle Costs:
Stroke | Max Load | Hydraulic Area | Weight | |||||||
---|---|---|---|---|---|---|---|---|---|---|
Order No. | Metric | Bolt Size Stud Prot. (mm) |
(in.) | (mm) | (lbs. tonf) | (Kn) | (in2) | (mm2) | (lbs.) | (kg) |
WDD1-M30 | M30 | 63-70 | 0.27 | 7 | 52.49 | 467 | 53.60 | 3458 | 14.77 | 6.70 |
WDD2-M33 | M33 | 67-74 | 0.27 | 7 | 63.96 | 569 | 65.33 | 4215 | 16.75 | 7.60 |
WDD3-M36 | M36 | 71-80 | 0.40 | 10 | 75.42 | 671 | 77.03 | 4970 | 20.39 | 9.25 |
WDD4-M39 | M39 | 72-86 | 0.40 | 10 | 90.04 | 801 | 91.93 | 5931 | 24.47 | 11.10 |
WDD4-M42 | M42 | 80-92 | 0.40 | 10 | 104.1 | 926 | 106.27 | 6856 | 27.78 | 12.60 |
WSD1-M30 | M30 | 63-81 | 0.27 | 7 | 52.49 | 467 | 53.60 | 3458 | 14.55 | 6.60 |
WSD2-M33 | M33 | 67-86 | 0.27 | 7 | 63.96 | 569 | 65.33 | 4215 | 16.75 | 7.60 |
WSD3-M36 | M36 | 71-93 | 0.40 | 10 | 75.42 | 671 | 77.03 | 4970 | 19.40 | 8.80 |
WSD4-M39 | M39 | 72-95 | 0.40 | 10 | 90.04 | 801 | 91.93 | 5931 | 24.70 | 11.20 |
WSD4-M42 | M42 | 80-96 | 0.40 | 10 | 104.1 | 926 | 106.27 | 6856 | 26.90 | 12.20 |
For Grade 75 ksi - All Thread Foundation Bolts
Stroke | Max Load | Hydraulic Area | Weight | ||||||||
---|---|---|---|---|---|---|---|---|---|---|---|
Load Cell | Adapter Kit ** |
Bar Size | Stud Prot. (mm) |
(in.) | (mm) | (lbs. tonf) | (Kn) | (in2) | (mm2) | (lbs.) | (kg.) |
WSS1 | WSS1-10 | #10 | 206 | 0.40 | 10 | 52.83 | 470 | 53.95 | 3481 | 12.65 | 5.74 |
WSS1-11 | #11 | 219 | 12.90 | 5.85 | |||||||
WSL1 | WSL1-10 | #10 | 255 | 0.99 | 25 | 52.83 | 470 | 53.95 | 3481 | 19.84 | 9.00 |
WSL1-11 | #11 | 266 | 20.28 | 9.20 |
For Grade 150 ksi - All Thread Foundation Bolts
Stroke | Max Load | Hydraulic Area | Weight | ||||||||
---|---|---|---|---|---|---|---|---|---|---|---|
Load Cell | Adapter Kit ** |
Bar Size | Stud Prot. (mm) |
(in.) | (mm) | (lbs tonf) | (Kn) | (in2) | (mm2) | (lbs.) | (kg.) |
WSS2 | WSS2-125 | 1-1/4" | 226 | 0.40 | 10 | 85.43 | 760 | 87.26 | 5630 | 18.08 | 8.20 |
WSS2-138 | 1-3/8" | 238 | 18.30 | 8.30 | |||||||
WSL2 | WSL2-125 | 1-1/4" | 269 | 0.99 | 25 | 85.43 | 760 | 87.26 | 5630 | 27.12 | 12.30 |
WSL2-138 | 1-3/8" | 280 | 27.34 | 12.40 |
Use to lift machines or as a clamp; spread concrete forms or rebar or preform straightening jobs.
Conforms to ASME B30.1 standard.
High strength alloy steel forged upper and lower jaws on HS2000. Jaws are spring return; retract automatically when pressure is released.
No. HS2000-1ton capacity spreader. Full 2, 000 lbs. capacity at10, 000 psi with 4" spread. Can be "dead-ended" at 4" spread under full load. Needs only 9/16" clearance to engage jaws.
No. HS3000-1 1/2 ton capacity spreader. Full 3, 000 lb. capacity at 10, 000 psi with 11 1/2 spread. Greater than competitive units. Needs only 1 1/4" clearanceto engage jaws. Can be "dead-ended" at 11 1/2" spread at full load.
Testedto conform to ASME B30.1 standard
Order No. |
Capacity |
Max. Spread (in.) |
Oil Capacity (cu. in.) |
Min. Clearance Required |
Weight (lbs.) |
---|---|---|---|---|---|
HS2000 | 1 | 4'' | 0.63 | 9/16'' | 4.8 |
HS3000 | 1 1/2 | 11 1/2'' | 3.50 | 1 1/4'' | 22.0 |
Order No. |
Capacity |
Standard Wedge Type | Weight (lbs.) |
---|---|---|---|
HFS3A | 5 | 60° Sharp | 9.0 |
HFS6A | 10 | 60° Sharp | 18.0 |
Order No. | Optional Wedges |
Min. Flange Opening |
Min Combined Flange Opening |
Pin Dia. (in.) |
|||
---|---|---|---|---|---|---|---|
30'' Thin | 60'' Blunt | 60° sth. |
60° Blunt |
30° | |||
HFS3A | 350823 | 350822 | 1/16'' | 1'' | 1/16'' | 3 1/2'' | 11/16'' |
HFS6A | 350549 | 350550 | 1/16'' | 1 1/2'' | 1/16'' | 6 9/16'' | 13/16'' |
ENS Hydraulic Nut Splitter
Order a cylinder and head to make complete nut splitter. Cylinders are interchangeable with heads within specific size ranges. Each are sold separately.
Cylinder | Head | Range | Approx. Weight |
|||||||
---|---|---|---|---|---|---|---|---|---|---|
Bolt Dia. | Nut A/F | (lbs.) | (kg.) | |||||||
(in.) | Metric | (in.) | (mm.) | |||||||
ENSAS010001 (ENS1) | ENSAS010002 (ENS1-1) | ¾" - 1" | M20 -M27 | 1-1/4" - 1-5/8" | 30 - 41 | 14.8 | 6.7 | |||
ENSAS010003 (ENS1-2) | ¾" - 1-1/4" | M20 - M33 | 1-1/4" - 2" | 30 - 50 | 15.2 | 6.9 | ||||
ENSAS020001 (ENS2) | ENSAS020002 (ENS2-1) | 1-1/8" - 1-1/2" | M30 - M39 | 1-13/16" - 2-3/8" | 46 - 60 | 34.8 | 15.8 | |||
ENSAS020003 (ENS2-2) | 1-1/8" - 1-3/4" | M30 - M45 | 1-13/16" - 2-3/4" | 46 - 70 | 35.3 | 16.0 | ||||
ENSAS030001 (ENS3) | ENSAS030002 (ENS3-1) | 1-3/4" - 2" | M45 - M52 | 2-3/4" - 3-1/8" | 70 - 80 | 92.6 | 42.0 | |||
ENSAS030003 (ENS3-2) | 1-3/4" - 2-1/4" | M45 - M56 | 2-3/4" - 3-1/2" | 70 - 85 | 93.7 | 42.5 | ||||
ENSAS030004 (ENS3-3) | 1-3/4" - 2-1/2" | M45 - M64 | 2-3/4" - 3-1/8" | 70 - 95 | 94.8 | 43.0 | ||||
ENSAS030005 (ENS3-4) | 1-3/4" - 2-3/4" | M45 - M72 | 2-3/4" - 4-1/4" | 70 - 105 | 97.0 | 44.0 | ||||
ENSAS040001 (ENS4) | ENSAS040002 (ENS4-1) | 2-¾" - 3" | M76- M80 | 4-1/4" - 4-5/8" | 110 - 115 | 160.9 | 73.0 | |||
ENSAS040003 (ENS4-2) | 2-¾" - 3-1/2" | M76- M90 |
4-1/4" - 5-3/8" | 110 - 130 | 165.3 | 75.0 |
Aluminum Cylinder Base- For use when an enlarged cylinder base is needed or advantageous. Attaches to bottom of RA556, RA556L, and RA5510 with four 3/8"-16 screws (included). Serrated base for extra stability.
Order No. | Description | Weight (lbs.) |
---|---|---|
208406 | Aluminum 55 Ton Cylinder Base, 7" square. For use with RA556, RA556L, and RA5510 cylinders. |
4.0 |
Puller Accessory converts PH113C into Hydraulic Straightening Tool
Portable.Good for straightening mechanical shafts, round bars, etc. Simply remove pump and cylinder from puller head and insert them into the straightening tool accessory. This product is widely used in steel mills, wire roll companies, wire extruding companies, textile industry, and any straightening situation where portability and power are required. Contoured heat-treated shaft adapter included.
Order No. | Description | Weight (lbs.) |
---|---|---|
HST11 | Spread: 3 1/2" to 16 1/8", Reach: 5 29/32" | 21.0 |
Metric Adapters
Add metric capability to your Push-Puller legs or forcing screws! Four separate metric kits available with a variety of sizes for your Push-Puller legs or forcing screws! Each packaged in a convenient plastic organizer case.
CAUTION:All the items shown may not withstand the full tonnage of the pullers they may be used with.
Metric Adapters
Order No. |
Female End (in.) |
Male End | Length (in.) |
Weight (lbs.) |
---|---|---|---|---|
8111 | 5/8" - 18 | M6 x 1.0 | 2 1/4" | 3.0 |
8112 | 5/8" - 18 | M8 x 1.0 | 2 1/4" | 3.0 |
8113 | 5/8" - 18 | M8 x 1.25 | 2 1/4" | 3.0 |
8114 | 5/8" - 18 | M10 x 1.25 | 2 1/4" | 3.0 |
8115 | 5/8" - 18 | M10 x 1.50 | 2 1/4" | 3.0 |
8116 | 5/8" - 18 | M12 x 1.25 | 2 1/4" | 3.0 |
8117 | 5/8" - 18 | M12 x 1.75 | 2" | 3.0 |
8121 | 5/8" - 18 | M14 x 1.5 | 2 1/4" | 3.0 |
8122 | 5/8" - 18 | M14 x 2.0 | 2 1/4" | 3.0 |
8123 | 5/8" - 18 | M16 x 1.5 | 2 3/4" | 3.0 |
8124 | 5/8" - 18 | M16 x 2.0 | 2 3/4" | 3.0 |
8125 | 5/8" - 18 | M20 x 1.5 | 2 3/4" | 3.0 |
8126 | 5/8" - 18 | M20 x 2.5 | 2 3/4" | 3.0 |
Power Team step plate adapters are necessary for pulling and installing bearings, gears, or other parts on hollow shafts or housings. Puller screw forces against step plate adapter, as shown at right. May be used with Power Team jaw-type pullers, Push-Pullers and shop presses.
CAUTION:All the items shown may not withstand the full tonnage of the pullers they may be used with.
USED WHERE SPACE DOES NOT PERMIT HOOKING PULLER JAWS DIRECTLY ON PART TO BE PULLED.
Meets Fed. Spec.: GGG-P-00781-D
Pulling attachment accessory (No. 1128)
Order No. | Application - Used with Puller Numbers | Weight (lbs.) |
---|---|---|
1121 | 1020, 1022, and 1023. | 12 oz. |
1122 | 1024, 1025, 1026, 1027, 7392 and 7393. | 1 lb., 4 oz. |
1123 | 1035, 1036, 1037, 1038, and 927. | 5 lbs. |
1124 | 1035, 1040, 1041, 1042, PH172, PPH17, and 938. | 12 lbs. |
1126 | 939, 1043, and 1047* | 19 lbs., 12 oz. |
1127 | 939, 1047*, PH302*, and PPH30* | 41 lbs., 12 oz. |
1128 | PH302*, PH502*, PH553C, and PPH50. (When using 1128 with PPH50, two8024 adapter are required to connect PPH50 to the puller tees.) | 100 lbs. |
1130 | 1035, 1040, 1041, 1042, PH172, PPH17, and 938. | 12 lbs., 9 oz. |
V-belt pulley pulling attachments | ||
679 | 1035, 1036, 1037, 1038, and 927. | 4 lbs., 4 oz. |
680 | 1039, 1040, 1041, 1042, 1047*, PH172, PPH30* and 938. (When using 680 with PPH30, two 8012 adapters are required.) |
22 lbs., 4 oz. |
* Indicates discontinued puller model. |
Rugged industrial strength material, strong as stell, never needs painting, won't rust, dent or chip.
Weatherproof lid is self sealing and lockable.
Molded-in handles, water-tight, one piece bottom and side construction. Strong enough to stand on.
Note: Actual product may differ from photo.
Order No. | Length (in.) |
Height (in.) |
Width (in.) |
Weight (lbs.) |
---|---|---|---|---|
350722 | 35 | 14 | 13 1/2 | 23.0 |
Convert Power Team Shorty RSS Seriescylinders to mechanical cribbing devices; more stable than timber or other awkward, makeshift methods. Ideal for lifting applications such as structure moving. Reduces cribbing time dramatically. In effect, increases the stroke of the cylinder; stacking pads act as cylinder extensions:
Order No. | Description | Weight (lbs.) |
---|---|---|
CB30 | Cribbing block set for use with No. RSS302; 30 ton cylinder | 21.0 |
CB50 | Cribbing block set for use with No. RSS502; 50 ton cylinder. | 29.3 |
CB100 | Cribbing block set for use with No. RSS1002; 100 ton cylinder. | 66.2 |
45589 | Insertion handle is used for inserting rings and pads. | 1.3 |
For Use With | 30 Ton Cylinder No. RSS302 | 50 Ton Cylinder No. RSS502 | 100 Ton Cylinder No. RSS1002 | ||||||
---|---|---|---|---|---|---|---|---|---|
Order Number | 30 Ton Set No. CB30 | 50 Ton Set No. CB50 | 100 Ton Set No. CB100 | ||||||
Lower Ring |
Upper Ring |
Stacking Pad |
Lower Ring |
Upper Ring |
Stacking Pad |
Lower Ring |
Upper Ring |
Stacking Pad |
|
No. included in set | 1 | 2 | 3 | 1 | 2 | 3 | 1 | 3 | 4 |
Outside Diameter (in.) | 4 1/2 | 4 1/2 | 2 3/4 | 5 1/2 | 5 1/2 | 3 3/8 | 7 25/64 | 7 25/64 | 4 3/4 |
Inside Diameter (in.) | 2 13/16 | 2 13/16 | –– | 3 29/64 | 3 29/64 | –– | 4 13/16 | 4 13/16 | –– |
Height, each (in.) | 2 9/32 | 1 51/64 | 1 25/32 | 2 7/32 | 1 23/32 | 1 11/16 | 2 1/8 | 1 3/4 | 1 23/32 |
Total stacked height of rings in Set (in.) | 5 7/16 | 5 3/16 | 6 7/8 | ||||||
Weight of Set (lbs.) | 20 | 28 | 64 | ||||||
* Each set includes one Insertion Handle No. 45589 - 1/2'' Hex. x 18'' Long, 4'' Bend |
Order No. | Face Dia. | psi/Bar | Tons | Major Graduations | Minor Graduations | Silcone Filled | Use with Cylinder Series |
---|---|---|---|---|---|---|---|
9040 | 2 1/2" | 0-10,000/ 0-690 |
– | 2500 psi, 100 Bar |
500 psi, 20 Bar |
Yes | All |
9041 | 2 1/2" | 0-10,000/ 0-690 |
– | 2500 psi, 100 Bar |
500 psi, 20 Bar |
No | All |
9051 | 4" | 0-10,000/ 0-690 |
– | 1000 psi, 100 Bar |
200 psi, 10 Bar |
No* | All |
9052 | 4" | 0-10,000/ 0-690 |
– | 1000 psi, 100 Bar |
200 psi, 10 Bar |
Yes | All |
9059 | 4" | 0-10,000/ 0-690 |
0-17.5, 0-30 and 0-50 |
2000 psi, 5 Ton |
200 psi, .5 Ton on 30, 50 Ton Scales; .2 Ton on 17.5 Ton Scale |
No* | RT172, RT302, RT503 |
9053 | 4" | 0-10,000/ 0-690 |
0-5 | 2000 psi, 1 Ton |
200 psi, .1 Ton |
No | C & RLS |
9055 | 4" | 0-10,000/ 0-690 |
0-10 | 2000 psi, 1 Ton |
200 psi, .1 Ton |
No* | C, RD, RH, RLS & RSS |
9063 | 4" | 0-10,000/ 0-690 |
0-25 | 2000 psi, 5 Ton |
200 psi, .5 Ton |
No* | C & RD |
9065 | 4" | 0-10,000/ 0-690 |
0-30 | 2000 psi, 5 Ton |
200 psi, .5 Ton |
No* | RH†, RLS & RSS |
9067 | 4" | 0-10,000/ 0-690 |
0-50 | 2000 psi, 5 Ton |
200 psi, .5 Ton |
No* | RH†, RLS & RSS |
9069 | 4" | 0-10,000/ 0-690 |
0-55 | 2000 psi, 5 Ton |
200 psi, .5 Ton |
No* | C, R, RA & RD |
9071 | 4" | 0-10,000/ 0-690 |
0-60 | 2000 psi, 5 Ton |
200 psi, 1 Ton |
No* | RH |
9075 | 4" | 0-10,000/ 0-690 |
0-100 | 2000 psi, 10 Ton |
200 psi, 1 Ton |
No* | C, R, RA, RD, RH, RLS†, RSS† & RT1004† |
9077 | 4" | 0-10,000/ 0-690 |
0-150 | 2000 psi, Initial 10 Then 20 Ton |
200 psi, 2 Ton |
No* | C, R, RD & RLS |
9079 | 4" | 0-10,000/ 0-690 |
0-200 | 2000 psi, 20 Ton 10 Then 20 Ton |
200 psi, 2 Ton |
No* | R, RD & RH† |
9089 | 6" | 0-10,000/ 0-690 |
1000 psi, 100 Bar |
100 psi, 10 Bar |
No* | All | |
* Shipped “dry.” User can convert to “wet” using liquid silicone No. 9046. † The tonnage scale on the gauge may vary slightly among different series cylinders due to different effective area. |
The following remote control switches will give you momentary ON control of your hydraulic pump. These switches are deadman type, spring loaded to the OFF position. They can be used with any Power Team electric hydraulic pump.
Order No. | Description | Weight (lbs.) |
---|---|---|
10461 | Remote foot control, with 10 foot cord. | 3.0 |
25017 | Remote hand control. Has a push button switch, with a 10 foot cord. | 0.8 |
203225 | Remote hand control. Heavy-duty with single push button switch in a neoprene housing with 10 foot cord. Housing seals out dust, lint and liquids (unit is not submersible). | 0.8 |
251660 | Remote foot control, with 10 foot cord. For use with the PE10 style pumps. | 1.0 |
Make your Power Team press even more versatile with one of these accessory sets. These sets will eliminate makeshift set-ups. Many of these items can be used with pullers you already have.
A | B | C | D | E | F | G | |||
---|---|---|---|---|---|---|---|---|---|
Order No. | Use With Press: |
V-Throat Press Plate |
V-Blocks | Pushing Adapter ‡ | Pushing Adapter ‡ | V-Pushing Adapter |
Single-Acting Cyls. | Double-Acting Cyls. | Pushing Adapter |
SPA10 | 10 Ton | 1888 | 1890 (Pr.) | 201923† 1/2" dia. shank |
201454† 3/4" dia. shank | 34806† | Included in Set | ||
38597 | 38597 | ||||||||
SPA25 | 25 Ton | 1889 | 1891 (Pr.) | 34510† 3/4" dia. shank |
34511† 1" dia. shank |
34807† | Included in Set | ||
38953 | 38953 | ||||||||
SPA55 | 55 Ton | — | 1892 (Pr.) | 34755 1" dia. shank |
34756 1 1/2" dia. shank |
34808 | Not Included Order Separately |
||
37368 | 38954 | ||||||||
SPA100 |
80/100 Ton |
— |
1893 ** (Pr.) |
— |
— |
36469 |
Not Included Order Separately |
21332 |
|
43562 46070 *** |
43563 46070 |
||||||||
SPA200 | 150/200 Ton | — | 207395 (Pr.) |
— | 44458 2 1/4" dia. shank |
44457 | None* | — | |
* Pushing adapters thread directly into RD15013 and RD20013 cylinders. ** V-blocks, No. 1893, are recommended for use with 80-ton Roll-Bed® press. Not recommended for use with 100-ton Roll-Bed® press. *** For 80-ton Roll-Bed® press. † Also, an Optional Accessories for use with CC5, CC10 & CC25 Hydraulic Clamps NOTE: Individual press accessories may be ordered separately. ‡ CAUTION: Pushing adapters are designed for use with specific shaft sizes, and depending on the condition of the shaft ends, the adapter may not withstand the full press tonnage. Always use a protective blanket or other suitable guard when pressing. |
This remote hand control has two momentary push buttons, one for advance and one for retract with spring offset to hold. To be used with 4-way/2-position air pilot valves.
Order No. | Description | Weight (lbs.) |
---|---|---|
209593 | Remote hand control with 12 foot cord. | 2.0 |
This remote hand control has two momentary push buttons, one for advance and one for retract with spring offset to hold. To be used with 4-way/2-position air pilot valves. |
Non-conductive hose
For applications requiring electrical isolation by the hose, non-conductive hose has a leakage factor of less than 50 microamperes, considered a safe level of conductivity by SAE standards. The covering is polyurethane and colored orange for easy identification as nonconductive hose. The covering is not perforated, preventing moisture from entering the hose and affecting its overall conductivity. All non-conductive hoses have a minimum burst pressure of 40, 000 psi.
BE SAFE!
Order No. | Hose Type | Couplers/Fitting | Inner Diameter (in.) |
Length (ft.) |
Burst Rating |
---|---|---|---|---|---|
9773 | Non-Conductive | 3/8" fitting NPTF | 1/4 | 6 | 40,000 psi |
9774 | Non-Conductive | 3/8" fitting NPTF | 1/4 | 10 | 40,000 psi |
9775 | Non-Conductive | 3/8" fitting NPTF | 1/4 | 20 | 40,000 psi |
2000351 | 3/8" fitting NPTF | 1/4 | 15 | ||
2000350 | 3/8" fitting NPTF | 1/4 | 25 | ||
3-3944* | Male/Male Couplers† | 1/4 | 6 | ||
3-3945* | Male/Male Couplers† | 1/4 | 10 | ||
3-3946* | Male/Male Couplers† | 1/4 | 15 | ||
3-3947* | Male/Male Couplers† | 1/4 | 25 | ||
3-3956* | Male/Female Couplers† | 1/4 | 6 | ||
3-3957* | Male/Female Couplers† | 1/4 | 10 | ||
3-3958* | Male/Female Couplers† | 1/4 | 15 | ||
3-3959* | Male/Female Couplers† | 1/4 | 25 | ||
* Hoses are prefilled with hydraulic fluid |
rder No. | Description | Weight (lbs.) |
---|---|---|
DG100* | Digital pressure gauge, pressure range 0-10,000 psi. | 2.3 |
DG100B* | Digital pressure gauge, pressure range 0-700 bar. | 2.3 |
* Note: Serviced only at factory. |
Mobilize your hydraulic pumps with the PC200. The rugged tubular frame can easily handle pumps weighing up to 200 lbs. With 12" wheels, the cart rolls easily. Just load the pump onto the cart and wheel it right to the job. The universal mounting hole pattern lets you handle a wide variety of Power Team pumps.
Used on these pumps:PA60, PA64and PA554 air/hydraulic pumps; PE55 series, PE183-2 and PE184-2 electric/hydraulic pumps; PE21, PQ60 and PQ120 series Quiet pumps; PG55 series gas engine/hydraulic pumps; and pumps with optional 5 and 10-gallon reservoirs; Nos. RP50, RP51, RP101 and RP103.
Order No. | Description | Weight (lbs.) |
---|---|---|
PC200 | Universal pump cart with 12" wheels. | 27.0 |