Write a Review
Our Products
We offer a complete product range of Under Coat Primer for Tiles & Stones and Adhesion Promoter Primer
Dubond's Tile & Stone Primer is a water base nano particle aqueous dispersion. It is designed as a barrier to prevent water, alkali and other compounds from reaching the substrate surface and to avoid efflorescence that can cause surface discoloration especially in cement substrates.
Green Building Rating-Mineral > 30%, Low Emission, Low Ecological Impact, Health Care, Water Based
Areas Of Application-Stones and porous tiles. Interior & exterior Wall & floors Natural porous stones & tiles Concrete surfaces before painting or laying of tiles to prevent efflorescence and providing water resistance Upper substrate acts as a adhesion promoter
Feature & Benefits-Water base nano particle aqueous dispersion It is designed as a barrier to prevent water, alkali and other compounds from reaching the substrate surface.
Method Of Application-Wash the substrate by clean water and allow if to dry apply primer by soft bristle brush and led it to dry 6 to 8 hours. The surface area has been primed now apply any another product.
Shelf Life & storage-6 months in original sealed packing kept in cool and dry place. store in a dry place in the original container.
Health & safety Precautions-Keep out of reach of children. wear suitable protective clothing, gloves, and eye / face protection. after contact with skin wash immediately with plenty of clean water. in case of contact with eyes, rinse immediately with plenry of clean water and seek medical advice.
Additional Information:
Packaging Details : Available in 500 ml, 1 liter , 5 liter, 20 liters , containers.
Dubond's DU Grip is a single part, engineered water based adhesion promoter that develops high, constant levels of performance in non absorbent substrates, compact absorbent substrates, floor in ceramic concretes and residual traces of vinyl adhesives. Du Grip has low i.e. Micro film forming temperature (m.f.f.t.), with advantages over two component adhesion promotes which are found inconsistent at site, suitable only for a specific temperature range and are harmful to the applying professional.
Areas of ApplicationDU Plast 20 is suitable for internal use for high resistance correcting (1mm to 10 mm) of irregular and undulated substrates to be made ready for ceramics, homogeneous tiles, marbles parquet and resilient materials
Areas of ApplicationLevelling of uneven walls made of concrete or cementitious plaster in interiors or exterirors Smoothing of substrates consisting of concrete, stone, brick, cement blocks or cementitious plaster of adequatemechanical strength, in interiors/exteriors for improved adhesion. Reinforced plaster for consolidating unsound masonry imrpoved bonding to smooth substrates with low absorbency. Compensates shrinkage. High durability to aggresive substrates such as sulphates and chlorides. It is impermeable to rains and has calibrated shrinkage. The fluidifying agents reduces water/cement ratio while interstitial crystallizing agent provide stable chemical structurethat is resistant to carbonation, nitrates, sulphates and chloride attracts.
Preparation of SubstratesSubstrates must be stable, dry, free from any rising damp, without cracks, free from dust oil, grease and loose, flaky parts. on substrates which are compact but very absorbent, apply Hydro Prime, Water-based surface insulations, in order to reduce and regulate the level of absorption. In the case of absorbent substrates with weak consistency, apply in double coats without dilution of water.
PreparationPrepare DU Plast 20 in a clean container by pouring in 3/4 of the water required. Gradually add DU Plast 20 to the water, mixing the paste with a low-rev (400/min.) helicoidal agitator. Add water until a homogeneous, lump-free mortar is obtained. The amount of water to be added indicated on the packaging, is an approximate guide.
ApplicationApply Du Plast 20 with a smooth spreader. The high level of thixotropy of the mixture allows for high finishing thicknesses with just one coating. It is generally advisable to apply an initial fine layer, pressing the product down to obtain maximum adhesion to the substrate and to adjust water absorption of subsequent layers. The appearance of he finish will vary depending on whether a smooth steel spreader or a sponge spreader has been used for application. For subsequent laying of ceramics tiles it is always advisable to obtain a roughened, porous surface.
Precautions & LimitationsDo not use DU Plast 20 for levelling purposes or for the correction of substrate irregularities greater than 10 mm. Do not add other binders or additives to the mixture low temperatures and high relative environment humidity lengthen drying times an excessive quantity of water will reduce strength and the drying time before laying hardwood floors and resilient materials. Check residual humidity with a hygrometer calcium carbide. Protect from direct sunlight and currents of air for the first 12 hours. Respect the elastic joints present in the substrate. Do not use on high flexible substrates subjected to thermal expansion, plasterboard, gypsum, on substrates subjected to continuous moisture rising.
Health & Safety PrecautionsDuring application wear protective clothing, gloves and eye goggles suring application. Avoid product to contact eyes and skin Skin Contact : Wash immediately with plenty of clean water, use kerosene or mineral trupentine when the product has dried. Eye Contact : In the event of eye contact splash plenty of clean water immediately and seek medical advice.
Mr. Bharvin Patel (Dubond Products India Pvt Limited)
C-3, 1001 & 1006, Anushruti Tower, S.G. Highway, Thaltej, Ahmedabad, Gujarat - 380054, India
Share us via
