Specially designed and moulded Membranes in these Junction Boxes, act as a Cable Glands offering IP 65 protection. After piercing the membrane with a sharp instrument, the cable flexible conduit has to be inserted and slightly pulled out (withdrawn) to achieve a tight wrap around the cable conduit resulting in positive clamping. Junction Boxes are also available with specially designed Nipples which act as Cable Glands offering IP 65 protection.
These Conduit Glands made of 4 piece fitting are designed to suit all types of liquid tight coduits. The use of nickel-plated brass guarantees high corrosion resistance. In order to maintain a common usage standard for the fittings, small adjustments on the correction sets are necessary.
Ventilation Plugs are used for equalizing the pressure inside and outside the enclosure. The same is achieved with the help of a membrane inside the ventilation plug, which allows for gases (air) to pass through it while blocking liquids and particulate solids (dust). Applications Benefits : 1) These prevent components inside the enclosure from being exposed to pressurized gases when the enclosure heats up. (By virtue of pressure equalization)
These hoods are suitable for conductors which run perpendicular to the surface on which the appropriate hood and housing are mounted. The spring loaded single locking system ensures a perfect mating between the male and the female inserts while providing them with IP 66 protection.
EXPLOSION PROOF TRIPLE SEAL STANDARD BRASS / S.S CABLE GLANDS - OCTANS
These Glands are produced in accordance to EN 60079-0:2009EN 60079-1:2007 EN 60079-7:2007EN 60079-11:2010EN 60079-31:2009. Because of triple seal they have wide clamping range they are used in mobile offshore, marine application, chemical & petro chemical industry.
For using liquid tight conduit glands with SLI & SLB metallic conduits it is recommended to replace the standard polyamide clmaping ring inside these glands with metal clamping rings. These clamping rings also increase the pull out strength of the conduit.
These inserts are available from 4 to 48 poles. These are polarized to prevent incorrect coupling between the male and the female inserts. The screw terminals are provided with wire protectors to prevent damage to the conductors.
These stainless steel glands are liquid tight, offer excellent strain relief and have lameller designed plastic inserts for protection against distortion. These glands are suitable for use in tunnel lighting and chemical industry where high mechanical and chemical resistance is required.
Specially designed and moulded Membranes in these Junction Boxes, act as a Cable Glands offering IP 65 protection. After piercing the membrane with a sharp instrument, the cable flexible conduit has to be inserted and slightly pulled out (withdrawn) to achieve a tight wrap around the cable conduit resulting in positive clamping. Junction Boxes are also available with specially designed Nipples which act as Cable Glands offering IP 65 protection.
These Glands are produced in accordance to EN 60079-0:2009EN 60079-1:2007 EN 60079-7:2007EN 60079-11:2010EN 60079-31:2009. Because of triple seal they have wide clamping range they are used in mobile offshore, marine application, chemical & petro chemical industry.
In case housings with hinged covers are not procured initially, the covers can be separately purchased and retro fitted onto the housings. These covers help maintain the IP protection grade by closing onto the housings when the hoods are disconnected from the housings.
These manifolds are used to join two or three flexible Conduits of the same size or of different sizes with outside gripping. They are available in Straight, Elbow, 'T' and 'Y' shapes.
DIN Rail supports are used for housing of high connection density contact carriers or inserts within control cabinets panels. No tools are needed for installing these products. The inserts contact carriers can be snapped into the DIN Rail supports with hands. Also the DIN Rail supports can be snapped on to the DIN Rails without tools. These DIN Rail supports are fully cross compatible with inserts of other makes. The inserts and hence the contacts are fully secured by locking the male inserts with the female inserts. This is achieved by using locking levers.
These male and female crimp contacts are available in 10 Amp and 16 Amp versions. The 10 Amp crimp contacts are suitable for conductor size upto 2.5 sq.mm. and the 16 Amp crimp contact are suitable for conductor size upto 4 sq.mm.
These inserts are available from 4 to 48 poles. These are polarized to prevent incorrect coupling between the male and the female inserts. The screw terminals are provided with wire protectors to prevent damage to the conductors.
These inserts are used in applications where sealing and strain relief protection is required for multiple cables passing through a single cable gland.
Blind Stops made of Brass are used wherever threads previously cut must be closed for preventing dust, dirt and foreign matters from entering the enclosure or equipment.
These inserts are available from 6 to 216 poles. These are polarized to prevent incorrect coupling between the male and the female inserts. The conductors need to be crimped with appropriate male crimp contacts and then made to enter the insert where they are held in place with the help of a flexible locking device.
Industrial Plugs and Sockets from Controlwell provide a versatile and robust connection system for industrial field and factory connection applications. These Plugs and Sockets are designed and manufactured as per IEC 60309-1 and IEC 60309-2 standards. The housing of these Industrial Plugs and Sockets is made of highly durable Polyamide 6 raw material, having a very high impact resistance. This material is halogen free and is Non-Flammable with a flammability rating of V0. Contacts are made from an electroplated copper alloy with high corrosion resistance and very low contact resistance (
Blind Stops made of Polyamide 6 and Brass are used wherever threads previously cut must be closed for preventing dust, dirt and foreign matters from entering the enclosure or equipment.
These Conduit Glands are very easy and quick to install. In combination with galvanized steel or PVC coated galvanized steel conduits they offer IP54 class protection. Manufactured from nickel plated brass they offer excellent resistance to environmental factors.
These metal ferrules are used in the combination with clamping ring to maintain the IP 67 grade of protection for liquid tight PVC coated smooth conduits. They are used as cover of conduit ends to avoid cable damage.
Mounting Clips are used for supporting conduits. These clips are made of High Quality Impact Resistant Polyamide. The mounting clips are stackable and are fixed with the help of screws on to the panel or equipment surface.
These hoods are suitable for housing compact square type male or female inserts. They are available with options of top wire entry, side wire entry and top wire entry with lever.
Bulk head mount housings are mounted over cut-outs in the electrical control panels where the conductors approach the inserts fixed inside the housings through the cut-outs.
Simpleseal are special grommets which are simple to use and require no tools for installation. They differ from conventional grommets as they provide IP 67 protection. They can be installed from one side of the panel without any need for installation of lock nuts from the other side as in conventional cable glands. With these grommets necessity of blind stops is removed as in these grommets the opening is always sealed until the membrane is pushed out by the cable. These are suitable for enclosures with wall thickness from 0.5 to 4.0 mm.
These enclosures are used for creating power distribution circuits. Various options are available based on the number of miniature circuit breakers (MCBs), that can be installed inside in an array. Most of these enclosures have hinged lids for easy access to the MCBs installed inside.
Distributors made of Polyamide can be used instead of a distribution box. These special connectors are used to clamp standard corrugated conduits. They can be configured into the basic shapes of Y (TYC), T (TTC), V(TVC) and straight through (TSC).
In various applications a bank (group) of male or female identical connectors are placed side by side. In such applications it is difficult to couple the connectors in the right sequence. Coding pins are used to prevent such false coupling possibilities. Coding pins are used in place of normal insert fixing screws. In this way coupling of correct connectors is ensured. Single code pins offer coding possibilities for a maximum of 6 identical connectors placed side by side.
These combination boxes are an ideal choice for combining Industrial Plugs & Sockets (CEE Connectors) & miniature circuit breakers. Various multi pin sockets can be mounted on the front of the box. This in conjunction with the circuit breakers provide an easy solution for mobile power outlet boxes typically required on off site locations as well as factory shop floors.
CONSTRUCTION SIDE ENTRY Housing Hood - WITH 4 PEGS
These hoods are suitable for conductors which run parallel to the surface on which the appropriate hood and housing are mounted. The spring loaded double locking system ensures a perfect mating between the male and the female inserts even if accidentally one of the locks opens up.
Ventilation plugs are used for pressure compensation and moisture protection. This is achieved with the help of an integral membrane. It can be used on control panels, motor frames, ensclosures, underground lights, etc.
Surface mount type housings are used where a cable terminates into the male or female insert housed inside it. i.e. It is mounted on a plain surface with a cable coming into the housing via a cable gland mounted on the body of the housing. In this case a single lock mechanism ensures IP 65 class protection to the inserts after mating with the appropriate hood.
Surface mount type housings are used where a cable terminates into the male or female insert housed inside it. i.e. It is mounted on a plain surface with a cable coming into the housing via a cable gland mounted on the body of the housing. In this case the double locking mechanism ensures IP 65 class protection to the inserts even if one of the locks accidentally opens up.
Junction Boxes are made of halogen-free ABS, which has high resistance to chemicals and atmospheric agents. By virtue of the design they offer IP 65 protection with the help of silicon rubber gasket in EPDM. They are available with plain walls, nipples and membrane. Junction-Box are offered with press-on lids, screw lids and hinged lids. Stainless steel screws are also available on request for lid fastening. Choice of grey colour lid or transparent lid is also available on request.
In this case the bulk head mount housings are provided with a hinged cover which closes over the housing in the absence of the hood to be mounted on it.
COMPACT SQUARE TYPE BULK HEAD MOUNT RIGHT ANGLED HOUSINGS
These bulk head mounting type right angled housings are suitable for hoods which are connected parallel to the mounting surface. They can house male or female compact square type inserts.
Protection Tabs made of Polyamide 6 are used in assembly work for instruments, machines etc., where only Cable Glands are mounted and cable connection is made later. This prevents dust and moisture from penetrating the enclosure or equipment.
These stainless steel glands are liquid tight, offer excellent strain relief and have lameller designed plastic inserts for protection against distortion. These glands are suitable for use in tunnel lighting and chemical industry where high mechanical and chemical resistance is required.
These bulk head mounting type straight housings are suitable for hoods which are connected perpendicular to the mounting surface. They can house male or female compact square type inserts.
Rutaseal and Simpleseal are special grommets which are simple to use and require no tools for installation. They differ from conventional grommets as they provide IP 67 protection. They can be installed from one side of the panel without any need for installation of lock nuts from the other side as in conventional cable glands. With these grommets necessity of blind stops is removed as in these grommets the opening is always sealed until the membrane is pushed out by the cable. These are suitable for enclosures with wall thickness from 0.5 to 4.0 mm.
Navi Mumbai, Maharashtra, India
