Dubond's Rainshield is composed of high quality acrylic emulsion polymer, light fast & weather durable pigments, properly selected & graded fine fillers, additives & biocides. It is used as a waterproofing & protective coating for exterior walls of the buildings.
Areas of Application
All types of exterior masonry surfaces, concrete, cement sand renderings, etc.
Method of Application

• Surface Preparation
• Priming
• All new cement-sand renderings /concrete surfaces should be allowed to age 6 to 8 weeks before surface coating.
• Surface for treatment must be thoroughly cleaned of all laitance, loose material, oil, grease, etc. by mechanical means such as wire brushing & shot blasting.
• Finally vacuum cleaning of all loose solids and liquids can be done, if required.
• All surface cracks up to 5 mm width should be filled up with Dubond's Acrylic Crack Filler.
• All types of exterior masonry surfaces, concrete, cement sand renderings, etc.

Application

• Use Dubond's Rainshield directly from the container. Stir contents well before use.
• Apply two neat coats of Dubond's Rainshield without dilution by brush or roller at a time interval of 5-6 hours.
• For enhanced protection, apply additional coat of Dubond's Rainshield on rain lashing walls, chajjas and parapet walls.
• Allow the coated surface to air cure fully for 7 days.

Precautions & Limitations

• Do not dilute Dubond's Rainshield.
• Recommended to be primed with Dubond's Hydro Prime only.
• Do not apply when ambient temperature is below 10 C or above 45 C.
• Do not apply in direct sunlight or during rains.
• Adhesion property may get affected over putty and very smooth surfaces.

Coverage
3.0 to 3.5 m per litre for 2 coats Coverage may vary depending upon the texture and porosity of the surface.
Shelf Life & Storage
Shelf life is 24 months from the date of manufacturing in unopened conditions. Store in a cool and dry place. Keep away from direct sunlight
Health & Safety Precautions

• Skin contact : Wash skin with soap & water. Remove contaminated clothes.
• On eye contact : Immediately splash eyes with plenty of water. Consult Physician if irritation persists.
• Ingestion : Do not induce vomiting. Never give anything by mouth to an unconscious person. Call a Physician

Dubond's Rainshield is composed of high quality acrylic emulsion polymer, light fast & weather durable pigments, properly selected & graded fine fillers, additives & biocides. It is used as a waterproofing & protective coating for exterior walls of the buildings.
Areas of Application
All types of exterior masonry surfaces, concrete, cement sand renderings, etc.
Method of Application

• Surface Preparation
• Priming
• All new cement-sand renderings /concrete surfaces should be allowed to age 6 to 8 weeks before surface coating.
• Surface for treatment must be thoroughly cleaned of all laitance, loose material, oil, grease, etc. by mechanical means such as wire brushing & shot blasting.
• Finally vacuum cleaning of all loose solids and liquids can be done, if required.
• All surface cracks up to 5 mm width should be filled up with Dubond's Acrylic Crack Filler.
• All types of exterior masonry surfaces, concrete, cement sand renderings, etc.

Application

• Use Dubond's Rainshield directly from the container. Stir contents well before use.
• Apply two neat coats of Dubond's Rainshield without dilution by brush or roller at a time interval of 5-6 hours.
• For enhanced protection, apply additional coat of Dubond's Rainshield on rain lashing walls, chajjas and parapet walls.
• Allow the coated surface to air cure fully for 7 days.

Precautions & Limitations

• Do not dilute Dubond's Rainshield.
• Recommended to be primed with Dubond's Hydro Prime only.
• Do not apply when ambient temperature is below 10 C or above 45 C.
• Do not apply in direct sunlight or during rains.
• Adhesion property may get affected over putty and very smooth surfaces.

Coverage
3.0 to 3.5 m per litre for 2 coats Coverage may vary depending upon the texture and porosity of the surface.
Shelf Life & Storage
Shelf life is 24 months from the date of manufacturing in unopened conditions. Store in a cool and dry place. Keep away from direct sunlight
Health & Safety Precautions

• Skin contact : Wash skin with soap & water. Remove contaminated clothes.
• On eye contact : Immediately splash eyes with plenty of water. Consult Physician if irritation persists.
• Ingestion : Do not induce vomiting. Never give anything by mouth to an unconscious person. Call a Physician