Mumbai, Maharashtra, India
Our Products
| We are one of the largest Traders and service providers in HR/CR segment in Western India. Product conform to national and international standards.Available in coil/slit/sheet form.We represent big steel manufacturers like JSW Ispat, SAIL, Uttam, etc At any given point of time we have more than 7000mt of HR/CR material in our stock at two locations viz., Mumbai and Pune . we cater to wide spectrum of Customers /Users for their JIT requirements on regular basis. We can cater to our buyers requirements in most of the Thicknesses, Grades, Sizes, Length and Width. We supply in tailor made or customized sizes. We also ship the Plates/Sheets/Blanks duly Oiled and Pickled as per the buyersrequirement in 20containers, We can supply in Small Quantities | |
| Sr. No. | GRADES | THK. (mm) | Width |
| 1 | Hot Rolled – En 10025 S235JR, Fe 410, St 37, St 42, IS2062 A, SH 41, CG/CR, SH29, SH20 Al, SH29 Am, MC2052, MC410, WT41, WG 29, | 3,4,5,6,8,10, 12,16, 20, 25 | 150 mm to 2000 mm |
| 2 | High Tensile – En 10025 S355 , En 10149 S355 MC, ST 52.3, QSTE 380 TM, Fe 510, TR46 | 3 mm to 30 mm | 150 mm to 2000 mm |
| 3 | Cold Rolled – IS 513, St 37, St 12 | 0.30 to 3.00 mm | 150 mm to 1500 mm |
| 4 | Chequered Plates CP41 | 3 to 10mm | 1000 mm to 1500 mm |
| We deal in Mild Steel Ingots/Billets used in manufacture of TMT Bars, Angles, Channels and BeamsWe can supply Mild Steel Ingots/Billets in various sizes and grades | |
| We manufacture MS Angles/Channels/Beams of various sizes | |
| We supply the material duly Straighten | |
| We can supply in required Sizes and Grades required by the buyer | |
| MS Angles are used for Transmission and Tele Communication Towers after HDG and Fabrication | |
| We have modern Laboratory for testing of Raw material and Finished Products |
| We can supply Pellets both in DR grade and BF grades | |
| High quality Indian Pellets acts as a feed stock for sponge Iron Plants | |
| Indian Pellets are low in Sulphur and Phosphorus. |
|
Particulars Chemical (ON DRY BASIS) |
Grade % | Tolerance | |
| Fe | 65 | Minimum | |
| FeO | 0.3 | Maximum | |
| SiO2 + Al2O3 | 0.5 | Maximum | |
| CaO | 0.03 | ± 0.01 | |
| MgO | 0.06 | ± 0.01 | |
| Basicity | 65 | Maximum | |
| Phosphorus | 0.05 | Maximum | |
| Physical Properties | Value | Tolerance | |
| Bulk Density | 2.2 T/m3 | ± 0.2 | |
| Tumbler Index | 93 % | Minimum | |
| Abrasion Index | 3 % | Min ± 0.5 % | |
| Cold Crushing Strength (Avg) | 250 Kg/P | Minimum | |
| Size Analysis | |||
| 8 - 16 mm | 94 % | Minimum | |
| -5 mm | 2 % | Maximum | |
| +16 mm | 4 % | Maximum | |
| Metallurgical Properties | |||
| Porosity | 18 % | Minimum | |
| Reducibility | 62 % | Minimum | |
