Ludhiana, Punjab, India
Our Products
| Part No. | OD Ø D mm |
Bore Ø d mm |
Ø D1 mm |
W mm |
L1 mm |
L2 mm |
| RR TSL 50x6 | 50 | 6 | 58 | - | 5 | 80 |
| RR TSL 50x8 | 50 | 6 | 58 | - | 5 | 80 |
| RR TSL 50x10 | 50 | 10 | 58 | - | 5 | 80 |
| RR TSL 50x12 | 50 | 12 | 58 | - | 5 | 80 |
| RR TSL 50x16 | 50 | 16 | 58 | 12 | 5 | 80 |
| RR TSL 50x20 | 50 | 20 | 58 | 12 | 5 | 80 |
| RR TSL 50x25 | 50 | 25 | 58 | 12 | 5 | 80 |
| RR TSL 50x32 | 50 | 32 | 58 | 12 | 5 | 80 |
| RR TSL 50x40 | 50 | 40 | 58 | 12 | 5 | 80 |
| RR TSL 40x6 | 40 | 6 | 48 | - | 5 | 80 |
| RR TSL 40x8 | 40 | 8 | 48 | - | 5 | 80 |
| RR TSL 40x10 | 40 | 10 | 48 | - | 5 | 80 |
| RR TSL 40x12 | 40 | 12 | 48 | - | 5 | 80 |
| RR TSL 40x16 | 40 | 16 | 48 | 12 | 5 | 80 |
| RR TSL 40x20 | 40 | 20 | 48 | 12 | 5 | 80 |
| RR TSL 40x25 | 40 | 25 | 48 | 12 | 5 | 80 |
| RR TSL 40x32 | 40 | 32 | 48 | 12 | 5 | 80 |
| RR TSL 32x6 | 32 | 6 | 38 | - | 5 | 60 |
| RR TSL 32x8 | 32 | 8 | 38 | - | 5 | 60 |
| RR TSL 32x10 | 32 | 10 | 38 | - | 5 | 60 |
| RR TSL 32x12 | 32 | 12 | 38 | - | 5 | 60 |
| RR TSL 32x16 | 32 | 16 | 38 | 10 | 5 | 60 |
| RR TSL 32x20 | 32 | 20 | 38 | 10 | 5 | 60 |
| RR TSL 32x25 | 32 | 25 | 38 | 10 | 5 | 60 |
| RR TSL 25x8 | 25 | 8 | 33 | - | 5 | 50 |
| RR TSL 25x10 | 25 | 10 | 33 | - | 5 | 50 |
| RR TSL 25x12 | 25 | 12 | 33 | - | 5 | 50 |
| RR TSL 25x16 | 25 | 16 | 33 | 10 | 5 | 50 |
| RR TSL 20x8 | 20 | 8 | 28 | - | 5 | 50 |
| RR TSL 20x10 | 20 | 10 | 28 | - | 5 | 50 |
| RR TSL 20x12 | 20 | 12 | 28 | - | 5 | 50 |
| RR TSL 16x8 | 16 | 8 | 24 | - | 5 | 40 |
| RR TSL 16x10 | 16 | 10 | 24 | - | 5 | 40 |
| Part No. | Suitable For Taper | Angle Ø |
M | Ø d mm |
Ø d1 mm |
Ø d2 mm |
Ø d3 mm |
Ø d4 mm |
L1 mm |
L2 mm |
L mm |
S mm |
Fig. |
| RR PS BT40 45 ° | BT-40 | 45 ° | M16 | 17 | 23 | 10 | 15 | - | 35 | 28 | 60 | 19 | 1 |
| RR PS BT40 45 ° CH | BT-40 | 45 ° | M16 | 17 | 23 | 10 | 15 | 4 | 35 | 28 | 60 | 19 | 2 |
| RR PS BT40 60 ° | BT-40 | 60 ° | M16 | 17 | 23 | 10 | 15 | - | 35 | 28 | 60 | 19 | 1 |
| RR PS BT40 60 ° CH | BT-40 | 60 ° | M16 | 17 | 23 | 10 | 15 | 4 | 35 | 28 | 60 | 19 | 2 |
| RR PS BT40 90 ° | BT-40 | 90 ° | M16 | 17 | 23 | 10 | 15 | - | 35 | 28 | 60 | 19 | 1 |
| RR PS BT40 90 ° CH | BT-40 | 90 ° | M16 | 17 | 23 | 10 | 15 | 4 | 35 | 28 | 60 | 19 | 2 |
| RR PS BT50 45 ° | BT-50 | 45 ° | M24 | 25 | 38 | 17 | 23 | - | 45 | 35 | 85 | 30 | 1 |
| RR PS BT50 45 ° CH | BT-50 | 45 ° | M24 | 25 | 38 | 17 | 23 | 6 | 45 | 35 | 85 | 30 | 2 |
| RR PS BT50 60 ° | BT-50 | 60 ° | M24 | 25 | 38 | 17 | 23 | - | 45 | 35 | 85 | 30 | 1 |
| RR PS BT50 60 ° CH | BT-50 | 60 ° | M24 | 25 | 38 | 17 | 23 | 6 | 45 | 35 | 85 | 30 | 2 |
| RR PS BT50 90 ° | BT-50 | 90 ° | M24 | 25 | 38 | 17 | 23 | - | 45 | 35 | 85 | 30 | 1 |
| RR PS BT50 90 ° CH | BT-50 | 90 ° | M24 | 25 | 38 | 17 | 23 | 6 | 45 | 35 | 85 | 30 | 2 |
Manufactured from high grade Carbon Steel , these live Centers have a hardened body that imparts extra strength & rigidity. The point is precisely ground to 60 & hardened to with in 60-63HRC . Live Centers are also available with Carbide Tipped Point. Maximum radial run out with in 0.015mm. These centers have thrust ball bearing for axial load and taper roller bearing for centri-fugal load.
| Ordering No | Morse Taper Outside (MT) |
Overall Length (MM) |
Diameter of point (MM) |
Body Diameter (MM) |
| REC /2001 | MT1 | 123 | 18 | 40 |
| REC /2002 | MT2 | 136 | 18 | 40 |
| REC /2003 | MT3 | 178 | 24 | 60 |
| REC /2004 | MT4 | 220 | 28 | 64 |
| REC /2005 | MT5 | 262 | 36 | 75 |
| REC /2006 | MT6 | 369 | 53 | 96 |
Drill Sleeves or Reduction Sleeves are used to adapt smaller morse taper Shank. tools to larger machine Spindles.These are available in two types.
A Grade-Made from high grade Carbon Steel-Completely hardened & precision ground internally & externally.
Workshop Grade-Made from Carbon Steel.Fully ground on the outside & having a reamed finish on the inside.
| Ordering No. Grade A |
Ordering No. Workshop Grade |
Morse Taper Outside (MT) |
Morse Taper Inside (MT) |
Overall length (MM) |
| RDS /21 | RDSW /21 | 2 | 1 | 92 |
| RDS /31 | RDSW /31 | 3 | 1 | 99 |
| RDS /32 | RDSW /32 | 3 | 2 | 112 |
| RDS /41 | RDSW /41 | 4 | 1 | 124 |
| RDS /42 | RDSW /42 | 4 | 2 | 124 |
| RDS /43 | RDSW /43 | 4 | 3 | 140 |
| RDS /51 | RDSW /51 | 5 | 1 | 156 |
| RDS /52 | RDSW /52 | 5 | 2 | 156 |
| RDS /53 | RDSW /53 | 5 | 3 | 156 |
| RDS /54 | RDSW /54 | 5 | 4 | 171 |
| RDS /62 | RDSW /62 | 6 | 2 | 218 |
| RDS /63 | RDSW /63 | 6 | 3 | 218 |
| RDS /64 | RDSW /64 | 6 | 4 | 218 |
| RDS /65 | RDSW /65 | 6 | 5 | 218 |
| Part No. | Shank Taper | ∅ d mm |
∅ D mm |
∅ D1 mm |
L mm |
L1 mm |
Conc. Error mm | Max. RPM |
| PC MT2 25-50 | MT-2 | 25 | 55 | 17.780 | 64.0 | 65.0 | 0.015 | 750 |
| PC MT2 30-65 | MT-2 | 30 | 65 | 17.780 | 64.0 | 66.0 | 0.015 | 750 |
| PC MT2 40-75 | MT-2 | 40 | 77 | 17.780 | 64.0 | 69.0 | 0.015 | 600 |
| PC MT2 25-50 | MT-3 | 25 | 55 | 23.825 | 81.0 | 65.0 | 0.015 | 750 |
| PC MT2 30-65 | MT-3 | 30 | 65 | 23.825 | 81.0 | 66.0 | 0.015 | 750 |
| PC MT3 40-75 | MT-3 | 40 | 77 | 23.825 | 81.0 | 69.0 | 0.015 | 600 |
| PC MT3 50-90 | MT-3 | 50 | 90 | 23.825 | 81.0 | 70.0 | 0.015 | 600 |
| PC MT3 65-100 | MT-3 | 65 | 102 | 23.825 | 81.0 | 70.0 | 0.015 | 500 |
| PC MT3 75-125 | MT-3 | 75 | 127 | 23.825 | 102.5 | 98.5 | 0.015 | 350 |
| PC MT4 25-50 | MT-4 | 25 | 55 | 31.267 | 102.5 | 67.5 | 0.015 | 750 |
| PC MT4 30-65 | MT-4 | 30 | 65 | 31.267 | 102.5 | 68.5 | 0.015 | 750 |
| PC MT4 40-75 | MT-4 | 40 | 77 | 31.267 | 102.5 | 70.5 | 0.015 | 600 |
| PC MT4 50-90 | MT-4 | 50 | 90 | 31.267 | 102.5 | 71.5 | 0.015 | 600 |
| PC MT4 65-100 | MT-4 | 65 | 102 | 31.267 | 102.5 | 71.5 | 0.015 | 500 |
| PC MT4 75-125 | MT-4 | 75 | 127 | 31.267 | 102.5 | 93.0 | 0.015 | 350 |
| PC MT4 75-150 | MT-4 | 75 | 153 | 31.267 | 102.5 | 98.0 | 0.015 | 300 |
| PC MT4 100-175 | MT-4 | 100 | 178 | 31.267 | 102.5 | 128.0 | 0.015 | 250 |
| PC MT4 100-200 | MT-4 | 100 | 204 | 31.267 | 102.5 | 128.0 | 0.015 | 250 |
| PC MT5 25-50 | MT-5 | 25 | 55 | 44.399 | 129.5 | 67.5 | 0.015 | 750 |
| PC MT5 30-65 | MT-5 | 30 | 65 | 44.399 | 129.5 | 68.5 | 0.015 | 750 |
| PC MT5 40-75 | MT-5 | 40 | 77 | 44.399 | 129.5 | 71.5 | 0.015 | 600 |
| PC MT5 50-90 | MT-5 | 50 | 90 | 44.399 | 129.5 | 72.5 | 0.015 | 600 |
| PC MT5 65-100 | MT-5 | 65 | 102 | 44.399 | 129.5 | 72.5 | 0.015 | 500 |
| PC MT5 75-125 | MT-5 | 75 | 127 | 44.399 | 129.5 | 94.5 | 0.015 | 350 |
| PC MT5 75-150 | MT-5 | 75 | 153 | 44.399 | 129.5 | 99.0 | 0.015 | 300 |
| PC MT5 100-175 | MT-5 | 100 | 178 | 44.399 | 129.5 | 128.0 | 0.015 | 250 |
| PC MT5 100-200 | MT-5 | 100 | 204 | 44.399 | 129.5 | 128.0 | 0.015 | 250 |
| PC MT5 100-230 | MT-5 | 100 | 231 | 44.399 | 129.5 | 145.0 | 0.015 | 200 |
| PC MT6 65-100 | MT-6 | 65 | 102 | 63.348 | 182.0 | 85.0 | 0.015 | 500 |
| PC MT6 75-125 | MT-6 | 75 | 127 | 63.348 | 182.0 | 96.0 | 0.015 | 350 |
| PC MT6 75-150 | MT-6 | 75 | 153 | 63.348 | 182.0 | 101.0 | 0.015 | 300 |
| PC MT6 100-175 | MT-6 | 100 | 178 | 63.348 | 182.0 | 123.5 | 0.015 | 250 |
| PC MT6 100-200 | MT-6 | 100 | 204 | 63.348 | 182.0 | 123.5 | 0.015 | 250 |
| PC MT6 100-230 | MT-6 | 100 | 231 | 63.348 | 182.0 | 14.0 | 0.015 | 200 |
Manufactured from selected high grade carbon steel. These shanks can be modified to suit individual requirement for mounting cutters etc available in two types - with tangs and drawbar threaded.
| Ordering No. Tang Arbors | Ordering No Drawbar Threaded Arbors | Shanks Tapers | Dia | Draw Bar Thread |
| RAB/101 | RAB/201 | MT1 | 1" | 1/4 BSW |
| RAB/102 | RAB/202 | MT2 | 1" | 3/8 x 16 |
| RAB/103 | RAB/203 | MT3 | 1" | 3/8 x 16 |
| RAB/104 | RAB/204 | MT1 | 25mm | M6 |
| RAB/105 | RAB/205 | MT2 | 25mm | M10 |
| RAB/106 | RAB/206 | MT3 | 25mm | M10 |
| RAB/107 | RAB/207 | R8 | 1-1/4 | 7/16 UNF |
Manufactured from selected high grade carbon steel hardened & ground all over to increase resistance to nwear. Drawbar threaded
| Ordering No | Morse Taper (MT) | Chucks Taper | Draw Bar Thread |
| RA/501 | 1 | JT1 | 1/4 BSW |
| RA/502 | 1 | JT1 | M6 |
| RA/503 | 2 | JT6 | 3/8 BSW |
| RA/504 | 2 | JT6 | M10 |
| RA/505 | 2 | JT33 | 3/8 BSW |
| RA/506 | 2 | JT33 | M10 |
| RA/507 | 2 | JT3 | 3/8 BSW |
| RA/508 | 2 | JT3 | M10 |
| RA/509 | 2 | B16 | M10 |
| RA/510 | 3 | JT6 | 3/8 BSW |
| RA/511 | 3 | JT6 | M10 |
| RA/512 | 3 | B16 | M10 |
Tap wrenches with an all steel body. Jaws are hardened tempered for increased resistance to wear. The wrench body is black with attractive chrome plated handles. Chromed plated handles with knurled ends provide a comfortable non slip grip.
An Excellent Range of Steel Squares Whilst idea for everyday workshop use, these are also suitable for good working Application. Made from Selected Steel With hardened blades, these Squares have accurate right angles on the inside and outside. Both the blades are accurately ground which ensures Straightness and Parallelism.
| Ordering No. | Inch | mm |
| RTS - 2 | 2 | 50 |
| RTS - 3 | 3 | 75 |
| RTS - 4 | 4 | 100 |
| RTS - 6 | 6 | 150 |
| RTS - 8 | 8 | 200 |
| RTS - 9 | 9 | 225 |
| RTS - 10 | 10 | 250 |
| RTS - 12 | 12 | 300 |
| RTS - 16 | 16 | 400 |
| RTS - 18 | 18 | 450 |
| RTS - 20 | 20 | 500 |
| RTS - 24 | 24 | 600 |
Manufactured from selected high quality steel.Punches are hardened and tempered to give durability & extended life even after repeated use .The striking end is bevelled to prevent breakage & accidents due to flying splinters. The numbers Punch set contains 9Pcs0to9. Number 6&9 are interchangeable. The Letter punch set contains 27 Pcs alphabets A to Z and &. These sets are packed in plastic boxes.
| Ordering No. Number Punch Set (9 Pc.Set) |
Stamp Size Inch |
Stamp Size MM |
| RNP/1 | 1/16 | 1 |
| RNP/2 | 3/32 | 2 |
| RNP/3 | 1/8 | 3 |
| RNP/4 | 5/32 | 4 |
| RNP/5 | 3/16 | 5 |
| RNP/6 | 1/4 | 6 |
| RNP/8 | 5/16 | 8 |
| RNP/10 | 3/8 | 10 |
| RNP/12 | 1/2 | 12 |
Manufactured From Selected Carbon Steel, These are Accurately hardened for increased life.
The working tips are centered and ground to the correct angle (90 included angle) for increased efficiency in marking. The striking end is chamfered to prevent breakage.
Size:- 1/8", 5/32", 3/16", 1/4", 5/16", 3/8"Available in :- 4" & 6" Lengths.Also Available with Squares Heads.
With our vast experience in this domain, we are engaged in offering our clients a wide range of T-Tap Wrench. These Wrenches are manufactured using utmost quality basic material under strict industry laid norms at our equipped production unit. The offered wrenches are tested by a team of quality controllers on various stages in order to make sure that the offered range is flawless in all aspects.
Our customers can avail from us T-Tap Wrench, which are made from high grade quality raw materials. Our T-Tap Wrenches can be customized as per our customers specifications and it can be availed at industrial leading price.
| No. | Capacity (Inches) | Length |
| A | 1/16-3/16 | 4" |
| B | 5/32-1/4 | 4" |
| C | 3/16-5/16 | 4" |
| D | 1/4-1/2 | 4" |
