Window Seal Adhesive

Listing ID #4270102

Dubond's Pinnacle is a hi-tech single part adhesive with superior levels of adhesion and deformability. it is a high performance dry set adhesive for use with water or latex for installing ceramic tiles, marble ,stone, any kind of non porous or vitreous tiles or synthetic stone. use with tuffex ad for high performance for interior and exterior
laying and over laying of sites. It has a special function that works specifically to counter conditions such as external pressures on cladding tiles of the skyscrapers and large format tiles with overlaying on existing floors. it is a secure professional method of laying for it has high deformability up to 10 mm thickness.
Green Building Rating

• Mineral > 30%
• Low Emission
• Low Ecological Impact
• Health Care
• Water Based

Areas of Application

• Fixing absorent floor and wall tiles outdoors and indoors.
• cotta, double- fired, single fired ceramic.
• Fixing natural stone and marble, so long as they are not affected by water Fixing on heating floors.
• Fixing poorly absorbent or non-absorbent materials such as single-fired tiles, refined porcelain stoneware and vitrified tiles.
• Spot-gluing insulating panels made of polystyrene, polyurethane foam, rock or glass wool.
• Suitable for fixing tiles: on top of old ceramic tiles or on facades Very good for large format paving slabs.

Features & Benefits

• Eco-friendly,
• High-performance laying, ideal for use in industrial and commercial applications
• Mineral adhesive for high adhesion,
• Pinnacle contains recycled raw materials
• Pinnacle develops an extended open and adjustability time meaning even highly porous tiles can be quickly and safely laid on very absorbent substrates.
• Thicknesses up to 10 mm

Preparation of substrates
In general, cement-based substrates must be free from dust, oil and grease, dry and free from any rising damp, with no loose, flaky or imperfectly anchored parts such as residual traces of cement, lime and paint, which must be totally removed.
The substrate must be stable and without cracks, must have already completed curing hygrometric shrinkage and must present suitable mechanical resistance levels. Undulated areas must be corrected with suitable smoothing and finishing products.
Application

• Prepare Pinnacle in a clean container, first of all pouring in a quantity of water equal to approximately .of that which will be required.
• Gradually add Pinnacle to the water in the container, mixing the paste from the bottom upwards with a low-rev ( 400 RPM /min.) helicoidal agitator. Then add more water until the desired consistency is obtained, the mixture must be homogeneous and without any lumps. For best results and to mix larger quantities of adhesive, a stirring device with vertical blades and slow rotation is recommended.
• Always use appropriate size of trowell with respect to the tile size and the density of the tile.
• Spread the adhesive over a surface area which will allow for laying of the surface materials within the indicated open time and check for suitability of the adhesive at regular intervals, the open time may vary considerably during the same operation, depending on various factors such as exposure to sunlight, air currents, absorbency of the substrate, temperature and relative humidity of the atmosphere.
• Press down each tile to allow for complete, uniform contact with the adhesive. In the case of laying in environments subject to heavy traffic or in outdoor locations, the double-spread technique must be used, to ensure 100% coverage of the rear of the tiles.

Precautions & Limitations

• Do not use on gypsum-base plasters and anhydrite screeds without the use of HydroPrime professional concentrated, waterbase, surface insulation product;
• On heat-radiant slabs,
• High flexible substrates;
• On plastic or resilient materials,
• On wet surfaces or substrates subject to moisture rising.
• Metals and wood;
• Do not use the adhesive to correct substrate irregularities greater than 10 mm
• Lay and press tiles onto fresh adhesive, making sure it has not formed a surface film
• Protect against direct rain and freezing for at least 24 hours
• The temperature, ventilation and absorption of the substrate and covering materials may
• vary the adhesive workability and setting times
• Use a toothed spreader suitable for the format of the tiles
• Use the double-spread technique for all outdoor laying