Tsisco Industrial Ltd.

We provide: 1. Main products:hot rolled bars, peeled bars, cold forged bars, cd bars(round bars, square bars, hex bars), cg bars 2. Greades:303, 303cu, 304/l, 316/l, 310s, 321, 410, 420, 416, 17-4ph, 201cu, 3. Size(mm):15 / 16 / 18 / 20 / 22 / 25 / 28 / 30 / 32 / 35 / 40 / 45 / 50 / 55 / 60 / 65 / 75 / 90 / 105 / 125 / 130 / 150 / 200 /240 / 250 / 300 4. Length(mm):2000-7500 5. Standard:gb jis astm en din

We provide: 1. Hrap wire rods for thin wire and super-thin wire: size: φ5.5mm delivery conditions: hrp, hrap, hr+solution allealing+pickling coil weight: 700kgs to 1400kgs; other weight will be delivered upon negotiation. 2. Hrp wire rods for welding materials size: φ5.5~8.0mm delivery conditions: hrp, hrap, hr+solution allealing+pickling coil weight: 700kgs to 1400kgs; other weight will be delivered upon negotiation. 3. Wire rods for cold heading size: φ5.5~20.0mm delivery conditions: hrp, hrap, hr+solution allealing+pickling coil weight: 700kgs to 1400kgs; other weight will be delivered upon negotiation.

We provide: 1. Electro polishing quality (epq) wire 2. Weaving wire, braiding wire 3. Cold heading wire 4. Spring wire 5. Redrawing, annealing wire 6. Shaped wire 7. Welding wire

We are offering Stainless Steel Welded Pipes and Stainless Steel Welded Tubes. we provide: 1. general specifications size: o.d.9.9mm to o.d. 2000mm; w.t. 0.4mm to 25mm. application: chemical, pulp, water treat, food, automobile, oil & gas, petrochemical equipment, onshore and offshore poject. standards: gb, astm, jis, astm a789, astm a790 materials: 304, 304l, 316, 316l, 31803, 32750, 32760, 32205 2. stainless steel pipe: astm a312, astm a358, astm a778 3. large diameter stainless steel pipe(o.d. can be made up to 80"): astm a312, astm a358, astm a409, cns 13517 g3259, jis g3468 4. stainless steel tube for boiler, heat-exchanger and feedwater heater: astm a249, astm a269, astm a688, cns 7383 g3142, jis g3463 5. stainless steel mechanical tube: astm a554, cns 5802 g3119, jis g3446.

We are offering stainless steel precision tubing & bright annealing tubes. we provide: fuel rail tubing: 1.4301 en 10216 - 05 od tolerance: +/- 0.08, +/-0.05mm wt tolerance: -0/+10% ra ≤ 6.3 um

We are offering stainless steel hollow bars. we provide: standards: din17458, din17456, en 10216, en10088, astm276 materials: 304/304l, en 1.4301/1.4307, 316/316l, en 1.4401/1.4404

We are offering stainless steel u tubes. we provide: 1. Standards: astm a 213, asme sa 213, astm a 249, asme sa 249, astm a 688, asme sa 688, astm a 789, asme sa 789, astm b 163, asme sb 163, astm b 167, asme sb 167, astm b 668, asme sb 668 2. Materials: 304/l/h, 316/l/ti, 317/l, 321/h, 347/h, 310s, s31500, s31803, s32205, s32750, s32760, s32001, s32304, n06600, n06625, n08800, n08810, n08811, n08825, n08904, n04400, ti gr.1/gr.2 3. Heat treatment: if specified, we are equipped to carry out heat treatment of bends plus min. 150 mm of leg. - furnace is computer controlled and all data is recorded. - we use an argon protective atmosphere inside the tubes. - we can provide all types of annealing: solution; stress relieving; stabilization 4. Technical parameters: od 12.7-38 mm bending radii from 1.5xod up to 1250 mm. Minimum bending radii for od's over 28 mm after agreement. leg length min. 1, 000 mm leg length max. 12, 000 mm heat treatment for radii up to 1, 000 mm 5. Technical standards for bending: other specifications or special requirements available upon request. Copies of common standard specifications are available on request. 6. Hydrotesting: - after heat treatment all u-tubes are hydrotested. - minimum holding time at the required pressure is 5 sec. - all tubes are dried and carefully cleaned after testing. 7. Measuring, cutting, deburring, cleaning: - u-bends are measured exactly in accordance with relevant standards, or to customer's specification. - all tubes are cut to the specified leg lengths, ends are deburred and the tubes are internally cleaned with air. - before packing, both ends are capped with plastic caps.

We are offering Stainless Steel Seamless Pipes and Stainless Steel Seamless Tubes. we provide: 1. main steel types and typical grades: austenite: 301, 310s, 304, 304l, 304h, 316, 316l, 316ti, 317, 317l, 321, 321h, 347h, 904l duplex: s31803, s32205, s31500, s31750, s31760, s31900, s32304 incoloy: 800, 800h, 800ht, 825, 901, 925, 926 2. main production standard: en 10216-5, en 10216-2, din 17456, din 17458, a213, a269, a511, a789, a790, a335, a376, sa213, sa312, sa789, sa790, sa335, sa376, sb161, sb163, sb167, sb338, sb668, sb677, jis g3459, g3463, gb/t 14975, t14976, gb13296, gb5310, gb9948 3. products: stainless steel seamless pipes & tubes(cold drawn, cold rolled, bright precision) diameter(mm):6-830 thickness(mm):0.8-45 length(m):max: 240