Jinan Should Shine Import and Export Co. Ltd.

• MOQ 2 Set(s)

We are offering za3130 automatic transmission training system i. Overview technical teaching equipment, vechile trainer, automobile training equipment to university, college, technical schools, training institute. Transmission vehicle model: volkswagen transmission model: 01m working voltage :220v380v equipped with leakage protector frequency:5060hz, power:220v-350w380v-3000w　　　 inverter: power: 4kw5.5kw input: ac 3ph 380v±15% output: 9a13a ac3ph 0~380v 0~400hz dimension: 1400×1000×1750 (l×w×h) the whole rack uses international standard square tube, angle iron is with seamless welding, surface is under high temperature spray treatment after polishing, it is anticorrosive and anti-aging, does not fade, etc., the bottom of the rack is equipped with universal self-locking casters, convenient for the rack movement teaching. Control panel with pure aluminum plate (4mm thickness), control panel is painted with color and intuitive volkswagen 01m automatic transmission schematic which is consistent with the original vehicle control system, and with manual and experiment guide books. Volkswagen 01m automatic transmission assembly, automatic transmission control unit, shift lever assembly, transmission oil cooling device, the combination meter, three-phase adjustable-speed motor, inverter, throttle body assembly, engine crankshaft sensor and signal plate, diagnostic seat, pressure gauge, fault setting system, the original car circuit diagram board and testing terminals, mobile rack and so on. It is equipped with task-drive teaching model training instruction and bench operating instruction book. Each sensor and actuator is installed with digital display meters, the rack is installed with oil duct pressure gauge, universal locking casters and stainless steel hand guard, protective devices are installed on the rack where is with high temperature and on the rotating parts.

• MOQ 1 Set(s)

Za3136 motorcycle lift 2 strokes teaching model i. Overview technical teaching equipment, vechile trainer, automobile training equipment to university, college, technical schools, training institute. Dimension: 1300×1000×1900(l×w×h) operating environment: temperature-40℃～40℃, humidity≤80% engine type: motorcycle engine engine oil level: api (american petroleum institute) standard sg level, accumulator: maintenance-free battery the whole rack uses international standard square tube , the tube dimension is 40*40*2mm thickness , angle iron is with seamless welding, surface is under high temperature spray treatment after polishing, it is anticorrosive and anti-aging, does not fade, etc., the bottom of the rack is equipped with universal self-locking casters, convenient for the rack movement teaching. Control panel with pure aluminum plate, control panel is painted with color and intuitive electronic control system schematic which is consistent with the original vehicle control system, and with manual and experiment guide books. With engine: 2 stroke motorcycle engine 100-125cc instrument: secret key type ignition switch, subsystems: air cooling system, with 1l tank capacity fuel system, electrical system: headlights, rear lights, continuous lights & signal lights ignition: cdi system has a complete color circuit schematic panel, external detection terminals, intelligent fault setting box assembly, removable stand, manual and experiment guide book.

• MOQ 2 Set(s)

We are offering za3124 four cylinders diesel training stand i. Overview technical teaching equipment, vechile trainer, automobile training equipment to university, college, technical schools, training institute. Dimension: 650×650×1150（l×w×h） operating environment: temperature -5℃～40℃, humidity≤80% engine type: vw engine model: jetta sdi（original engine） displacement: 1.6l working voltage: 220v equipped with leakage protection switch frequency: 5060hz power: 200w the complete rack use square tube and angle iron of international standardized profile to conduct seamless welding, its surface is dealt with high temperature spraying plastics after polishing, which is anti-corrosion, anti-aging and fastness, it is installed with universal self-locking castor on the bottom of the rack, which is convenience to teach movably. It uses loading motor to be power source which drive the motor run smoothly. Teaching function: we can use the device to understand the consist of electronic control gasoline engine mechanical system, the appearance of each component and the connected relation between each component, which can deepen students, understanding of the composition and working principle of the engine mechanical system and help students understand the abstract control theory. Main training project: knowing the construction and working principle of crank connecting rod mechanism of electronic control gasoline engine. Knowing the construction and working principle of valve mechanism. Knowing the construction and working principle of ignition system. Knowing the construction and working principle of fuel oil supply system. Knowing the construction and working principle of cooling system. Knowing the construction and working principle of lubrication system.

• MOQ 1 Set(s)

We are offering za3135 automatic transmission teaching stand i. Overview technical teaching equipment, vechile trainer, automobile training equipment to university, college, technical schools, training institute. Size 950×650×1200（l×w×h） operating environment temperature:-40℃～40℃, humidity ≤80% transmission type :volkswagen transmission model :lavina working voltage :220v matched leakage protector frequency :5060hz power ;200w overall bench adapt international standard square tube , angle iron seamless welding, after the surface polishing grinding, then the surface is dealt with high temperature spraying plastics , it can anti-corrosion and anti-aging , hardly lose it’s color, at the bottom of the bench is equipped with universal self-locking castor for mobile teaching .on the basis of the volkswagen lavina automatic transmission entity to fully cut away the automatic transmission , use the different color distinguish all the gear can be observed .a it is suitable for the auto automatic transmission construction and maintenance of higher vocational colleges and training institutions , it can satisfy the teaching requirement of auto automatic transmission structure , working principle visual display .this experiment equipment operation conveniently , safe and reliable , it is easy to maintain.

• MOQ 2 Set(s)

We are offering za3129 front wheel drive manual transmission model. I. Overview technical teaching equipment, vechile trainer, automobile training equipment to university, college, technical schools, training institute. Dimension: 1000×650×1600（l×w×h） operating environment: temperature-5℃～40℃, humidity≤80% transmission type: santana working voltage: 220v equipped with leakage protector frequency: 5060hz power: 200w the rack use square tube and iron plate of international standardized profile to conduct seamless welding, its surface is dealt with high temperature spraying plastics after polishing, which is anti-corrosion, anti-aging and fastness, it is installed with universal self-locking castor on the bottom of the rack, which is convenience to teach movably. Using full dissection of santana transmission, you can observe all the gears that are painted with different colors for distinguishing. Using gear motor as dynamical system and using it to drive the primary shaft of transmission running slowly, it can turn to different gears, you can observe transmission between each internal gear through cut away structure. It is equipped with a matched operation and maintenance manual. Supply english user manual.

• MOQ 1 Set(s)

We are offering za3134 manual transmission educational aids i. Overview technical teaching equipment, vechile trainer, automobile training equipment to university, college, technical schools, training institute. A.manual transmission 5 speed b.to identify the function and work principle of manual transmission system c.all components can be operation, adopts original car components d.include the function and system of automatic transmission system e.original components sectioned and color paint, so students can recognize the components structure clearly

• MOQ 2 Set(s)

We are offering za3126 diesel engine cutting model with electrical motors movement i. Overview technical teaching equipment, vechile trainer, automobile training equipment to university, college, technical schools, training institute. Dimension: 650×650×1150（l×w×h） operating environment: temperature -5℃～40℃, humidity≤80% engine model: motorcycle working voltage: 220v equipped with leakage protection switch frequency: 5060hz the complete rack use square tube and angle iron of international standardized profile to conduct seamless welding, its surface is dealt with high temperature spraying plastics after polishing, which is anti-corrosion, anti-aging and fastness, it is installed with universal self-locking castor on the bottom of the rack, which is convenience to teach movably. It uses loading motor to be power source which drive the motor run smoothly. Teaching function: we can use the device to understand the consist of electronic control gasoline engine mechanical system, the appearance of each component and the connected relation between each component, which can deepen students, understanding of the composition and working principle of the engine mechanical system and help students understand the abstract control theory. Main training project: knowing the construction and working principle of crank connecting rod mechanism of electronic control gasoline engine. Knowing the construction and working principle of valve mechanism. Knowing the construction and working principle of ignition system. Knowing the construction and working principle of fuel oil supply system. Knowing the construction and working principle of cooling system. Knowing the construction and working principle of lubrication system.

• MOQ 2 Set(s)

We are offering zm2146 heterogeneous separation experiment apparatus i.technical parameters 1. Fan blast capacity: 2800rpm, blast capacity 450 m3h wind pressure 120mmh2o, efficiency 66%, axis rate0.75kw. 2. Particle silica gel: 60-80μm. 3. Dedusting efficiency: η20≥98%. 4. Separate ability: ≥8lh. 5. Whirlwind separator, dust-settling compartment, feeder: is made of transparent organic glass. 6. Receiving flask is made of transparent organic glass. 7. Structure is stainless steel, structure is compact, flow is easy. 8. Dimension: 1000×500×1600mm. I.experiment purpose 1. Observe airflow which contains dust function condition under the power of whirlwind separator. 2.understand heterogeneous separation experiment principle. 3.to understand gas and solid separation rate efficiency to different particle size test 4.test heterogeneous separation experiment data.

• MOQ 1 Set(s)

We are offering za3146 brake abs training stand. I. Overview technical teaching equipment, vechile trainer, automobile training equipment to university, college, technical schools, training institute. Size 1300×1000×1800（l×w×h） operating environment temperature:-5℃～40℃, humidity ≤80% abs type svw abs abs mode gsi overall bench adapt international standard square tube , angle iron seamless welding, after the surface polishing grinding , then the surface is dealt with high temperature spraying plastics , it can anti-corrosion and anti-aging , hardly lose it’s color, at the bottom of the bench is equipped with universal self-locking castor for mobile teaching . Detection board adapt the pure aluminum-plastic panel, on the detection panel with perceptual intuition electric control system schematic diagram, and the color is consistent with the original car control system , and it is equipped with operation specification and experiment guidbook , etc . Product content : it’s equipped with original component , including electric control unit , hydraulic control unit , wheel speed sensor , brake pedal , brake master cylinder , vacuum booster tank , brake disc , brake caliper , braking line , diagnose interface, system and general fault control board , test board , with whole color circuit principle diagram board , mobile bench , operation specification and experiment guidbook .

• MOQ 2 Set(s)

We are offering za3128 charging teaching model. i. Overview technical teaching equipment, vechile trainer, automobile training equipment to university, college, technical schools, training institute. Car model: "superman of the times" of santana 　　generator voltage: 14v working voltage: 220v, 380v equipped with leakage protection switch frequency: 5060hz power: 350w750w demonstrator size: 1200×1100×200（l×w×t） storage cabinet standard: 1600×3500×700（l×w×h）（standard configuration table） the complete rack use square tube and angle iron of international standardized profile to conduct seamless welding, its surface is dealt with high temperature spraying plastics after polishing, which is anti-corrosion, anti-aging and fastness, it is installed with universal self-locking castor on the bottom of the rack, which is convenience to teach movably. The control panel used aluminum-plastic panel, it is painted with colorized intuitive charging system schematic diagram that is the same with the original car control system on the panel, and it is also equipped with operating manual and experiment instructor. Product formation: equipped with original car parts, include general equipment fault control panel, such as ignition lock, each part of generator and system. Test panel is equipped with complete colorized schematic circuit diagram panel, movable rack, operating manual and experiment instructor. This demonstrator takes new ac motor of vw as prototype, which has certain representativeness. It reflects the internal construction of generator and circuit components clearly, there are separate parts of generator which are arranged on the upper part of the demonstrator, and there is colorized principle diagram of charging system on the bottom part of the demonstrator, it installed with a generator who runs normally, and connect engine integrating block terminal to teaching board diagram terminal with electrical wire.

• MOQ 1 Set(s)

We are offering zm2148 heat transfer experiment apparatus i.technical parameters 1.tube heat exchanger: inner tube ф22x1.5mm, external tube ф52x1.5mm, heat exchange length:1.0m. 2. Vapor generator: stainless material, heating power: 2kw, operate voltage 220v. 3. Pump: centrifugal middle pressure fan, power: 250w, rotary speed: 2800min, wind presssure:1300pa, blast capacity:8m3min. 4. Pressure measurement range:0-2.5mpa, accuracy: 0.5 class, temperature test range:-50 - 150℃, accuracy class 0.5 class. 5.thermal ball anemograph: measure wind speed:0.05-10ms, rotor flow meter: measure range:4-40 m3h. 6. Experiment tube, valve is stainless and copper structure. 7.frame is stainless, structure is compact, flow is easy, operation is easy. 8.dimension:1500×550×1700mm. I.experiment purpose 1. Be familiar with heat transfer experiment design project and flow design. 2. To understand heat exchanger basic structure and principle. 3. Master heat calculation and heat constant k to convection current heat-transfer film α measurement method. 4. To understand heat route affect on heat constant.

• MOQ 2 Set(s)

We are offering za3125 gasoline engine cutting model with electrical motors movement i. Overview technical teaching equipment, vechile trainer, automobile training equipment to university, college, technical schools, training institute. Dimension: 650×650×1150（l×w×h） operating environment: temperature -5℃～40℃, humidity≤80% engine model: motorcycle engine working voltage: 220v equipped with leakage protection switch frequency: 5060hz the complete rack use square tube and angle iron of international standardized profile to conduct seamless welding, its surface is dealt with high temperature spraying plastics after polishing, which is anti-corrosion, anti-aging and fastness, it is installed with universal self-locking castor on the bottom of the rack, which is convenience to teach movably. It uses loading motor to be power source which drive the motor run smoothly. Teaching function: we can use the device to understand the consist of electronic control gasoline engine mechanical system, the appearance of each component and the connected relation between each component, which can deepen students, understanding of the composition and working principle of the engine mechanical system and help students understand the abstract control theory. Main training project: knowing the construction and working principle of crank-link mechanism of electronic control gasoline engine. Knowing the construction and working principle of valve mechanism. Knowing the construction and working principle of ignition system. Knowing the construction and working principle of fuel oil supply system. Knowing the construction and working principle of cooling system. Knowing the construction and working principle of lubrication system.

• MOQ 2 Set(s)

We are offering zm2147 fluidized bed desiccation experiment apparatus i.technical parameters 1.air peripheral pump: blast capacity450 m3h, wind presssure, 120mm h2o, efficiency 66%, shaft power 0.75kw. 2. Electric heating case: power 2kw, stainless material. 3.u type differential pressure gauge: measure fluidized bed total differential pressure and inlet wind flow. 4. Electric control case: in electric control console, there installed intelligent temperature control meter, to test dry room inlet and outlet temperature, power switch, fan switch, press rotary button, the corresponding work start. 5. Experiment bench frame and control panel use stainless material, structure is beautiful, flow is easy, operation is easy. 6.dimension:1500×600×2000mm. I.experiment purpose 1. To learn fluidized bed dry structure, flow and operation method. 2. Learn to test material feature under dry condition, research fry condition affect on dry process. 3. Master using experiment curve get dry speed rate, and constant speed stage dry rate, critical moisture content, equilibrium moisture content experiment method.

• MOQ 1 Set(s)

We are offering zp6116 silk wire mesh dryers i. Introduction  fan with forced convection and natural convection function, it meets different experiment function.  usage: it is for drying silk wire mesh plate ink.  capacity: it can preset dryer temperature and display it, with temperature adjust function. temperature range: r.t~300℃ temperature natural convection:±0.5℃ max temperature: 20min temperature departure:±3℃ temperature display mode: measurement and setting temperature digital display temperature sensor: industrial resistor(pt100) shell material: rust-proof treatment cold-roll steel sheets electrostatic spray inner material: galvanized sheet inner door: thermo stability toughened glass thermal insulation material: agm door seal: environmental silicon rubber bar heater: nickel-chromium electric heater inner box dimension:d1000mm×w800mm×h1000mm power: 4kw power supply: ac 220v, 50hz

• MOQ 1 Set(s)

We are offering zm2134 methods flowmeter apparatus i.technical parameters 1.water pump: maximum fluid 30lmin. Top lift 16m. Power 370w. Work voltage 220v. Rotary speed 2850rmin 2.hole plate diameter: do=8mm, stainless material. 3. Venturi tube throat diameter: dv=8mm, stainless material. 4.metering sink volume: 15l, storage water tank volume: 20l. 5. Experiment all fluid—water design cycle . 6. Structure is stainless, structure is light and beautiful, the flow is easy, operation is easy. 7.dimension: 1500×500×1500mm.

• MOQ 1 Set(s)

We are offering za3137 motorcycle lift 4 strokes teaching model i. Overview technical teaching equipment, vechile trainer, automobile training equipment to university, college, technical schools, training institute. Dimension: 1300×1000×1900(l×w×h) operating environment: temperature-40℃～40℃, humidity≤80% engine type: motorcycle engine engine oil level: api (american petroleum institute) standard sg level, accumulator: maintenance-free battery the whole rack uses international standard square tube , the tube dimension is 40*40*2mm thickness , angle iron is with seamless welding, surface is under high temperature spray treatment after polishing, it is anticorrosive and anti-aging, does not fade, etc., the bottom of the rack is equipped with universal self-locking casters, convenient for the rack movement teaching. Control panel with pure aluminum plate, control panel is painted with color and intuitive electronic control system schematic which is consistent with the original vehicle control system, and with manual and experiment guide books. With engine: four-stroke motorcycle engine 100-125cc instrument: secret key type ignition switch, subsystems: air cooling system, with 1l tank capacity fuel system, electrical system: headlights, rear lights, continuous lights & signal lights ignition: cdi system has a complete color circuit schematic panel, external detection terminals, intelligent fault setting box assembly, removable stand, manual and experiment guide book. The bench enables students to understand the basic structure and working principle of the motorcycle engine, and understand each sensor and actuator position and working principle through the object. Set common faults of the engine through the computer terminals on the panel, through the fault display, students do fault analyzing, detection and diagnosis training, which can cultivate students’ fault analysis, detection and diagnosis thinking ability.

• MOQ 2 Set(s)

We are offering zp6110 uv exposure machine i. Introduction 1.3kw iodine gallium uv light tube 2.it is easy for fixing pcb plate 3. Work zone: 1000mmx1000mm 4. Digital timer 5. Counter range:0-999 second auto reset 6. It can exposure again, separate select up or down exposure. 7.with vacuum sucker function.

• MOQ 1 Set(s)

We are offering zf-mts1102 flexible manufacture system 11 stations i. Overview fms is managed by computer, it is a high efficiency equipment to demo process middle and small components, it has the features such as: multi standard manufacture unit, auto upload material mini cnc machines, whole set of material transmission system, plc system, sensor technology, test technology etc. ii involved course the whole system can be used for mechatronics course, it include pneumatic training, electro pneumatic training, system structure design and analysis, plc program, profibus control experiment, electro servo mechanical arm simulation, cnc process flow, servo ware house, fault remove etc. We can make customer order according to your requirements.

• MOQ 2 Set(s)

We are offering zm2107 central air conditioner trainer i. Overview 1. Function demonstration: it can demonstration structure and work principle of central air conditioner. The central air conditioner can be divided into four parts according to its functions to make students grasp and know it more easily. 2. Training function: the training function is rich and strong. Students can know work principle of central air conditioner through practice training operation. 3. Trouble setup function: there are 26 trouble points in the system and circuits. The students can check and find out troubles from control circuit and system. So it can improve students� practical operation ability and problem analysis talents greatly. 4. Testing function: the trouble can be set up in advance, students can use multi meter and trouble to find out and judge troubles. Ii. Equipment configuration 1.the central air conditioner is consist of host system, water circulation system, central control system, guestroom system, and lobby system. 2.the hose system is consist of a set of refrigeration engine group and a set of heating five sets of water pump driver, a set of catchment facility, various valves, pressure meter and exhaust valve.

• MOQ 1 Set(s)

We are offering zm2110 transparent elevator teaching aids i. Elevator basic structure 1. elevator machine room: include traction machine, brake, speed limiter, traction sheave guard, guide pulley or secondary sheave, hand winding device wheel, control console, power switch, well lighting switch 2. well part: lift car, lift car guide rails, counter-weight guide rail, counter-weight shelf, buffer, limit switch, controlling cable, speed limiter, wire rope tension loading. 3. lift car part: lift car, safety tongs, guide shoe, gate power operator, levelling device, elevator operation panel, lift car inside command button, indicator, lift car lighting system, lift car maintenance box, lift car door. 4. elevator landing door component: landing door, call button box, floor displayer, door mechanical locker, elevator electric interlock. Ii. Elevator basic function 1, input voltage: ac 380, 50hz 2, control mode: programmable controller (plc) regulating speed fm set selected control. 3, programmable controller (plc) :mitsubishi(you can select siemens, or omron) input voltage: ac 220v, 50hz 4, frequency conversion governor: input voltage: ac 220, 60hz current rating: 2.5 a power 1.2 kw 5, traction machine: 6, drive motor voltage: ac 220v, 50hz power: 180w speed: 2800 rmin iii. Electrical control part basic function automatic leveling, elevator automatic open close the door, manual open door in advance, overweight stop running, up and down limit position, open and close door abnormal, layer door chain safeguard, system halted operation（directly drive）, automanual, maintenance control, lighting, fan simulator. Training project: more than 30 simulation fault for elevator.

• MOQ 2 Set(s)

ZM2111 Transparent Elevator Educational Aids I. Elevator basic structure 1. Elevator machine room: include traction machine, brake, speed limiter, traction sheave guard, guide pulley or secondary sheave, hand winding device wheel, control console, power switch, well lighting switch 2. Well part: lift car, lift car guide rails, counter-weight guide rail, counter-weight shelf, buffer, limit switch, controlling cable, speed limiter, wire rope tension loading. 3. lift car part: lift car, safety tongs, guide shoe, gate power operator, levelling device, elevator operation panel, lift car inside command button, indicator, lift car lighting system, lift car maintenance box, lift car door. 4. Elevator landing door component: landing door, call button box, floor displayer, door mechanical locker, elevator electric interlock. II. Elevator basic function 1, Input voltage: AC 380, 50Hz 2, Control mode: programmable controller (PLC) regulating speed FM set selected control. 3, Programmable controller (PLC) :Input voltage: AC 220V, 50Hz 4, Traction machine: 5, Drive motor Voltage: AC 220V, 50Hz Power: 180W Speed: 2800 rmin III. Electrical control part basic function automatic leveling, elevator automatic open close the door, manual open door in advance, overweight stop running, up and down limit position, open and close door abnormal, layer door chain safeguard, system halted operation（directly drive）, automanual, maintenance control, lighting, fan simulator. Training project: more than 30 simulation fault for elevator.

• MOQ 2 Set(s)

We are offering zm3102 elevator teaching model. I. Overview this equipment is mechatronics trainer, it is plc execute model, it can controlled by plc, this teaching model practice students hand on ability, program ability. Ii. Technical parameter 1. Power supply: single phase, three wires, ac 220v, 50hz 2. Environment temperature:0-40℃ 3.environment humidity:

• MOQ 2 Set(s)

We are offering zm3103 double water tank plc execute object i. Overview double water tank trainer is mechatronics trainer, it is plc execute model, it can controlled by plc, this teaching model practice students hand on ability, program ability. Students can learn water pressure, water motor, water flow rate, water temperature knowledge in this trainer, we can supply siemens or mitsubishi plc as you like. It is with rs485 communication port, usb port. Ii. Technical parameter 1. Power supply: single phase, three wires, ac 220v, 50hz 2. Environment temperature:0-40℃ 3.environment humidity:

• MOQ 2 Set(s)

We are offering zm3104 sorting trainer. I. Overview sorting trainer can controlled by plc, this teaching model practice students hand on ability, program ability. This trainer is with different sensors, such as capacitive sensor, inductive sensor, optical fiber sensor, micro switch, to identify the height and color of components, it is controlled by plc. Students can learn industrial sorting, plc knowledge in this trainer, students can edit their own program, to control sorting by their willing. We can supply siemens or mitsubishi plc as you like. It is with rs485 communication port, usb port. Ii. Technical parameter 1. Power supply: single phase, three wires, ac 220v, 50hz 2. Environment temperature:0-40℃ 3.environment humidity:

• MOQ 2 Set(s)

We are offering zm3105 water tank trainer. I. Overview water tank trainer can controlled by plc, this teaching model practice students hand on ability, program ability. This trainer is with different sensors, pumps, water tubes, plc, students can learn how to use plc to control water tank through this trainer, students can learn the relationship of water pressure, water temperature, pump rotary speed, water flow rate through this trainer. We can supply siemens or mitsubishi plc as you like. It is with rs485 communication port, usb port. Ii. Technical parameter 1. Power supply: single phase, three wires, ac 220v, 50hz 2. Environment temperature:0-40℃ 3.environment humidity:

• MOQ 1 Set(s)

We are offering zp6101 surface mount backflow soldering machine. I. Function surface mount backflow soldering machine ii. Technical parameter 1. In welding process, pcb is in static state the surface components should be in correct position, and avoid not be soldering. 2. Soldering zone use far infrared ray heat, and high temperature motor force to be heated. 3. Equip with nitrogen protection connector, and use nitrogen to make protection. 4. Soldering zone use fuzzy control technology, you can only set 3 units of technical parameter, then you can control the whole temperature curve, and you can follow temperature change, blue backlight lcd display. 5. It use 320×240mm dot matrix high resolution lcd display, the dimension of lcd is 113mm dot matrix high resolution lcd80mm. 6. The solding machine can be connected to pc, and use backflow curve to record save software. 7. The welding machine has 4 ways temperature sensor interface, sensor head is pt100, it can correct welding temperature curve through backflow analysis 8. Dimension: 600×450×500mm 9. Peak power: 3.5kw

• MOQ 2 Set(s)

We are offering zp6102 multi-function environmental protection fast plate making system. I. Machine functions 1. Vacuum dual exposure 2. Imaging function 3. Circuit board corrosion function 4. Circuit board via hole function ii. Feature 1.it uses environment protection transparent material, students can see the whole process for go through holes. 2.drawer type exposure function, it has vacuum sucker function, time control function, image function is made of transparent material. Iii. Technical parameter 1.circuit board plate making precision: 4-6mil, 0.1-0.15mm 2.max image function dimension: 300×200mm(transparent corrosion slot 1 set ) 3. Max corrosion dimension: 300×200mm(transparent corrosion slot 2 sets ) 4. Max holes dimension: 300×200mm(transparent corrosion slot 2 set ) 5. Temperature controller: 45-65, and it is adjustable 6. Minimum through hole precision:φ0.3mm 7. Pump work pressure: 1.2kw 8. Work power: 220v, 50hz 9. Dimension: 1700×1200×400mm

• MOQ 2 Set(s)

Zp6103 precision guillotine shear machine i. Overview 1. The use of products: according to the specifications apply copperplate, pvc materials out 2. The biggest cut thickness: 0.4- 4.0 mm; maximum shear wide: 350 mm 3. Appearance volume: 500 * 400 * 500 mm 4. Machine net weight: 30 kg 5. Use special pressure transmission device, the operation is labor-saving, fast 6. With an auxiliary linking piece fixture, convenient operation positioning 7. Imported tungsten carbide cutting tool material, a long life 8. Has a transparent safe protection devices. Use more security configuration: 1 cpu

• MOQ 2 Set(s)

Zp6104 drilling carving machine i. Function 1. Realize automatic matching chemical plate making drilling 2. Realize the physical sculpture ones. Can carve double panel ii. Structure 1. Mechanical transmission mechanism of x, y, z is using linear guide rail, the slider preloaded device, ensure the slider no clearance 2. Whole machine structure and the aluminum parts, whole milling flat, smooth surface, guide rail support stability 3. Xyz the axis is using german imported ball screw, smooth movement, carving high precision, small vibration whole machine tools 4. Spindle motor: 300 w water-cooled frequency conversion motor, 0-60000 rmin, stable life is long, ensure the communication work more than 10 hours motor don't burn. 5. Pcb installation: special fixture card installed, easy to use, can also drilling 5 blocks, rather than through the double-sided adhesive stick. Iii. Technical parameter 1. Control method: high speed digital signal processor (dsp) 2.can pass a computer control more than two sets carving machine 3. Usb interface way 4. Pcb file storage ways pcb gerber

• MOQ 2 Set(s)

We are offering zp6105 high speed directional control pulse punching metallized equipment i. Structure 1. Using special high-speed reversing pulse electroplating power, provide uniform quality coating quality. 2, full abs engineering plastic airframe and internal channel, corrosion seismic resistance to high temperature, beautiful and easy process. 3. Environmental protection black hole process application, no pollution can be directly emissions. 4 cathode swinging technology, prevent the concentration gradient, increase the inner hole solution liquidity. Ii. Technical parameter 1. Four slot structure, has pickling, soaking conductive adhesive, activation, electroplating function. 2. Use transparent clamshell function, it is convenient for observation and save. 3. Maximum board area: 400 x 400 mm. 4. Smallest aperture: 0.3 mm 5. Maximum thickness-diameter ratio, 5:1 6. Output frequency: 0-2 khz adjustable (can transform for dc power) 7, output current: positive 0-5 a, reverse 0-20 a adjustable 8 pulse width: the pulse reversing the power supply, positive 0-100%, reverse pulse width 0-100% alone can be adjusted 9. Constant pressure constant current: current or constant voltage automatic adjustment function, to the current real-time measurement shows two 10 time setting: work time a predetermined function, the remaining time show and then to be automatic power alarm prompt 11. Screen shows: 6 inches big screen color lcd all working parameters.

• MOQ 2 Set(s)

We are offering hand drilling machine. I. Introduction product use: complete the circuit board via, components, board a hole drilling the properties of product: with the soft switch, push rod can automatically start power supply, convenient operation, good stability and big head used together with drilling, drilling high quality, easy to operate. Driving way: dc motor drive directly drill chuck speed: 10000 rmin working voltage: 220 vfrequency 50 hz work power: 100 w basic specifications and data: drilling ability: 0.5-10 mm mesa size: 170 * 170 mm the effective size: 140 mm ontology height: 380 mm the length, width, high: 325 * 250 * 215 mm (packing size)

• MOQ 1 Set(s)

we are offering ZA3132 Rotary Diesel Injection Pump Teaching Model I. Overview Technical teaching equipment, vechile trainer, automobile training equipment to university, college, technical schools, training institute. a.Package:wooden pallet b.Weight:36 kgs c.Dimension: 0.35CBM d. Work environment: 0-40℃ Using in-line diesel pump as material object to carry on dissection on external, which let you see the internal construction clearly, it is turned manually.

• MOQ 2 Set(s)

We are offering zp6114 spray etching machine. I. Introduction spray etching machine mini laboratory use machine. It is for copper plate or print laboratory quickly develop sample and manufacture. Inner with anti-etching pump, make etching liquid double sides spray to sample two sides, etching pcb sensitive layer. Inner immersion program heater, heating developing liquid to develop temperature. With clock preset develop time. ★1. Take imported spray sprinkler 8 units. Spray is uniform. ★2.spray pressure: antiseptic high-pressure magnetic pump, with filter set. ★3.wire diameter:0.1mm， 4. Transparent flip function, it is easy to observe. 5.max sample dimenstion:400×350mm 6.sample develop time:0.1-5 minutes adjustable. ★7.heat temperature is adjustable, heater power: 500w, 220v, 50hz, single phase. 8.with timer function, timer can be preset time as hour, minute, second. 9. Inner dimension:450×400×350mm 10.dimension:600×430×500mm 11.net weight:15kg 12. With equipment desk 1 unit. Dimension:600×500×500mm, use anti corrosion pvc material, the below is cabinet structure, it can put tools, spare parts etc.

• MOQ 2 Set(s)

We are offering za3131 differential gear teaching model i. Overview technical teaching equipment, vechile trainer, automobile training equipment to university, college, technical schools, training institute. A.weight:35 kgs b.dimension: 0.5cbm c. Work environment: 0-40℃ d.package:wooden pallet this product uses original differential mechanism, it is dealt with cut away structure and the cut away section is sketched. The bottom can be welded with rolled steel, or made into a rack with stainless steel (according to the requirement of customers). Students can understand the internal construction and working principle of differential mechanism faster with the product, it is equipped with a matched product manual and a technical instructor.

• MOQ 2 Set(s)

We are offering zp6115 spray cover sheet removers i. Introduction cover sheet removers mini laboratory use machine. It is for copper plate or print laboratory quickly develop sample and manufacture. Inner with anti-etching pump, make etching liquid double sides spray to sample two sides, etching pcb sensitive layer. Inner immersion program heater, heating developing liquid to develop temperature. With clock preset develop time. ★1. Take imported spray sprinkler 8 units. Spray is uniform. ★2.spray pressure: antiseptic high-pressure magnetic pump, with filter set. ★3.wire diameter:0.1mm， 4. Transparent flip function, it is easy to observe. 5.max sample dimenstion:400×350mm 6.sample develop time:0.1-5 minutes adjustable. ★7.heat temperature is adjustable, heater power: 500w，220v，50hz, single phase. 8.with timer function, timer can be preset time as hour, minute, second. 9. Inner dimension:450×400×350mm 10.dimension:600×430×500mm 11.net weight:15kg 12. With equipment desk 1 unit. Dimension:600×500×500mm, use anti corrosion pvc material, the below is cabinet structure, it can put tools, spare parts etc.

• MOQ 2 Set(s)

We are offering zp6113 chemical paint developing machine i. Introduction this develop machine is mini laboratory use machine. It is for copper plate or print laboratory quickly develop sample and manufacture. Inner with anti-etching pump, make etching liquid double sides spray to sample two sides, etching pcb sensitive layer. Inner immersion program heater, heating developing liquid to develop temperature. With clock preset develop time. ★1. Take imported spray sprinkler 8 units. Spray is uniform. ★2.spray pressure: antiseptic high-pressure magnetic pump, with filter set. ★3.wire diameter:0.1mm， 4. Transparent flip function, it is easy to observe. 5.max sample dimenstion:400×350mm 6.sample develop time:0.1-5 minutes adjustable. ★7.heat temperature is adjustable, heater power: 500w，220v，50hz, single phase. 8.with timer function, timer can be preset time as hour, minute, second. 9. Inner dimension:450×400×350mm 10.dimension:600×430×500mm 11.net weight:15kg 12. With equipment desk 1 unit. Dimension:600×500×500mm, use anti corrosion pvc material, the below is cabinet structure, it can put tools, spare parts etc.

• MOQ 1 Set(s)

We are offering za3159 hydraulic power steering movement trainer i. Overview technical teaching equipment, vechile trainer, automobile training equipment to university, college, technical schools, training institute. Overall bench adapt international standard square tube , angle iron seamless welding, after the surface polishing grinding, then the surface is dealt with high temperature spraying plastics , it can anti-corrosion and anti-aging , hardly lose it’s color, at the bottom of the bench is equipped with universal self-locking castor for mobile teaching . Detection board adapt the pure aluminum-plastic panel, on the control panel with perceptual intuition hydraulic steering system schematic diagram, and the color is consistent with the original car control system , and it is equipped with operation specification and experiment guidbook . Adapt the santana 2000 front overhang system and steering system assembly , main configuration is auto tyre , power steer , steering wheel assembly, drum brake, shock absorber , wheel bearing shell assembly , brake disc, etc. Product function : 1.three-phase motor simulation engine power. 2.the layout is according to the auto actual structure and the requirement of assembly installation position . 3.it can carry on dismounting experiment , compare power steering with non power steering , maintenance . 4.it’s equipped with oil pressure gauge , display the steering pressure . 5.it can compare power steering with non power steering , mobile universal wheel bench for moving conveniently .

• MOQ 2 Set(s)

We are offering Chemical Tin Plating Machine. ZP6111 Chemical Tin Plating Machine I. Introduction 1. Usage: electro tinning for double sides circuit board. 2. Tin plating time:8 to 12 minutes 3. Max electro tinning circuit board zone: 450*400mm2 4. Chemical groove max capacity:400×300×500mm3 5. Rectify power work voltage range:0-20V, work current range: 0~30A, work power: 360W Capacity:40 liters

• MOQ 2 Set(s)

We are offering zp6108 high speed directional pulse hole metallizing i. Introduction structure ★1.use high speed pulse power source for plating, supply uniform good quality coating. ★2.fully abs engineer plastic machine body and inner groove, with antiseptic, thermo stability, technology flow is beautiful. ★3.environment protection black hole technology flow application, no pollution, it can direct discharge. ★4. Cathode oscillation technology, prevent , concentration gradient, add hole inner liquid flowability. Technical specification: ★1.with 4 groove structure, with acid-washing, soak conducting resin, activate, electroplating function. ★2.use transparent flip function, it is easy to observe and storage. ★3. Maximum board: 400×400mm, it can electroplating 5 boards at the same time. ★4. Minimum hole diameter: 0.3mm ★5.maximum thickness ratio 5:1 ★6.output frequency: 0-2khz adjustable(it can change as dc power) ★7.output current: forward direction 0-5a, reverse 0-20a adjustable. ★8.pulse width: use pulse directional power, forward direction 0-100%, reverse pulse 0 to 100% single adjustable. 9.constantvoltage constant current: current or voltage is constant, with self adjust function, 2 directional current real time display function. ★10.time setting: work time preset function, time remaining display and automatic power off alarm. ★11.lcd:6 inch full color lcd, display all work specification. 12.circuit protection: with short circuit, open circuit function, supply alarm signal.

• MOQ 1 Set(s)

We are offering zp6112 silk mesh printer i. Introduction this equipment is suitable for small production of pcb product line manual printer. It use wire meshmetal leakage board as print moldboard. Put soldering material or other liquid or solid print to electric board soldering plate accurately. valid print zone: 700mm×600mm adjust precision: 0.05mm print mode: manual frame x direction max adjust distance:20mm workbench y direction max adjust distance:80mm frame q direction adjust range: ±8 frame and workbench adjustable distance: 0 to 10mm dimension: 800mm×1000mm×900mm

• MOQ 1 Set(s)

ZA3133 Wiper System Teaching Model I. Overview Technical teaching equipment, vechile trainer, automobile training equipment to university, college, technical schools, training institute. It uses original auto wiper system as material object, and it is installed on the bottom of the stainless steel frame, and it is fitted with 220V switching power supply which turns 12V AC current directly, it is fitted with wiper switch. When you operate the wiper switch, the wiper system can run normally at three different gears of high speed, low speed and clearance gear.

• MOQ 2 Set(s)

We are offering za3127 starter motor. i. Overview technical teaching equipment, vechile trainer, automobile training equipment to university, college, technical schools, training institute. Dimension: 300*120*200mm i.constitute starter, support, operating manual ii.function 1. It is suitable for professional teaching and actual operating of cars of all levels. 2. Complete exhibition and dynamic demonstration of external and internal components of starter. Ii.craft it used high-strength rigidity material to weld, and its surface is dealt with paint spraying. Iv.training project a.knowing the construction and working principle of starter. B.knowing the construction and working principle of components of starter. Supply english user manual.

• MOQ 2 Set(s)

We are offering zp6117 tin lead plating machine i. Introduction 1.double sides, multi layer circuit board etc. Non-metal material double side drilling hole protection. 2.full abs engineer plastic machine and inner groove, antiseptic, anti high temperature, anti vibration, technology flow is good, outlook is beautiful. 3.★cathode oscillation technology, prevent concentration gradient, add hole liquid flow. Swing time:3-5 timesminute. Technical specification: 4.★max panel:400×400mm, it can electroplate for 5 boards at the same time. 5.minimum hole:0.6mm 6.max thickness diameter ratio, 3:1 7.output voltage:0-15v, adjustable continuously 8.output current:0-20a, adjustable continuously 9.dimension:420×430×420mm 10 ★with 2 groove, one is for tin-lead plating, the other is for quit tin-lead.

• MOQ 2 Set(s)

We are offering zm3101 air conditioner and refrigerator trainer. I. Overview this device is training equipment designed for profession related to refrigeration in vocational colleges, according to the characteristics of air conditioning and refrigerator repair techniques in refrigeration industry, it is designed for air conditioner and refrigerator electrical control and refrigeration system installation and maintenance, which enhances students’ comprehensive vocational abilities for the installation of air conditioners and refrigerators system piping, electrical wiring, commissioning, fault diagnosis and maintenance etc. Device combines fluid mechanics, thermodynamics, heat transfer theory and electrical control and other technologies, and it is suitable for professional teaching and training related to refrigeration. The device consists of air-conditioning system module, refrigerator system module, power supply and instrument module, air conditioning electrical control module, refrigerator electronic thermostat electrical control module, refrigerator intelligent temperature control electrical control modules and other components. Do project training through this device, it can test students’ teamwork ability, planning and organizing ability, refrigeration systems installation and adjustment ability, electrical control circuit maintenance ability, communication skills, professionalism and safety awareness and others. The device uses a modular design, is composed of rail type aluminum alloy installation platform, air conditioning system, refrigerator system, electrical control systems and other components.

• MOQ 1 Set(s)

We are offering zp6118 laser plotter system. I. Introduction laser plotter system consist of laser plotter, raster image processing card, light painting output control software. It can process customer designed photo, image, letter, data. It can process one side, two sides, it can express gerber file, can output pcb file, software function is strong, it is easy to use. Image zie:400mm×300mm(12inchx16inch) scan density: 40008000dpi scan mode: external drum 8 roads parallel scan repeat accuracy:±10μm scan speed: 6minutes12minutes18minutes operate mode: single sheet manual, semi-automatic selectable dimension: 850 mmx480mmx1100mm interface: all signals connect to pc is ttl level adapt range: ad, printing, silk print, pcb

• MOQ 2 Set(s)

We are offering zp6109 automatically circuit board polishing machine. I. Introduction 1.usage: copper-clad plate, aluminum plate, stainless plate, pvc material metal, non metal surface polished treatment, it is usually used in making double sides hole, copper plating and galvanize, ink printing pretreatment etc. 2.function: brush up and water spray, rubber covered roller water uptake, with delivery function. 3. Destination board width: 60cm, destination board thickness: 0.5mm~6mm. 4. Driving motor:0.4kw, driving speed:0.2m~6mmin, continuously viable, drying fan: low noise fan:0.75kw×2set, heating power: 8 ea 0.5kw heating tube.

• MOQ 1 Set(s)

We are offering zf-mts902 modular product system i. Overview modular product system include distribution station, testing station, processing station, handling station, buffering station, robot station(6 dof robot), pressure station, asrs station, sorting station. Each station is installed in aluminum grooves, it is easy for each station to combine to an automotive product line. The modules in each station use modular structure, it is easy for constructing, disassemble, and maintain. Ii. Technical parameter 1, control cabinet main circuit power supply: single phase ac220v ± 10% 50hz 2. Control cabinet control loop power supply: dc24v 3. Temperature: -10 ℃ ~ 40 ℃, 4. Environmental humidity: ≤ 90% (25 ℃) 5. Air supply pressure: 0.5 ~ 0.6mpa 6. Machine capacity: ≤ 1kva 7. Dimensions: 750mm×750mm×1000mm

• MOQ 2 Set(s)

We are offering za3123 4 strokes gasoline engine model training stand i. Overview technical teaching equipment, vechile trainer, automobile training equipment to university, college, technical schools, training institute. Dimension: 650×650×1150（l×w×h） operating environment: temperature -5℃～40℃, humidity≤80% engine type: vw engine model: original santana engine displacement: 1.8l working voltage: 220v equipped with leakage protection switch frequency: 5060hz power: 200w the complete rack use square tube and angle iron of international standardized profile to conduct seamless welding, its surface is dealt with high temperature spraying plastics after polishing, which is anti-corrosion, anti-aging and fastness, it is installed with universal self-locking castor on the bottom of the rack, which is convenience to teach movably. It uses loading motor to be power source which drive the motor run smoothly. Teaching function: we can use the device to understand the consist of electronic control gasoline engine mechanical system, the appearance of each component and the connected relation between each component, which can deepen students, understanding of the composition and working principle of the engine mechanical system and help students understand the abstract control theory. Main training project: knowing the construction and working principle of crank-link mechanism of electronic control gasoline engine. Knowing the construction and working principle of valve mechanism. Knowing the construction and working principle of ignition system. Knowing the construction and working principle of fuel oil supply system. Knowing the construction and working principle of cooling system. Knowing the construction and working principle of lubrication system.

• MOQ 1 Set(s)

We are offering za3155 vehicle air conditioner training stand. I. Overview technical teaching equipment, vechile trainer, automobile training equipment to university, college, technical schools, training institute. Dimension: 1300×1000×1900(l×w×h) operating environment:temperature-40℃～40℃, humidity≤80% net weight: 150kg air conditioning type: 134a motor power: 2.2kw ac contactor: chint car type: "superman of the times" of santana the whole rack uses international standard square tube with 40*40*2mm thickness , angle iron is with seamless welding, surface is under high temperature spray treatment after polishing, it is anticorrosive and anti-aging, does not fade, etc., the bottom of the rack is equipped with universal self-locking casters, convenient for the rack movement teaching. Control panel with pure aluminum plate, control panel is painted with color and intuitive air conditioning system schematic which is consistent with the original vehicle control system, and with manual and experiment guide books. The bench uses santana manual air conditioning system as the base. Components: air conditioning control panel, blowers, power tube, air conditioning evaporator assembly, air conditioning compressor, condenser fan, three-phase motor, dryer, refrigeration piping, removable stand, instruction manual. Function: it is suitable to do practical operating skills training and examining for automobile professional students.