Bath Linens #1429614

High temperature bath is suitable for calibration of temperature sensors, polymer studies etc. Polished stainless steel inner chamber, Mild steel outer chamber finished in pleasing two colour scheme. Glass wool insulation. Proportional, Fully solid state control of temperature. Fully automatic action. Fine control facility for high accuracy Pt-100 sensor. Combination Digital set point & readout with 13mm LED Immersion heater. Stirrer unit to maintain uniform tank temperature. Accuracy +/-0.5% of full scale +/-1 digit. Control Accuracy +/-0.1 deg C to +/- 1 Digit at 100 deg C. Working size : 250mm L X 200mm W X 200mm D

• Coil for circulation of chilled water
• Calibration certificate traceable to national standard.
• Resolution of 0.1 deg C for Max Temp. range of 300 deg C

Used to maintain in water the Marshal specimens to be tested at 600+ 10 (Asphalt specimens) or 37.80+ (Tar Specimens) as prescribed by the specifications. The Same Water bath can also be used for Penetration test, Stripping test or even soundness test of cement with the use of additional accessories. Available in different sizes and temperature control system.

Used for determination of Kinematic and intrinsic viscosity of fuels, lubricants & petrochem raw materials at constant temperatures in accordance with ASTM D 445 and other equivalent methods. Available in two versions, to work at above ambient temperature and below ambient temperature.

General Descripation & Specifications

Double walled, outer chamber made of G.I. - powder coated, with removable toughened Glass window panel, inner chamber made of S. S, FHP motorised stirrer for uniform temperature, Dual Display Microprocessor Based Digital Temp. Controller with PT-100 sensor. Temperature range from 5 C above ambient to 100 C., Control accuracy 0.1C. Below ambient Viscosity Baths are fitted with Refrigeration system (Temperature Range : 10C to 100C). The Baths can accommodate 2 / 4 / 8 Viscometers with varying tank volumes.

• Stainless steel bath
• Temperature controller (Thermostatic/Digital)
• Immersion electric heater
• Constant speed Pump cum stirrer
• Carriage holding up to three standard briquette moulds
• Electric motor with gear mechanism
• Stainless steel scale and pointer
• Control Panel

Reverse Flow Viscometer

The viscometer is made of clear borosilicate glass free from visible defects. All glass tubing used in the construction of a single viscometer is of the same composition and the finished instrument is thoroughly annealed. The design and details of the viscometer are given at side. The size, approximate constant and Kinematic Viscosity is as per table.

Cannon Fenske Viscometer

For opaque and transparent liquids : detailed drawings of the reverse flow Cannon-Fenske viscometer is given in the figure. The size, approximate constant and kinematic viscosity range, is given in the table.

Double walled inside of stainless steel with thick glasswool insulation, temp. range 5 C above ambient to 200 Dual Display Microprocessor Based Digital Temp. Controller with an accuracy of + 1C. Fitted with stirrer on the side of the bath at the top. Working Size : 300 x 300 x 250 mm.
Inside Stainless Steel OR Inner/Outer Stainless Steel

FOR PILOT PLANT:

Double walled construction, outer mild steel or stainless steel & inner chamber made of stainless steel argon welded. Temp. range 50 deg C to 300 deg C, controlled by energy regulator or Digital Temperature controller.

WORKING SIZE (CM) (L x W x D):

40 X 28 X 10

30 X 20 X 10

OPTIONAL:

Optional Digital Temp. controller with sensor.

For procedures requiring constant temperature, uniform shaking and controlled atmosphere. Double walled, inside stainless steel, Outer made of CRC/G.I.-Powder coated, glasswool insulation.Temp. control by Dual Display Microprocessor Based Digital Temp. Controller from 5C above ambient to 100C 1 C. Continuous shaking is controlled by a geared driven mechanism. The bath has an oscillating tray, riding on ball rollers and drive motor with variable speed control. Shaking speed is 40 to 140 cycles per minute. Teflon coated shaking rack highly resistive to heat and chemical.

Optional Accessories

• Shaking racks for 25 ml / 50ml / 100ml / 250ml / 500ml / 1000ml flasks, interchangeable
• Test tube rack for 25 mm dia X 35 nos. test tubes
• Dual Display Digital Timer with alarm
• Programmable microprocessor based dual display digital temperature controller
• Digital speed meter to indicate RPM/ Oscillation

This Equipment is to speed up the process with ease and accuracy to prepare cylindrical specimens for Marshal Stability Testing Machine. The compactor has been designed to simulate hand compaction as described in ASTM D1559. This apparatus automatically compacts the sample and stops after preset number of blows has been completed. The Compactor gives Uniformly and accurately compacted marshal moulds for reliable testing.

General Descripation & Specifications

It is a motor driven mechanical compactor useful for compaction into 100 mm dia moulds. It is fitted with a compaction rammer of 98.5mm dia, weighing 4.535 kg. with a free fall of 457 mm. The rammer assembly is provided with a ratchet and pawl arrangement to lift it from the top of the test sample. When the rammer reaches the required height the pawl release the rammer which falls freely on test specimen. The release mechanism is connected by an arm moving up and down which is connected to a reduction gear coupled to the motor through another arm. An automatic blow counter fitted to the compactor is used to set the number of blows. The Compactor is supplied complete with wooden pedestal. Suitable to work on 220V, 50 Hz, AC single phase.

Used for determination of Kinematic and intrinsic viscosity of fuels, lubricants & petrochem raw materials at constant temperatures in accordance with ASTM D 445 and other equivalent methods. Available in two versions, to work at above ambient temperature and below ambient temperature.Double walled, outer chamber made of G.I. - powder coated, with removable toughened Glass window panel, inner chamber made of S. S, FHP motorised stirrer for uniform temperature, Dual Display Microprocessor Based Digital Temp. Controller with PT-100 sensor. Temperature range from 5 C above ambient to 100 C., Control accuracy 0.1C. Below ambient Viscosity Baths are fitted with Refrigeration system (Temperature Range : 10C to 100C). The Baths can accommodate 2 4 8 Viscometers with varying tank volumes.C