Our Products #4621360

For Centrifugal Cleaning of pulp the centri Cleaner are available in two series i.e. 600 and 620 which has a capacity range extending from 120 LMP to 2400 LMP. Its high separation efficiency and the flexibility permit it to be accommodated to any capacity. For ease of maintenance and replacement, all bottles are made in two or three flange connected parts.Centri Cleaner bottles are available in S.S. Construction with underflow nozzle of nylon ceramic.

Most modern design of Thickener Drum having a few number of spiders and perforated Plate fitted with landing and filter wire. This design is robust and requires very little maintenance.

Effective separation of heavy and light impurities.Low fibre lossThe body is made out of mild steel with and option of internal ling of stainless steel. The rotor and screen (2-4 mm perforation) are made of stainless steel. A forced vortex is formed in the turbo by the rotor. Heavy contraries are carried outwards by centrifugal force into the junk trap while light contraries get collected in the centre which travels out through the light reject nozzle. The accepted stock passes through the screen fitted behind the rotor.

This machine required for cutting sized body blank & top bottom blanks from a sheet or a coil. This basic structure is steel fabricated that gives it an extra strength and rigidity. For smooth & trouble free operation, an appropriate lubricating system is provided everywhere. The shearing blades are made out of best quality material, hardened and ground to its best standards, both the blades are reversible type so that all the four edges can be utilized, giving the blades an extra lift. All the moving parts (Bushing) are made up of phosphorus bronze. The maximum speed is given to achieve more production.

Edge Grinding is a very special operation in manufacturing of Drums & Barrels, because some amount of material is to removed from the edges if the body, which give advantages to Welding operations (removes dirt, oiliness, etc.), extra strength to the weld and a leak proof joint. Flanging operation. End seaming operation (lesser thickness of side seam overlap). Maximum parts of the machine are steel fabricated. It can absorb all jerks & vibration caused due to the grinding wheel. Proper dressing arrangement is for smooth grinding. The entire machine is divided in 3 parts as Centre table on fixed guide rails by means of pneumatically operated long cylinder Right hand side grinding unit Left hand side grinding unit. All the units are properly assembled; micro setting arrangement is given for maintaining highly precise gap between the grinding wheels.

The vibrating Screens manufactured by us are used for effective screening of pulp. These screens can be widely used in different locations of the paper Mill, Viz. as a knotter ahead of paper Machine making heavier grades of Wrapping Papers: as a fine screen for straw pulp beaten in Hollanders and in conical Refiners as s fine screen for waste paper processed in pulpers as a knotter for havier grades of board.

This machine is required for making body balk in round roll forms, before spot- weld & side seam weld. The performance of welding & shape of the drum & barrel is totally dependent on this operation. The machine shown here gives perfect round trouble free operation, it can be operated easily & can be adjusted rapidly for drum bodies of various diameters. The rolls are of best quality sheet and run on gun metal bearing, machine is designed to be rolled on wide range of diameters of bodies, different gauges, and hardness of material. Appropriate proper lubrication is provided.

PUMPS are specially designed to handle pulp in paper and board industries. They are horizontal shaft back pull out design. Dismantling and assembly is easy and quick without disturbing suction and delivery pipe lines.

This machine is strong enough and well capable of shearing to specified thickness & material with ease as it is made out of special graded material. It is heavy-duty & has a stable structural design on this machine we get precise circles without having any cut or rough edges.

The illustrated model is for side seam welding to full length of the hollow drum & barrel body. The machine body is steel fabricated with extra ribbings & heavy structural design with heavy duty transformer used as the main power for continuous welding operations. The machine is equipped with upper & lower weld wheel made out of good quality Beryllium copper; its bearing shaft, housing etc. are all made of Brass & Copper. D.C variable drives with electronic speed control, water cooling system with necessary valves. Multi tapping system, welding transformer for load selection, best available pneumatic equipment like power cylinder piping & D.C valve etc. the logic control with timer & heat control standard card for getting best possible welding quality. Microprocessor is also available on request with a bypass connector switch is provided.

This machine gives beading to the drum or the barrel. This bead gives an extra strength to the body cell. It also contains sets of segments made out of finest quality heat treated steel along with hydraulic power pack of all standards parts, high quality flexible tubing, and logic & control panel. Hydraulic Cylinder etc. of this machine is very fast & rejection rate is absolutely nil compared to rotary type beading machine. A separate power pack is provided. In case of lower production rate, single tooling bead expander can be used. Double beading machine gives both beads at one stroke. Nominal, unskilled operator can also operate this machine.

The ATS type Pulper is suitable both for dissolving cellulose waste paper board as well as broke from the machine.This is a continuous type Pulper.The Pulper is provided with 304 S.S. Screen and S.S. Casting rotor.The Pulper is available in four standard sizes. _3M3, 5M3, 6M3 and 8M3.Two stages belt conveyor is provided for mechanized feeding.

The rocker arm spot welding machine is an important machine in manufacturing Drums & Barrels. It is better to give some spots to the body sides before side seam welding operation. The machine can also be used for spot welding the handles etc. this machine is specially designed with a longer arm, better rated transformer & electronic timer, also given are various tapping to transformer for welding current selection enabling universal use.

High Consistency Pulper with Helical RotorMedium Consistency PulpersUTM Pulpers (Broke)Highly Consistent slushing of Pulp and efficient defibersation

This machine is required for giving flange to the drums or barrel, by changing the rollers, the same machine can be used for single beading too. The illustrated model has flanging tool where in one stroke, we get one side flanging & by turning the body we get another side flanging. Body is fabricated with heavy.

This machine is required for seaming of top bottom with body. We can also get triple seaming from this it, where two seaming rollers (made out of good quality steel duly hardened & ground) come one after another resulting in strongest leak proof seaming. On special order, ejection of solution can be incorporated. With the help of following equipments: Foot operated switch, location clogs, smooth steady rotating table pneumatic cylinders, limit switch logic control, Power pack. Table Stroke hydraulic cylinder, electro magnetic clutch brake unit strong enough, chuck drive, and proper grooved seaming roller assembly.

The machine is required for giving flange to the drum or the barrel. For getting good seam, proper even flange is essential. This machine contains two flanging tools made out of good quality steel, which are heat treated and ground is also has a separate hydraulic power pack of all standards parts, high quality flexible tubing, logic, and control panel, high quality hydraulic cylinder etc. the main advantages in this is that rejection rate is almost nil and gives both the flange simultaneously, it also gives very fast trouble free production, and unskilled operator also can operate this machine. Operation is very safe because drum does not rotate. We get even flange and very precise diameter of drum and barrel body, no bucking, no unevenness of flange no wrinkle to flange (usually all this defects are experienced in rotary flanging machine.)

It does an excellent job of final stock cleaning single cylinder and construction. Permits easy inspection and maintenance. The hydra foil bass can be easily adjusted. Non-contacting air foil bass continuously sweep the inner surface of screen creating a pulsating action which increases efficiency of cleaning. Prevents plugging and effects uniform fibre dispersion. It does an excellent job of final stock cleanup, removing, pins, scale, shives and other unwanted material from the stock.Deflocculates fibre bundles in the stock improves formation on the wire.Increases Production there are fewer breaks because stock lumps and slime sluges are eliminated.Protects against felt and wire damage cause by foreign objects.Relieves foaming conditions.Plus many others.