We are the leading manufacturers, exporters and supplier of this products.

The presence of moisture in palletized plastics results in impairments such as poor surface quality, internal voids & loss of physical properties. These defects can be overcome by removing the moisture by preheating the plastic material using ELMEC PRE-DRYERS

Features

1. Rugged construction ensures longer life


2. High speed blower for effective and uniform drying of granules


3. Solid state Temperature Controller/Thermostat


4. Complete heat insulated walls


5. Modular type heating element for effective and efficient heat transfer


6. Low power consumption

Thermo Couples

Elmec thermocouples are specially made under stringent quality conditions

Features:

1. Available for all possible applications


2. Can be made to customers specifications


3. Types-J, K, T, E, R and resistor sensor


4. Supplied with calibration certificates and accessories


5. Available in Plain, Bayonet, Washer, Leaf and Ring types

When Ordering Please Specify :

1. Type


2. Cable length.


3. Tip diameter & length


4. Drawing for special type configuration.

1. Compacted Heating Elements for efficient heat transfer & longer life.


2. Nichrome 80/20 or Kanthal Heating Coil.


3. Heater tube sheath S.S. 304 .


4. Imported High grade MgO powder insulation for best heat transfer and electrical insulation.


5. S.S.Terminal pins to prevent fusing and burning at terminals.


6. Quick heating therefore economical and saves power.


7. Center supporting rod made of M.S. for low power and S.S. for high power heaters.


8. Durable and long lasting.


9. Easy replaceability of individual elements.

Elmec Hot Runner Controllers are efficient and economical. Our Multi zone Hot runner Controllers are by single temperature control modules assembled in a cabinet. SSR controlled outputs (or) Thyristor controlled outputs to control Hot runner Heaters & Manifold Heaters are available.

1. For Controlling Hot Runner heaters & Manifold Heaters in Plastic Injection Moulds.

Elmec produces hot runner heater by placing nickel chrome resistance wire in the tube made of nickel steel filled with magnesium oxide powder for effective heat transfer. The heaters are made to acquire strength so that it could be bent into any shape. Tape Heaters, Heater Pads and Thermocouples are also available

1. Sheath temperature upto 800oC


2. Higher watt densities


3. Build in Type "J" (or) "K" Thermocouple


4. Available in following cross sections : 3mm X 3mm, 3.3mm X 3.3mm, 3.7mm X 3.7mm, 4.5mmX4.5mm, 4.2mm X 2.2mm, 3.2mm X 1.8mm, O 1.8mm, 3.3mm, 3.7mm


5. Rugged & Durable Construction


6. Available as per customer's specifications

1. Moulds & Dies


2. Nozzle heating


3. Sprue Bushing

HOW TO ORDER COILED MICRO TUBULAR HEATER

1. Watts & Volts


2. Cross Section


3. ID, OD & Length


4. Termination style


5. Thermocouple if required Specify Type "J" (or) "K" Grounded (or) Ungronded


6. Number of coil in L1, L2 & L3


7. Coil total Length T.L, L1, L2, & L3


8. Connection lead option, lead length and lead orientation


9. Drawing or sample for special type configuration

Elmec manufactures furnaces for laboratories and for various other applications. Furnace to reach maximum temperature upto 1200C can be supplied. We also manufacture large capacity furnaces as per customers specifications and applications.

For more information on technical specifications consult ELMEC.

One of the important factor, to be considered in moulding of engineering thermoplastic materials is mould temperature. It is very essential to maintain optimum temperature in the mould while processing, to obtain perfect and precision moulded component. Elmec Heaters & Controllers has designed a compact mould temperature controller that heats and cools the mould to maintain optimum temperature in the mould.

1. Compact and fully automatic unit.


2. Circulating media is oil (water -optional)


3. Automatic water cooling to maintain thermal stability.


4. Safety Thermostat to safeguard, the unit in case of failure of temperature controller.


5. Efficient temperature control up to 2 C ( 0 C is also possible)

Control Panels for controlling heater output are offered with digital/analog temperature controller, thermocouples, and necessary indicating devices. They can be made strictly as per customer specifications

The electrical connection is available with cable outlets or post terminals covered with junction box. Nickel Chrome Resistance Wire. Ceramic Fiber Insulation reduces power consumption by 20 to 30%, Available with heating & cooling combination.

Elmec Insulation jackets are made up of 3 layers. Inner layer is made of fibre glass cloth, Middle layer is made of 50 mm thick fibre blanket, Top layer is made of abrasion proof glass fabric which resists both dirt and plastic material. All these material can withstand temp upto 600 C. These insulation jackets are made with holes and cutouts wherever it is required and so it is easy to install over the barrels of Injection, Extrusion and Blow molding machines.

1. Reduces power consumption from 20% - 30%


2. During the process, the heaters are switched off for long time, thereby increasing heaters life.


3. Working atmosphere remains more comfortable.


4. Initial heat up time decreases considerably.


5. These insulation jackets have special fixing arrangements, so that they can be easily removed and fixed.


6. These insulation jackets can serve for a very long period, due to abrasion proof materials.

1. Outside diameter and width of the heater


2. Type and position of the terminal


3. Drawing where special type of holes or cutout required

The moisture in the Plastic Resins (Hygroscopic and Non-Hygroscopic) will effect the surface finish and quality of the molded component. We have designed a compact and economical HOT AIR HOPPER DRYER to overcome this problem.

Features

1. Drying capacities ranges from 25 Kgs to 100 kgs


2. Direct Machine mounting


3. Tubular type heaters for longer heater life


4. Solid state temperature controller for reliability


5. Process air temperatures to 150C and higher with options


6. Fiber glass insulation optional


7. Low power consumption


8. Specially designed diffuser cone for uniform heating and drying


9. Detachable air distribution system for easy cleaning

Hopper Dryer Attachments

We offer an unique system to convert existing hopper into dryer just be replacing the top lid of the existing hopper.

We are the leading manufacturers, exporters and supplier of this products.

The presence of moisture in palletized plastics results in impairments such as poor surface quality, internal voids & loss of physical properties. These defects can be overcome by removing the moisture by preheating the plastic material using ELMEC PRE-DRYERS

Features

1. Rugged construction ensures longer life
2. High speed blower for effective and uniform drying of granules
3. Solid state Temperature Controller/Thermostat
4. Complete heat insulated walls
5. Modular type heating element for effective and efficient heat transfer
6. Low power consumption

Thermo Couples

Elmec thermocouples are specially made under stringent quality conditions

Features:

1. Available for all possible applications
2. Can be made to customers specifications
3. Types-J, K, T, E, R and resistor sensor
4. Supplied with calibration certificates and accessories
5. Available in Plain, Bayonet, Washer, Leaf and Ring types

When Ordering Please Specify :

1. Type
2. Cable length.
3. Tip diameter & length
4. Drawing for special type configuration.

1. Compacted Heating Elements for efficient heat transfer & longer life.
2. Nichrome 80/20 or Kanthal Heating Coil.
3. Heater tube sheath S.S. 304 .
4. Imported High grade MgO powder insulation for best heat transfer and electrical insulation.
5. S.S.Terminal pins to prevent fusing and burning at terminals.
6. Quick heating therefore economical and saves power.
7. Center supporting rod made of M.S. for low power and S.S. for high power heaters.
8. Durable and long lasting.
9. Easy replaceability of individual elements.

Elmec Hot Runner Controllers are efficient and economical. Our Multi zone Hot runner Controllers are by single temperature control modules assembled in a cabinet. SSR controlled outputs (or) Thyristor controlled outputs to control Hot runner Heaters & Manifold Heaters are available.

1. For Controlling Hot Runner heaters & Manifold Heaters in Plastic Injection Moulds.

Elmec produces hot runner heater by placing nickel chrome resistance wire in the tube made of nickel steel filled with magnesium oxide powder for effective heat transfer. The heaters are made to acquire strength so that it could be bent into any shape. Tape Heaters, Heater Pads and Thermocouples are also available

1. Sheath temperature upto 800oC
2. Higher watt densities
3. Build in Type "J" (or) "K" Thermocouple
4. Available in following cross sections : 3mm X 3mm, 3.3mm X 3.3mm, 3.7mm X 3.7mm, 4.5mmX4.5mm, 4.2mm X 2.2mm, 3.2mm X 1.8mm, O 1.8mm, 3.3mm, 3.7mm
5. Rugged & Durable Construction
6. Available as per customer's specifications

1. Moulds & Dies
2. Nozzle heating
3. Sprue Bushing

HOW TO ORDER COILED MICRO TUBULAR HEATER

1. Watts & Volts
2. Cross Section
3. ID, OD & Length
4. Termination style
5. Thermocouple if required Specify Type "J" (or) "K" Grounded (or) Ungronded
6. Number of coil in L1, L2 & L3
7. Coil total Length T.L, L1, L2, & L3
8. Connection lead option, lead length and lead orientation
9. Drawing or sample for special type configuration

Elmec manufactures furnaces for laboratories and for various other applications. Furnace to reach maximum temperature upto 1200C can be supplied. We also manufacture large capacity furnaces as per customers specifications and applications.

For more information on technical specifications consult ELMEC.

One of the important factor, to be considered in moulding of engineering thermoplastic materials is mould temperature. It is very essential to maintain optimum temperature in the mould while processing, to obtain perfect and precision moulded component. Elmec Heaters & Controllers has designed a compact mould temperature controller that heats and cools the mould to maintain optimum temperature in the mould.

1. Compact and fully automatic unit.
2. Circulating media is oil (water -optional)
3. Automatic water cooling to maintain thermal stability.
4. Safety Thermostat to safeguard, the unit in case of failure of temperature controller.
5. Efficient temperature control up to 2 C ( 0 C is also possible)

Control Panels for controlling heater output are offered with digital/analog temperature controller, thermocouples, and necessary indicating devices. They can be made strictly as per customer specifications

The electrical connection is available with cable outlets or post terminals covered with junction box. Nickel Chrome Resistance Wire. Ceramic Fiber Insulation reduces power consumption by 20 to 30%, Available with heating & cooling combination.

Elmec Insulation jackets are made up of 3 layers. Inner layer is made of fibre glass cloth, Middle layer is made of 50 mm thick fibre blanket, Top layer is made of abrasion proof glass fabric which resists both dirt and plastic material. All these material can withstand temp upto 600 C. These insulation jackets are made with holes and cutouts wherever it is required and so it is easy to install over the barrels of Injection, Extrusion and Blow molding machines.

1. Reduces power consumption from 20% - 30%
2. During the process, the heaters are switched off for long time, thereby increasing heaters life.
3. Working atmosphere remains more comfortable.
4. Initial heat up time decreases considerably.
5. These insulation jackets have special fixing arrangements, so that they can be easily removed and fixed.
6. These insulation jackets can serve for a very long period, due to abrasion proof materials.

1. Outside diameter and width of the heater
2. Type and position of the terminal
3. Drawing where special type of holes or cutout required

The moisture in the Plastic Resins (Hygroscopic and Non-Hygroscopic) will effect the surface finish and quality of the molded component. We have designed a compact and economical HOT AIR HOPPER DRYER to overcome this problem.

Features

1. Drying capacities ranges from 25 Kgs to 100 kgs
2. Direct Machine mounting
3. Tubular type heaters for longer heater life
4. Solid state temperature controller for reliability
5. Process air temperatures to 150C and higher with options
6. Fiber glass insulation optional
7. Low power consumption
8. Specially designed diffuser cone for uniform heating and drying
9. Detachable air distribution system for easy cleaning

Hopper Dryer Attachments

We offer an unique system to convert existing hopper into dryer just be replacing the top lid of the existing hopper.