Other Products / Services #3623441

Prefabricated Industrial sheds provided with EOT cranes and also without cranes for warehouse and storage.

Single wire Granite Dressing machine with hydraulic tensioning of wire , provided with rotating trolley.

The most advanced technical requirements which ensures the best accuracy, rigidness, power, durability and simplicity of the operations making possible a high working output achieved by particular features i.e., casting columns of extreme bardness with tubular section ensuring an absolute rigidity of work, while high capacity bearing make the column rotate inside the steel sleeve make possible the movement from top to bottom . Pressure apparatus - which makes use of the flexibility of the arms and supplies the polishing apparatus - which makes use of the flexibility of the arms and supplies the polishing beads with an adjustable pre - loading at will, very useful for milling operations. Motorized vertical displacement adds versatility to the machine reducing the operators works to the minimum possible .

The circular saw for the building industry, is a simple and sturdy machine useful both for marble and granite and other similar stones. The operation of the machine is simple and does not require any skilled operators. The longitudinal cut is manually fed (Optional-can be power driven) using a hand wheel or pull handle. The cutting disc is a direct drive from the electric motor. The machine consists of a steel base which supports two horizontal chromium plated bars with a blade carrier running on linear ball bearings giving perfect accuracy. The blade rise and fall is regulated by means of a hand wheel located on top of the carriage. The saw bed consists of an integral water reservoir built of stainless steel, and water is circulated by means of submersible pump complete with filters. The saw head is inclinable and is locable to produce inclined cuts from 0 to 45 degree.

Block Dressing Machine (mono Blade)
The main structure of the Machine consist of pillars, Guide frame Connecting rod, tie beam etc. are manufactured from heavy steel plates, machined & Ground to tolerance limits. Balanced from high accuracy along with precise alignment of various mating parts ensures smooth operation of the Machine. Feed rate of the machine is shown by the digital feed meter.
Hydraulic tensioning device is ensures that machine starts only when the blade is preset to the tension required. The main motor is interlocked with water pump and does not start in case water is insufficient or not available at the blade. Proper safety device ensure high dependability of the machine

Waste water or slurry coming from the procesing lines (marble, granite, agglomerate, ceramic, cement, aggregate, etc.) is conveyed by means of piping to the collection tank, where a submersed motor- driven pump, controlled by a limit level probe, auto- matically convey the slurry to the decanter . On its way to the decanter, the slurry is treated with flocculent (a biodegradable chemical), which is dissolved in the upper tank of the flocculant station by means of an electric mixing device and drained into the lower tank, where a batching and drained into the lower tank, where a batching pump injects the flocculant into the decanter feed line. The flocculant acts on the sediment particles contained in the slurry, causing them to stick together; this results in a shorter sedimentanion time. The slurry is fed into the decanter through the inner parallel pipes and its speed is varied in the tapering cone section. The unpolluted water rises through the decanter's central ring into the specially shaped upper channel, from where it passes through the piping into the clean water collection tank. From here a pump would have to be utilised to re-cycle the clean water back to processing line. The sludge deposited at the bottom of the cone in the decanter is removed automatically at regular intervals by a pneumatic valve fed by a compressor. The sludge is then conveyed by piping to the sedimentation collection tank, where a probe unit controls its level. This tank is equipped with an electric mixing device to prevent the precipitation of solids. Form the sedimentation collection tank, the sludge is fed to the filter press by means of a high pressure abrasive resistant pump. In the filters the filter press, plate - type with chambers, the liquid still contained in the sludge is separated and returns to the waste water tank by piping, while the solids are retained by the canvas filters inside the plates. Filter clogging level is recognized by a sensor in the filtrate tank, which consents to the opening of the filter panels, thereby allowing the discharge of the dehydrated mud. The mud is collected in a solid form at the bottom of the filter press. All the processing cycle is completely automated.

The machine consists of a flywheel which drives the frame through a set of cams mounted on both end of the shaft of machine is made of high endurance steel supported on two bearing blocks. The drive is obtained by a slip ring motor through a flat belt which ensures gradual starting of machine the heavy saw frame is designed to with stand stresses and tension load and vibration.

Description of High Speed Diamond Gang Saw Model HT-80:-
1. DRIVE SYSTEM :- This machine is consisted of a heavy and well balanced fly wheel suitable for adjusting alternatives movements. The shaft of the fly wheel is made by special high endurance steel, mounted on proper pillow boxed with antifriction bearings. The two cams of the cranks are mounted at the both ends of the axle for imparting the alternative motion of blade holder frame to both connecting rods. The Drive is obtained by a slipring type powered main electric motor through a flat belt. The system ensures the gradual starting of fly wheel with easy and smoothness.

2. SAW FRAME :- The Heavy saw frame is designed to withstand tension load all stresses and vibrations possible during operation so that the as made geometry of blades is maintaine in the frame for an efficient and distrotion free cutting of slabs. Four special sliding guide unit/ pendulam type are provided for obtaining the rectilinear movement of the blades holder frame. These sliding guide units having self aligning system remain in constant oil bath and ensures remarkable precision during alternative motion of blades during the operation.

3. COLUMNS :- For supporting the frame consisting of the whole group of blades, four heavy columns of stiffened and shaped steel are provided which are designed to with stand all possible stresses and vibrations developed by the movement of frame during operation.

4. TROLLEY :- The trolley performs up and down motion with the marble block for cutting operation. This is supplied with four guides in pressure sliding prismatic precise slides mounted on four columns. This is designed for perfect alignment between the platform & saw frame. The up and down motion is produced by powered jack-screw mechanisms, for this purpose four big screws are incorporated which receive the feed from a motor variator reducer unit with consent to obtain a variation of sawing speed as required depending on the type and quality of the block.

5. CONTROL PANEL :- We also provide a reading desk with all control devices for ensuring a complete control over the electrical functions for desired safe operation.