We are amongst the eminent names in the industry, engaged in offering a complete range of Laboratory Testing Equipment. This range is manufactured by using the quality tested raw materials under the supervision of our highly skilled professionals. Used in laboratories for testing and experimentation purposes, our equipment has been acknowledged for its great performance, long service life, and accuracy. Our offered product can be availed at the industrial leading prices.

Owing to the vast experience and state-of-the-art infrastructure we are instrumental in providing a wide array of Powder Management System. The system offered by us is manufactured our experts using quality checked components and advanced technology in compliance with set industry norms. Moreover, our offered range can be availed in a wide range of specifications, as per the requirements of our esteemed clients.  We provide this system at market leading prices within promised time frame.

System : The powder collected in the recovery bins of Multicyclone is fed to recycled powder hopper through a sieve. The fresh powder is stored in a separate fresh powder hopper. Powder from both these hoppers is fed to the second sifter assembly through ejector pump and minicyclone. Here the powders gets well mixed and then gets collected in the mixed powder hopper. This hopper will feed powder to the applicators. As recovered and fresh powder is sieved again, total coating quality is improved.

Proportionate Mixing :

• The mixing of powder can be done proportionately either manually or automatically. In the manual system, each ejector pump will have separate powder control, which can be set manually to the desired mixing ratio. In the automatic system, the operator is required to feed only desired mixing ratio say 80 : 20 or 70 : 30.
• Due to continuous powder loop formation manual handling is avoided and consistent powder supply is achieved with improvement in quality.

Post Filter

• 98.5% efficiency of the Multicyclone helps in maximum utilization of chargeable powder. But to comply with Pollution Control Laws, the 1.5% powder fines are required to be arrested. The post filter arrests this powder and gives out breathable air.
• A number of filter cartridges are mounted inside the sealed metallic chamber. The air enters the chamber and the filteration occurs 'outside in'. Periodic purge removes the powder and clean the cartridge. Clean air is given out through the blower outlet.

Integration Concept
Booth - when integrated with Equipment and post filter gives :

• Automatic mixing of fresh & recovered powder.
• Automatic feeding of powder to spray gun.
• Automatic on-line sieving.
• Prevention of entry of fines in atmosphere.

Recycling system : The recycling system helps in optimum utilization of powder. Powder is recycled automatically back to the gun through the sieving machine.

Sieving Machine Sifter : This high sieving rate machine can accommodate powder flow from three Multi Cyclones. The sieves are available in variety of sizes catering to different powders. Sufficient dampening provides noiseless operation.

Technical Specifications :

• Standard Mesh - 60
• Optional Mesh - 80, 100

Ejector Pump :
This high volume capacity pump sucks powder from the multi cyclone recovery bins delivering it to the sieve chamber through the mini cyclone.

Technical Specifications : Standard Mesh - 60

Hopper : Carbon Steel Powder containers with provision for fluidization are used as reservoir to supply powder to spray applicators.

Technical Specifications :

• Standard Sizes : 20 kg, 40 kg, 80 kg, 120 kg.

Mini Cyclone ;
Mini Cyclone feeds powder to the sieve and then to the hopper. During the process, fines get separated and delivered back to the powder booth to avoid air pollution.

Being an established brand in the industry we are offering Sand Blasting Machine to our valued clients. The product we offer is excellent in quality, as it is manufactured by using the excellent quality materials along with the latest technology. The product is designed for precision and excellence by our experienced team of professionals.  Our product is highly demanded, as it is used for various applications like cleaning of molds, putting grains on the molds, preparing the surface for painting, coating, and much more. We are offering this machine at a very marketable rate.

Portable Abrasive Blaster

• The portable abrasive blaster are safe, high productivity systems designed for use with a wide range of abrasive media. The operation is performed on metals, glass, ceramics, plastic and stone.
• The machine works on pressure blasting principle, consist of a blast generator. The abrasives are filled at the top of machine when machine is not working and blast generator is not pressurized. At the top, a vibrating sieve is provided to sieve the abrasive filled. The oversize abrasive and debris are retained on the screen, thus prevent the choking of blast line. When mushroom valve is opened the abrasive will get transferred to blast generator for blasting. The mushroom valve gets closed when compressed air is switched on and abrasive storage tank gets pressurized, for free fall of abrasive into the mixing tube. From mixing tube the abrasive is carried away by compressed air to the nozzle for blasting. The Blast Generator is fabricated from MS Steel plate of thickness not less than 6 mm as per IS-2825 and hydraulically tested for 250 psi.

Our vision to be known as the best in the market has enabled us to offer and excellent quality Shot Blasting Machine to our valued customers. We manufacture this product keeping in mind the needs and demands of the customers. The product we are offering is excellent in quality and well designed. The offered product is used in various industries for the purpose of cleaning or preparing a surface. We are offering this product at a very marketable rate.

Details : About Blast Cabinet Blast Cabinet is an enclosure which houses the abrasive propelling mechanism (blast gun), holds work in position and confines flying abrasive particles and dust. Features of Blast Cabinets Machine meets ISO Standards All cabinet models are rubber lined inside large vision window. vision glass is protected by a wire screen against abrasion and glass is easily replaceable. Easy fitting of accessories like nozzles, hoses etc. Whenever required at site. New ergonomic cabinet is designed to snake operator relaxed while working. Blasting start/stop is through foot valve so that both hands of operator are free to maneuver the job or blasting nozzle. Air pressure gauge, air pressure regulator, moisture separator (except Wet Blaster) and an air gun is provided as standard fitting. Simple operation and simple installation as the machines are ready to operate when connected with airline and electric supply. foundation or pit for installation not necessary. fabricated from heavy gauge mild steel, folded and welded construction. It incorporate sealed hand holes ans gasketed doors to ensure that dust will not escape outside. Environmentally clean and friendly as dust collection device is attached so only clean air is 1 discharged to atmosphere. Noise level of fan is kept below 80 dBA at operators position. proper ventilation is provided for clear visibility while blasting. Doors are provided with cam lock system, which seals the door across the width by operating a single lever, and are easy to open / close. High lums transfer good illumination also proper ventilation for clear visibility.

Suction Blaster
Suction Blaster is the simplest and most effective way to remove corrosion and old paint. Suction Blaster is a clean, dust free sand blaster that leaves the surface cleaned and well prepared for painting, filling etc. When the cabinet and power module are correctly set-up, the cabinet is ready for operation by actuation of the foot pedal. Fully depressing the foot pedal causes air to flow through the blast gun. Air moving through the gun draws media into the blast gun mixing chamber. The media mixes with the air and is propelled out the nozzle. After striking the object being blasted, the blast media, along with fines, dust, and byproducts generated by blasting, fall through the grate into the cabinet hopper. These particles are drawn into the reclaimer for separation. Dust and fines are first separated from the reusable blast media. Next the media is screened of oversize particles, and returned to the reclaimer hopper for reuse. Dust and fines are drawn from the reclaimer into the dust collector which traps the dust, discharging clean air. When the foot pedal is released the blasting stops.

We have brilliant logistics network owing to which safe and timely deliveries are guaranteed with us. Catering to the requirements of the customers; we are a renowned Supplier of Tack Rag Cloth.

Description :

• We are engaged in offering excellent quality Tack Cloth to our valuable clients.
• It is the professional choice for a perfect lint free finish. Use on metal or plastic surface.
• Compatible with latex alkyd, urethane, epoxy and varnish.

Direction :

• Remove cloth from bag. Use before each coat of paint or finish after normal preparation and blow off. Tack the surface using a soft gentle motion
• A gentle wiping action will pick up dust, dirt, lint and sand residue. Do not use on hot surfaces

Specifications :

• Package1 tack cloth, individually wrapped, 45 x 90 cm (18" x 36") cotton gauze 80% impregnated with petroleum resin 6.3 grams
• Colorwhite or brown

Features

• Reasonable price
• Tear resistant
• Different lengths

We are Dealing In STATFIELD EQUIPMENT, Pune make Coating & Liquid pianting Machine.Electrostatic Coating Equipment-90kv charging.30months Warranty & 98.5% GUARANTEED POWDER RECOVERY.

Serving the markets of Faridabad(India) and nearby area, we offer top-notch quality range. We are backed by a quality control wing that strictly check the lot at all stages right from the production to the final dispatch.

Construction :
Basically airless spraying system consists of a plunger pump, high pressure filter, a pressure hose and airless gun with nozzle. This is a very compact design and is easy to use.

Different Models In Airless :

• Sarita - Sarita is one of the models designed for maximum output fluid of 5 kg/min. It is a compact design which produces a maximum fluid pressure of 210 kgf /cm2 .The ratio is of 30:1 for this pump.
• Sagar - Sagar is a high end model for airless painting application. This model is available in a variety of range, producing fluid output of minimum of 150 kgf /cm2 to maximum of 500 kgf/ cm2. The maximum pressure ratio available with sagar is 75:1
• Airless Spray Gun - SAE - 5 - This Airless Spray Gun is a light weight and handy. It has proven its performance in varieties of application and therefore SAE-5 is known to be painter's first choice.

Salient Features :

• Paint path is internal & safe.
• For safety, trigger guard & Trigger lock are provided to avoid accidental spraying.
• To ensure longer life, cartridge type packing is provided.
• Extra fine mesh filter is provided inside the gun to avoid nozzle clogging.
• For maintenance, as easy access to fluid needle packing from outside.
• Swivel joint for ease of maneuverability.

Accessories :   

• T-C ( Turn Clean) Holder - It facilitates an instant flush-out of the clogged nozzle tip without removing the tip from the gun. This saves down time to a large extent.
• Extension Pipes - These can be attached to an airless gun to reach inaccessible & deep areas. Various lengths of pipes are available.   
• Free Pattern Tip - In this, the pattern width & fluid output can be easily adjusted and also, the clogged nozzle can be instantly flushed- just by rotating knob.
• Fluid Hose - Stainless steel & nylon on braided hoses with superior pulsation absorption capability & working pressure ranges up to 550 lg/cm2 are available for high pressure application.

Unbeatable Features of Gun :

• Internal paint path.
• Cartridge type packing.
• Trigger lock for safety.
• Extra fine mesh filter.

Airless Painting Equipments :

Statfield Equipments offers Airless Painting Equipments for high viscous coating and speedy painting, essential requirement for railway, shipping, construction and heavy machinery industries. Creative R&D, innovative approach, indigenized, sturdy designs, inbuilt efficiencies, cost- effective and prompt service are the hall mark that have kept Statfield in a leading position for the past decades.

Principle :
Paint is pressurized pneumatically under very high pressure with the help of double acting positive displacement ratio pump. This paint at high pressure is released into the atmosphere from the spray gun. The difference in the pressure causes atomization of the paint particles when released. The jet emerges as fine spray from the nozzle. The pumps depending on models and application develop pressure in between 90-480 Bar.

Airless equipment in comparison to conventional spray gun :

• Output of airless spray gun is 3 to 5 times faster as output is 100% paint compared 5% paint output in conventional gun.
• Paint attraction rate is about 10-20% more than conventional gun.
• Solvent/ Thinner saving is reduced by 20% as viscous paint can be handled by airless painting.

Why to use airless?

• For protective coating - heavy coating thickness is required.
• For heavy coating thickness- high viscous paint required.
• For viscous paints high pressure is required for the atomization.
• Very high pressure is not available with the conventional gun.
• Less bounce back thus, lower booth maintenance and cleanup time.
• There is Paint Saving Due to Minimum Bounce back in the airless.

Advantages of Airless :

• Viscous paints spraying at high pressure
• Less pollution
• Less bounce back
• Paint saving
• Saving in man hours
• Less bounce back thus, lower booth maintenance and cleanup time.
• Anti-corrosive coating on ship / off-shore platforms.
• Railways.
• Structural fabrication.
• Bridges.
• Dam gates.
• Automobiles.
• Transformers.
• Pipes.

We are engaged in offering fine quality Industrial Gas Burners to our valued clients across the world.  The product we are offering is generally used for coating or wrapping materials by applying the exact amount of heat. The product we supply is excellent in performance, as it is manufactured by using the high-quality material procured from the reliable vendors. While providing benefits like premium quality, durability, and customized design, we keep in mind the competitive nature of the market as well.

We are an eminent firm involved in the production of quality Batch Plant. Our entire assortment is manufactured by using the best quality raw material under the supervision of skilled technocrats, as per the international quality standards. Easy to install, these plants excel in performance and require low maintenance. We offer these plants to our esteemed customers in a spectrum of specifications and present them to our patrons at nominal prices. We cater to the bulk requirements of the clients.

Details : Optimization of energy, time, space, and finishing :

• Powder coating quality and efficiency can be optimized only if all the elements of complete powder coating process give optimized performance. Powder coating plants can be basically divided into conveyorised plants and batch plants. Batch plants are based on the premise that both the coating as well as curing process is optimized on the batch size.

• Besides the pretreatment, batch plant consists of applicators, recovery booth, curing oven and the material handling system.
• Statfield has proved its metal in the surface coating industry with its quality and technologically advance products. It is a one stop solution for the entire surface coating needs.
• We have successfully supplied powder coating and liquid painting batch plants to numerous industries. The variety in customization with cutting edge technology makes Statfield customers prime choice of all the batch plants in the market.

Why Statfield's Batch Plant?

• Statfield is itself a name for quality products.
• Four decades plus of expertise to prove ourselves on all grounds.
• Design being the crucial aspect of every plant, we have a full-fledged design department providing justification to each and every design.
• The only company to manufacture every product in-house enabling us to take total guarantee of the whole plant.
• The plants have very low running cost due to the quality material used.
• Wide network of dealers with well qualified service engineers provide round the clock service to the customers.

Construction :
The batch plant mainly comprises of the following :

• Painting Booth :
  
  • Powder coating : These types of booths consist of square chamber, multicyclone with blower, motor & bin. Each part of the booth is designed considering its importance in the system. The purpose of each component is different which should be considered from all angles.
  • Liquid painting : These types of booths are available in water wash & dry back type. In water wash type, there are two chambers separated by water curtain wall. The front spray chamber for painting & backside of water curtain wall is Suction Chamber to separate paint particles from air/thinner mixture. On the top of this chamber there is a Blower and Motor. In dry back type the water curtain is replaced with metallic filters. The dry type booth is recommended when paint consumption is less or water is scarce. Metallic filters are used for arresting the over sprayed paint and give clean air output to atmosphere.

• Curing Oven : Oven is made up of GI sheet. The construction is uniquely designed cassette type for optimum and uniform insulation. Rock wool up to 150 mm thicknesses is used for insulation purpose. Due to this construction there is optimum and uniform insulation. Extra corner angles are used for additional sturdiness.

• Material handling system : A batch plant material handling system comprises of over-head track and loose trolley or ground trolley. Track and trolley is used for lighter articles. For heavy articles load bar is suitable. Two trolleys can be joined for convenience. For still heavier articles ground trolleys are suitable.

The basic requirements are the same for powder coating and the liquid painting batch plant.

Working :
The working of the batch plant can be explained in the following steps -

• Step 1 : Pretreatment of articles : The articles to be powder coated or painted are needed to be clean from dust and grease. This is done through the 7s process in which the article is passed through containers of water and chemicals alternately and is cleansed.
• Step 2 : Article loading : The pretreated articles are bought to the painting / coating booth for painting with the help of the material handling equipments. The articles may be trolley mounted of hooked depending on the weight.
• Step 3 : Painting/Coating : The articles are coated / painted inside the booth manually or with the help of auto equipments like, the reciprocator. Then the articles are moved towards the oven through the sliding doors of the booth.
• Step 4 : Curing : The coated / painted articles are enclosed in the oven for curing at about 200 degree Celsius for 20 mins max. The cured article is then removed from the oven for further use.

The plants can be customized to the requirement of the customer and the dimension of the article.

Oven Selection : Generally electric fired ovens are selected for small batch size i.e. less heat load. For bigger batch size, oil fired or gas fired ovens are recommended. Heat exchanger gives advantage of indirect heating resulting in cleaner process and better curing quality.

Our range of products is favored by many, as it is quality guaranteed and according to global quality management standards. Based in Faridabad(India), our organization caters to the numerous requirements of the customers related to our products.

Our stringent quality procedures and analysis as per the guidelines help us in presenting reliable product range. Ours is a well-established organization that is located in Faridabad(India) and involved in catering to the customers based within and outside the boundaries.

Features :

• Robust light weight gun with operational safety.
• Both electrostatic & airless equipment mounted on single wheeled trolley.
• Saving due to wrap round effect.

Our firm is a trustworthy enterprise, offers excellent quality Electrostatic Liquid Painting Machine. Led by proficient engineers and the use of updated technologies, we are able to produce this Painting Machine. The products offered by us are in huge demand in the industry due to their sturdy construction and power packed performance. It has gained a huge appreciation in the market for its precise engineering, longer service life, and maintenance-free. We make this machine available at reasonable prices.

Details : In line with our philosophy, "Innovation to Perfection" we have introduced a new product in the liquid painting field. Persistent efforts and continuous R & D for many years have yielded the Charjet-Premium.

Charjet-Premium is the new age ELP machine with unending qualities. With an amazing saving, new failure diagnostic feature and with a host of other advantages, Charjet-Premium delivers a nearly failure proof experience.

The new Charjet ELP equipment comes in 2 models.

• Charjet Premium
• Charjet

• Saving is the most essential criteria of electrostatic equipment. Highest tip voltage given by us along with the improved soft atomization due to newly designed nozzle gives maximum saving & enhanced quality finish.

• The new equipment provides up to 40% more paint saving against any conventional gun and 10% to 20% against other ELP equipments in the market. It is equipped with Guaranteed Failure Free Cascade.

Automatic Applicator
Disc Applicator : This is used for painting of articles on conveyorised lines.

Working Principle : Pre - charged paint is fed to disc rotating at high speed, imparting centrifugal force. This causes atomization of paint. The paint particles are negatively charged gets deposited on the article due to Electrostatic effect. Transfer efficiency is very high and may reach 90%.

System Components :

• An electromechanical reciprocator with remotely controlled speed, stroke & zone control.
• Applicator.
• Paint feeding system.
• Paint charging unit.
• Control console.

Bell Applicator : This paint applicator can be used for painting large workpieces.

Working Principle :
The paint is fed to bell shaped applicator rotating at high speed (6000 rpm). The paint particles are atomized due to high rotation speed. The paint particles are negatively charged (at 100kV) and these follow the spray pattern generated due to the air shower and deposit on the article. Transfer efficiency is very high and may reach 90%.

System Components :

• An electromechanical reciprocator with remotely controlled speed, stroke & zone control.
• Bell applicator.
• Control console.

Teflon Coating

• Teflon has properties like non-stickiness, resistance to high temperature, resistance to weather and chemical reactions making it most suitable for industrial coatings. Due to its properties, Teflon paint is very costly forcing the user to maximize the paint use instead of Teflon.
• Electrostatic Liquid Painting Equipment can be suitably used for Teflon coating facilitating paint savings upto 15-20% leading to heavy cost savings. Liquid Teflon painting by Electrostatic applicator followed by application of Teflon powder is done on ball valves, cooking utensils, piping, irons etc.

Lacquer Coating

• Lacquering is done on aluminium and brass articles to give a fine film on the articles retaining the original luster of the metals plus giving a smooth finish. For the lacquer coating application, set of Electrostatic Spray applicator, Transfer pump and Stirrer is used.
• Lacquer savings of 25-30% can be established due to use of Electrostatic Lacquer applicator. Because of the electrostatic field generated, maximum lacquer gets deposited on the article hence there is less overspray and less bounce back. Due to the fine atomization of lacquer particles, there is better distribution of particles on the article. Hence high Lacquer savings can be established as compared to the conventional gun.

We are one of the most esteemed company in the industry, engaged in offering Paint Transfer Pumps. These are constructed and engineered by skillful technicians by using the top grade raw materials & components as per industry standards. These pumps are used in the paint spraying system especially in various automobile workshops for ensuring uninterrupted, uniform and filtered paint feeding to the spraying gun. These are available at the most affordable market prices.

Details : Prapat, the paint transfer pump in the paint spraying system is used for ensuring uninterrupted, uniform and filtered paint feeding to the spraying gun. The pneumatically operated piston type pump is a compact and sophisticated option to the conventional pressure feed container. Prapat provides uniform and easily controlled delivery. The easy to monitor, sleek design and light weight ensures great reduction of paint wastage in the painting process.

Advantages : Uninterrupted paint feeding. Quick and easy colour change. Lower rejects as paint is uncontaminated. Savings in paint due to minimum wastages while cleaning/ colour change operations.

Paint Stirrer

• Many paints have settling property due to which solid particles accumulate at the bottom over a period of time. Hence, this deters the paint quality & finish. So, continuous stirring is required. Statfield offer Pneumatic stirrers for this purpose.
• Stirrers can be offered along with different capacity S.S. containers and with isolation for metallic paint for electrostatic operation.

Available in two models :

• Model ST I - For general viscosity paints.
• Model ST II - For medium and high viscosity paints.

With the support of our qualified workforce, we have been committed to offering strongly built Powder Coating Machine to our clients. This equipment is designed with the latest technology and fulfilled all the set parameters in the market. The provided coating machine is mainly used to coat metals and serve various industries like automobile and printing. These machines are strong and sturdy in nature and have a long service life. Our offered range is available as per the modern trend and is provided at market leading prices.

Details :

• In Touch with Technology!!! Statfield Equipments Pvt. Ltd., has been proudly wearing the crown of "Pioneer" since the eighties. Statfield has given 'ever-updated' advanced equipments to the market with the twin Philosophy of Innovation and Customer satisfaction.

• With expertise gained over decades, Statfield has invented various elements of the powder coating process to achieve customer satisfaction through the Science of Powder management. Be it the high transfer efficiency of the Shalaka Series Guns or the High Recovery Efficiency of the Multi Cyclones. Statfield has been continuously upgrading this Powder Management Science.

• Over the years, Statfield has added automatic applicators, recycling system and post filter to tie up all loose ends in Powder Management. To give justice to Statfield Innovative Technologies, we have and will keep on perfecting the Science of Powder Management.

Maxim :

• Powder Coating World is in new scenario of quality and rates, as rates are going down and customers are demanding more. To balance such a situation is a new challenge for manufacturer, thus the manufacturer has to minimize the production cost by optimum use of machinery and man power.

• "Stafield" has discovered a super techno model of powder coating which minimizes operating cost of powder coating unit and saves time.

Standard Features :

• Shalaka 17 : The new age powder coating gun is based on concept of low energy generation. A unique device providing safety with enriched powder charging and uniform powder flow. It is lightweight & well balanced due to its molded parts of modern polymer.
  
  • It gives safety with enriched powder charging.
  • The unique external path leads to uniform powder flow.
  • This gun is lightweight & well balanced due to its moulded parts of modern polymer.
  • Now you can spray metallic powder without changing Nozzle.
  • Reduced spares consumption.

• Fold back characteristic : The gun operates at maximum efficiency having tip voltage of 80-90 Kv at a distance of 150 mm from article. While coating the cavities when the gun is moved nearer to article the voltage and current reduce thus, charge at the edges of cavity decreases and powder penetrates the cavity and if the gun accidentally touches the article, human body, current automatically reduces to zero.

• Moving cap : It makes the powder beam narrow or broad, just with a slide.
• External powder path :Its easy to clean during color change.
• Suitability for metallic powder : No need of separate nozzle for metallic powder application.
• Touch Trigger : A very special feature in which gun triggers just by touching the metal piece. There is no moving mechanism at all. So failures are avoided. The supply is not earthed gun doesn't trigger.
• Control block : It's a newly designed powder pump for smooth & uniform flow with high volume powder output & less air consumption avoiding bounce back problem.
• Powder hopper : It's made up of SS, round and smooth with no welding joints or corners, and has three piece construction. This reduces the color change time.
• Light weight : The gun is manufactured from specialized polymers material which is light in weight enhancing durability and reduces labor fatigue.
• Ergonomically designed : The Ergonomically designed gun is well balanced increasing flexibility and reducing stress on a particular angle.
• No frequent Breakdowns :The cascade inside and external powder path makes the gun failure free.
• Optional Attachments : Variety of spray heads are developed to improve coating results for specific articles. Flat nozzle for plane articles, Star or plus nozzle for cavity coating, extension nozzle for deep areas are preferred generally.
• Minicon : A very small 0.8 kg container can be used for trials.

Unique Features of Maxim :

• Built in sieve : Provides an automatic sieving for the recycled as well as fresh powder, saving labor.
• Vibratory trolley : The vibrating trolley assists sieving action.
• Optional control for sieving: The switch can help to choose in between manual and auto sieving.
• Powder level sensor : The sensor gives an audio visual alarm for minimum level of powder in the hopper.

Other Models : Magnum I, Magnum II, Magnum BM : All these models have common standard features of Maxim which is our core technology. Selection depends upon different facilities like sieve, hopper capacities etc.

We are amongst the eminent names in the industry, engaged in offering a complete range of Laboratory Testing Equipment. This range is manufactured by using the quality tested raw materials under the supervision of our highly skilled professionals. Used in laboratories for testing and experimentation purposes, our equipment has been acknowledged for its great performance, long service life, and accuracy. Our offered product can be availed at the industrial leading prices.

Owing to the vast experience and state-of-the-art infrastructure we are instrumental in providing a wide array of Powder Management System. The system offered by us is manufactured our experts using quality checked components and advanced technology in compliance with set industry norms. Moreover, our offered range can be availed in a wide range of specifications, as per the requirements of our esteemed clients.  We provide this system at market leading prices within promised time frame.

System : The powder collected in the recovery bins of Multicyclone is fed to recycled powder hopper through a sieve. The fresh powder is stored in a separate fresh powder hopper. Powder from both these hoppers is fed to the second sifter assembly through ejector pump and minicyclone. Here the powders gets well mixed and then gets collected in the mixed powder hopper. This hopper will feed powder to the applicators. As recovered and fresh powder is sieved again, total coating quality is improved.

Proportionate Mixing :

• The mixing of powder can be done proportionately either manually or automatically. In the manual system, each ejector pump will have separate powder control, which can be set manually to the desired mixing ratio. In the automatic system, the operator is required to feed only desired mixing ratio say 80 : 20 or 70 : 30.
• Due to continuous powder loop formation manual handling is avoided and consistent powder supply is achieved with improvement in quality.

Post Filter

• 98.5% efficiency of the Multicyclone helps in maximum utilization of chargeable powder. But to comply with Pollution Control Laws, the 1.5% powder fines are required to be arrested. The post filter arrests this powder and gives out breathable air.
• A number of filter cartridges are mounted inside the sealed metallic chamber. The air enters the chamber and the filteration occurs 'outside in'. Periodic purge removes the powder and clean the cartridge. Clean air is given out through the blower outlet.

Integration ConceptBooth - when integrated with Equipment and post filter gives :

• Automatic mixing of fresh & recovered powder.
• Automatic feeding of powder to spray gun.
• Automatic on-line sieving.
• Prevention of entry of fines in atmosphere.

Recycling system : The recycling system helps in optimum utilization of powder. Powder is recycled automatically back to the gun through the sieving machine.

Sieving Machine Sifter : This high sieving rate machine can accommodate powder flow from three Multi Cyclones. The sieves are available in variety of sizes catering to different powders. Sufficient dampening provides noiseless operation.

Technical Specifications :

• Standard Mesh - 60
• Optional Mesh - 80, 100

Ejector Pump :This high volume capacity pump sucks powder from the multi cyclone recovery bins delivering it to the sieve chamber through the mini cyclone.

Technical Specifications : Standard Mesh - 60

Hopper : Carbon Steel Powder containers with provision for fluidization are used as reservoir to supply powder to spray applicators.

Technical Specifications :

• Standard Sizes : 20 kg, 40 kg, 80 kg, 120 kg.

Mini Cyclone ;Mini Cyclone feeds powder to the sieve and then to the hopper. During the process, fines get separated and delivered back to the powder booth to avoid air pollution.

Being an established brand in the industry we are offering Sand Blasting Machine to our valued clients. The product we offer is excellent in quality, as it is manufactured by using the excellent quality materials along with the latest technology. The product is designed for precision and excellence by our experienced team of professionals.  Our product is highly demanded, as it is used for various applications like cleaning of molds, putting grains on the molds, preparing the surface for painting, coating, and much more. We are offering this machine at a very marketable rate.

Portable Abrasive Blaster

• The portable abrasive blaster are safe, high productivity systems designed for use with a wide range of abrasive media. The operation is performed on metals, glass, ceramics, plastic and stone.
• The machine works on pressure blasting principle, consist of a blast generator. The abrasives are filled at the top of machine when machine is not working and blast generator is not pressurized. At the top, a vibrating sieve is provided to sieve the abrasive filled. The oversize abrasive and debris are retained on the screen, thus prevent the choking of blast line. When mushroom valve is opened the abrasive will get transferred to blast generator for blasting. The mushroom valve gets closed when compressed air is switched on and abrasive storage tank gets pressurized, for free fall of abrasive into the mixing tube. From mixing tube the abrasive is carried away by compressed air to the nozzle for blasting. The Blast Generator is fabricated from MS Steel plate of thickness not less than 6 mm as per IS-2825 and hydraulically tested for 250 psi.

Our vision to be known as the best in the market has enabled us to offer and excellent quality Shot Blasting Machine to our valued customers. We manufacture this product keeping in mind the needs and demands of the customers. The product we are offering is excellent in quality and well designed. The offered product is used in various industries for the purpose of cleaning or preparing a surface. We are offering this product at a very marketable rate.

Details : About Blast Cabinet Blast Cabinet is an enclosure which houses the abrasive propelling mechanism (blast gun), holds work in position and confines flying abrasive particles and dust. Features of Blast Cabinets Machine meets ISO Standards All cabinet models are rubber lined inside large vision window. vision glass is protected by a wire screen against abrasion and glass is easily replaceable. Easy fitting of accessories like nozzles, hoses etc. Whenever required at site. New ergonomic cabinet is designed to snake operator relaxed while working. Blasting start/stop is through foot valve so that both hands of operator are free to maneuver the job or blasting nozzle. Air pressure gauge, air pressure regulator, moisture separator (except Wet Blaster) and an air gun is provided as standard fitting. Simple operation and simple installation as the machines are ready to operate when connected with airline and electric supply. foundation or pit for installation not necessary. fabricated from heavy gauge mild steel, folded and welded construction. It incorporate sealed hand holes ans gasketed doors to ensure that dust will not escape outside. Environmentally clean and friendly as dust collection device is attached so only clean air is 1 discharged to atmosphere. Noise level of fan is kept below 80 dBA at operators position. proper ventilation is provided for clear visibility while blasting. Doors are provided with cam lock system, which seals the door across the width by operating a single lever, and are easy to open / close. High lums transfer good illumination also proper ventilation for clear visibility.

Suction BlasterSuction Blaster is the simplest and most effective way to remove corrosion and old paint. Suction Blaster is a clean, dust free sand blaster that leaves the surface cleaned and well prepared for painting, filling etc. When the cabinet and power module are correctly set-up, the cabinet is ready for operation by actuation of the foot pedal. Fully depressing the foot pedal causes air to flow through the blast gun. Air moving through the gun draws media into the blast gun mixing chamber. The media mixes with the air and is propelled out the nozzle. After striking the object being blasted, the blast media, along with fines, dust, and byproducts generated by blasting, fall through the grate into the cabinet hopper. These particles are drawn into the reclaimer for separation. Dust and fines are first separated from the reusable blast media. Next the media is screened of oversize particles, and returned to the reclaimer hopper for reuse. Dust and fines are drawn from the reclaimer into the dust collector which traps the dust, discharging clean air. When the foot pedal is released the blasting stops.

We have brilliant logistics network owing to which safe and timely deliveries are guaranteed with us. Catering to the requirements of the customers; we are a renowned Supplier of Tack Rag Cloth.

Description :

• We are engaged in offering excellent quality Tack Cloth to our valuable clients.
• It is the professional choice for a perfect lint free finish. Use on metal or plastic surface.
• Compatible with latex alkyd, urethane, epoxy and varnish.

Direction :

• Remove cloth from bag. Use before each coat of paint or finish after normal preparation and blow off. Tack the surface using a soft gentle motion
• A gentle wiping action will pick up dust, dirt, lint and sand residue. Do not use on hot surfaces

Specifications :

• Package1 tack cloth, individually wrapped, 45 x 90 cm (18" x 36") cotton gauze 80% impregnated with petroleum resin 6.3 grams
• Colorwhite or brown

Features

• Reasonable price
• Tear resistant
• Different lengths

We are Dealing In STATFIELD EQUIPMENT, Pune make Coating & Liquid pianting Machine.Electrostatic Coating Equipment-90kv charging.30months Warranty & 98.5% GUARANTEED POWDER RECOVERY.

Serving the markets of Faridabad(India) and nearby area, we offer top-notch quality range. We are backed by a quality control wing that strictly check the lot at all stages right from the production to the final dispatch.

Construction :Basically airless spraying system consists of a plunger pump, high pressure filter, a pressure hose and airless gun with nozzle. This is a very compact design and is easy to use.

Different Models In Airless :

• Sarita - Sarita is one of the models designed for maximum output fluid of 5 kg/min. It is a compact design which produces a maximum fluid pressure of 210 kgf /cm2 .The ratio is of 30:1 for this pump.
• Sagar - Sagar is a high end model for airless painting application. This model is available in a variety of range, producing fluid output of minimum of 150 kgf /cm2 to maximum of 500 kgf/ cm2. The maximum pressure ratio available with sagar is 75:1
• Airless Spray Gun - SAE - 5 - This Airless Spray Gun is a light weight and handy. It has proven its performance in varieties of application and therefore SAE-5 is known to be painter's first choice.

Salient Features :

• Paint path is internal & safe.
• For safety, trigger guard & Trigger lock are provided to avoid accidental spraying.
• To ensure longer life, cartridge type packing is provided.
• Extra fine mesh filter is provided inside the gun to avoid nozzle clogging.
• For maintenance, as easy access to fluid needle packing from outside.
• Swivel joint for ease of maneuverability.

Accessories :   

• T-C ( Turn Clean) Holder - It facilitates an instant flush-out of the clogged nozzle tip without removing the tip from the gun. This saves down time to a large extent.
• Extension Pipes - These can be attached to an airless gun to reach inaccessible & deep areas. Various lengths of pipes are available.   
• Free Pattern Tip - In this, the pattern width & fluid output can be easily adjusted and also, the clogged nozzle can be instantly flushed- just by rotating knob.
• Fluid Hose - Stainless steel & nylon on braided hoses with superior pulsation absorption capability & working pressure ranges up to 550 lg/cm2 are available for high pressure application.

Unbeatable Features of Gun :

• Internal paint path.
• Cartridge type packing.
• Trigger lock for safety.
• Extra fine mesh filter.

Airless Painting Equipments :

Statfield Equipments offers Airless Painting Equipments for high viscous coating and speedy painting, essential requirement for railway, shipping, construction and heavy machinery industries. Creative R&D, innovative approach, indigenized, sturdy designs, inbuilt efficiencies, cost- effective and prompt service are the hall mark that have kept Statfield in a leading position for the past decades.

Principle :Paint is pressurized pneumatically under very high pressure with the help of double acting positive displacement ratio pump. This paint at high pressure is released into the atmosphere from the spray gun. The difference in the pressure causes atomization of the paint particles when released. The jet emerges as fine spray from the nozzle. The pumps depending on models and application develop pressure in between 90-480 Bar.

Airless equipment in comparison to conventional spray gun :

• Output of airless spray gun is 3 to 5 times faster as output is 100% paint compared 5% paint output in conventional gun.
• Paint attraction rate is about 10-20% more than conventional gun.
• Solvent/ Thinner saving is reduced by 20% as viscous paint can be handled by airless painting.

Why to use airless?

• For protective coating - heavy coating thickness is required.
• For heavy coating thickness- high viscous paint required.
• For viscous paints high pressure is required for the atomization.
• Very high pressure is not available with the conventional gun.
• Less bounce back thus, lower booth maintenance and cleanup time.
• There is Paint Saving Due to Minimum Bounce back in the airless.

Advantages of Airless :

• Viscous paints spraying at high pressure
• Less pollution
• Less bounce back
• Paint saving
• Saving in man hours
• Less bounce back thus, lower booth maintenance and cleanup time.
• Anti-corrosive coating on ship / off-shore platforms.
• Railways.
• Structural fabrication.
• Bridges.
• Dam gates.
• Automobiles.
• Transformers.
• Pipes.

We are engaged in offering fine quality Industrial Gas Burners to our valued clients across the world.  The product we are offering is generally used for coating or wrapping materials by applying the exact amount of heat. The product we supply is excellent in performance, as it is manufactured by using the high-quality material procured from the reliable vendors. While providing benefits like premium quality, durability, and customized design, we keep in mind the competitive nature of the market as well.

We are an eminent firm involved in the production of quality Batch Plant. Our entire assortment is manufactured by using the best quality raw material under the supervision of skilled technocrats, as per the international quality standards. Easy to install, these plants excel in performance and require low maintenance. We offer these plants to our esteemed customers in a spectrum of specifications and present them to our patrons at nominal prices. We cater to the bulk requirements of the clients.

Details : Optimization of energy, time, space, and finishing :

• Powder coating quality and efficiency can be optimized only if all the elements of complete powder coating process give optimized performance. Powder coating plants can be basically divided into conveyorised plants and batch plants. Batch plants are based on the premise that both the coating as well as curing process is optimized on the batch size.

• Besides the pretreatment, batch plant consists of applicators, recovery booth, curing oven and the material handling system.
• Statfield has proved its metal in the surface coating industry with its quality and technologically advance products. It is a one stop solution for the entire surface coating needs.
• We have successfully supplied powder coating and liquid painting batch plants to numerous industries. The variety in customization with cutting edge technology makes Statfield customers prime choice of all the batch plants in the market.

Why Statfield's Batch Plant?

• Statfield is itself a name for quality products.
• Four decades plus of expertise to prove ourselves on all grounds.
• Design being the crucial aspect of every plant, we have a full-fledged design department providing justification to each and every design.
• The only company to manufacture every product in-house enabling us to take total guarantee of the whole plant.
• The plants have very low running cost due to the quality material used.
• Wide network of dealers with well qualified service engineers provide round the clock service to the customers.

Construction :The batch plant mainly comprises of the following :

• Painting Booth :
  • Powder coating : These types of booths consist of square chamber, multicyclone with blower, motor & bin. Each part of the booth is designed considering its importance in the system. The purpose of each component is different which should be considered from all angles.
  • Liquid painting : These types of booths are available in water wash & dry back type. In water wash type, there are two chambers separated by water curtain wall. The front spray chamber for painting & backside of water curtain wall is Suction Chamber to separate paint particles from air/thinner mixture. On the top of this chamber there is a Blower and Motor. In dry back type the water curtain is replaced with metallic filters. The dry type booth is recommended when paint consumption is less or water is scarce. Metallic filters are used for arresting the over sprayed paint and give clean air output to atmosphere.

• Curing Oven : Oven is made up of GI sheet. The construction is uniquely designed cassette type for optimum and uniform insulation. Rock wool up to 150 mm thicknesses is used for insulation purpose. Due to this construction there is optimum and uniform insulation. Extra corner angles are used for additional sturdiness.

• Material handling system : A batch plant material handling system comprises of over-head track and loose trolley or ground trolley. Track and trolley is used for lighter articles. For heavy articles load bar is suitable. Two trolleys can be joined for convenience. For still heavier articles ground trolleys are suitable.

The basic requirements are the same for powder coating and the liquid painting batch plant.

Working :The working of the batch plant can be explained in the following steps -

• Step 1 : Pretreatment of articles : The articles to be powder coated or painted are needed to be clean from dust and grease. This is done through the 7s process in which the article is passed through containers of water and chemicals alternately and is cleansed.
• Step 2 : Article loading : The pretreated articles are bought to the painting / coating booth for painting with the help of the material handling equipments. The articles may be trolley mounted of hooked depending on the weight.
• Step 3 : Painting/Coating : The articles are coated / painted inside the booth manually or with the help of auto equipments like, the reciprocator. Then the articles are moved towards the oven through the sliding doors of the booth.
• Step 4 : Curing : The coated / painted articles are enclosed in the oven for curing at about 200 degree Celsius for 20 mins max. The cured article is then removed from the oven for further use.

The plants can be customized to the requirement of the customer and the dimension of the article.

Oven Selection : Generally electric fired ovens are selected for small batch size i.e. less heat load. For bigger batch size, oil fired or gas fired ovens are recommended. Heat exchanger gives advantage of indirect heating resulting in cleaner process and better curing quality.

Our range of products is favored by many, as it is quality guaranteed and according to global quality management standards. Based in Faridabad(India), our organization caters to the numerous requirements of the customers related to our products.

Our stringent quality procedures and analysis as per the guidelines help us in presenting reliable product range. Ours is a well-established organization that is located in Faridabad(India) and involved in catering to the customers based within and outside the boundaries.

Features :

• Robust light weight gun with operational safety.
• Both electrostatic & airless equipment mounted on single wheeled trolley.
• Saving due to wrap round effect.

Our firm is a trustworthy enterprise, offers excellent quality Electrostatic Liquid Painting Machine. Led by proficient engineers and the use of updated technologies, we are able to produce this Painting Machine. The products offered by us are in huge demand in the industry due to their sturdy construction and power packed performance. It has gained a huge appreciation in the market for its precise engineering, longer service life, and maintenance-free. We make this machine available at reasonable prices.

Details : In line with our philosophy, "Innovation to Perfection" we have introduced a new product in the liquid painting field. Persistent efforts and continuous R & D for many years have yielded the Charjet-Premium.
Charjet-Premium is the new age ELP machine with unending qualities. With an amazing saving, new failure diagnostic feature and with a host of other advantages, Charjet-Premium delivers a nearly failure proof experience.

The new Charjet ELP equipment comes in 2 models.

• Charjet Premium
• Charjet

• Saving is the most essential criteria of electrostatic equipment. Highest tip voltage given by us along with the improved soft atomization due to newly designed nozzle gives maximum saving & enhanced quality finish.

• The new equipment provides up to 40% more paint saving against any conventional gun and 10% to 20% against other ELP equipments in the market. It is equipped with Guaranteed Failure Free Cascade.

Automatic Applicator
Disc Applicator : This is used for painting of articles on conveyorised lines.

Working Principle : Pre - charged paint is fed to disc rotating at high speed, imparting centrifugal force. This causes atomization of paint. The paint particles are negatively charged gets deposited on the article due to Electrostatic effect. Transfer efficiency is very high and may reach 90%.

System Components :

• An electromechanical reciprocator with remotely controlled speed, stroke & zone control.
• Applicator.
• Paint feeding system.
• Paint charging unit.
• Control console.

Bell Applicator : This paint applicator can be used for painting large workpieces.

Working Principle :The paint is fed to bell shaped applicator rotating at high speed (6000 rpm). The paint particles are atomized due to high rotation speed. The paint particles are negatively charged (at 100kV) and these follow the spray pattern generated due to the air shower and deposit on the article. Transfer efficiency is very high and may reach 90%.

System Components :

• An electromechanical reciprocator with remotely controlled speed, stroke & zone control.
• Bell applicator.
• Control console.

Teflon Coating

• Teflon has properties like non-stickiness, resistance to high temperature, resistance to weather and chemical reactions making it most suitable for industrial coatings. Due to its properties, Teflon paint is very costly forcing the user to maximize the paint use instead of Teflon.
• Electrostatic Liquid Painting Equipment can be suitably used for Teflon coating facilitating paint savings upto 15-20% leading to heavy cost savings. Liquid Teflon painting by Electrostatic applicator followed by application of Teflon powder is done on ball valves, cooking utensils, piping, irons etc.

Lacquer Coating

• Lacquering is done on aluminium and brass articles to give a fine film on the articles retaining the original luster of the metals plus giving a smooth finish. For the lacquer coating application, set of Electrostatic Spray applicator, Transfer pump and Stirrer is used.
• Lacquer savings of 25-30% can be established due to use of Electrostatic Lacquer applicator. Because of the electrostatic field generated, maximum lacquer gets deposited on the article hence there is less overspray and less bounce back. Due to the fine atomization of lacquer particles, there is better distribution of particles on the article. Hence high Lacquer savings can be established as compared to the conventional gun.

We are one of the most esteemed company in the industry, engaged in offering Paint Transfer Pumps. These are constructed and engineered by skillful technicians by using the top grade raw materials & components as per industry standards. These pumps are used in the paint spraying system especially in various automobile workshops for ensuring uninterrupted, uniform and filtered paint feeding to the spraying gun. These are available at the most affordable market prices.

Details : Prapat, the paint transfer pump in the paint spraying system is used for ensuring uninterrupted, uniform and filtered paint feeding to the spraying gun. The pneumatically operated piston type pump is a compact and sophisticated option to the conventional pressure feed container. Prapat provides uniform and easily controlled delivery. The easy to monitor, sleek design and light weight ensures great reduction of paint wastage in the painting process.

Advantages : Uninterrupted paint feeding. Quick and easy colour change. Lower rejects as paint is uncontaminated. Savings in paint due to minimum wastages while cleaning/ colour change operations.

Paint Stirrer

• Many paints have settling property due to which solid particles accumulate at the bottom over a period of time. Hence, this deters the paint quality & finish. So, continuous stirring is required. Statfield offer Pneumatic stirrers for this purpose.
• Stirrers can be offered along with different capacity S.S. containers and with isolation for metallic paint for electrostatic operation.

Available in two models :

• Model ST I - For general viscosity paints.
• Model ST II - For medium and high viscosity paints.

With the support of our qualified workforce, we have been committed to offering strongly built Powder Coating Machine to our clients. This equipment is designed with the latest technology and fulfilled all the set parameters in the market. The provided coating machine is mainly used to coat metals and serve various industries like automobile and printing. These machines are strong and sturdy in nature and have a long service life. Our offered range is available as per the modern trend and is provided at market leading prices.

Details :

• In Touch with Technology!!! Statfield Equipments Pvt. Ltd., has been proudly wearing the crown of "Pioneer" since the eighties. Statfield has given 'ever-updated' advanced equipments to the market with the twin Philosophy of Innovation and Customer satisfaction.

• With expertise gained over decades, Statfield has invented various elements of the powder coating process to achieve customer satisfaction through the Science of Powder management. Be it the high transfer efficiency of the Shalaka Series Guns or the High Recovery Efficiency of the Multi Cyclones. Statfield has been continuously upgrading this Powder Management Science.

• Over the years, Statfield has added automatic applicators, recycling system and post filter to tie up all loose ends in Powder Management. To give justice to Statfield Innovative Technologies, we have and will keep on perfecting the Science of Powder Management.

Maxim :

• Powder Coating World is in new scenario of quality and rates, as rates are going down and customers are demanding more. To balance such a situation is a new challenge for manufacturer, thus the manufacturer has to minimize the production cost by optimum use of machinery and man power.

• "Stafield" has discovered a super techno model of powder coating which minimizes operating cost of powder coating unit and saves time.

Standard Features :

• Shalaka 17 : The new age powder coating gun is based on concept of low energy generation. A unique device providing safety with enriched powder charging and uniform powder flow. It is lightweight & well balanced due to its molded parts of modern polymer.
  • It gives safety with enriched powder charging.
  • The unique external path leads to uniform powder flow.
  • This gun is lightweight & well balanced due to its moulded parts of modern polymer.
  • Now you can spray metallic powder without changing Nozzle.
  • Reduced spares consumption.

• Fold back characteristic : The gun operates at maximum efficiency having tip voltage of 80-90 Kv at a distance of 150 mm from article. While coating the cavities when the gun is moved nearer to article the voltage and current reduce thus, charge at the edges of cavity decreases and powder penetrates the cavity and if the gun accidentally touches the article, human body, current automatically reduces to zero.

• Moving cap : It makes the powder beam narrow or broad, just with a slide.
• External powder path :Its easy to clean during color change.
• Suitability for metallic powder : No need of separate nozzle for metallic powder application.
• Touch Trigger : A very special feature in which gun triggers just by touching the metal piece. There is no moving mechanism at all. So failures are avoided. The supply is not earthed gun doesn't trigger.
• Control block : It's a newly designed powder pump for smooth & uniform flow with high volume powder output & less air consumption avoiding bounce back problem.
• Powder hopper : It's made up of SS, round and smooth with no welding joints or corners, and has three piece construction. This reduces the color change time.
• Light weight : The gun is manufactured from specialized polymers material which is light in weight enhancing durability and reduces labor fatigue.
• Ergonomically designed : The Ergonomically designed gun is well balanced increasing flexibility and reducing stress on a particular angle.
• No frequent Breakdowns :The cascade inside and external powder path makes the gun failure free.
• Optional Attachments : Variety of spray heads are developed to improve coating results for specific articles. Flat nozzle for plane articles, Star or plus nozzle for cavity coating, extension nozzle for deep areas are preferred generally.
• Minicon : A very small 0.8 kg container can be used for trials.

Unique Features of Maxim :

• Built in sieve : Provides an automatic sieving for the recycled as well as fresh powder, saving labor.
• Vibratory trolley : The vibrating trolley assists sieving action.
• Optional control for sieving: The switch can help to choose in between manual and auto sieving.
• Powder level sensor : The sensor gives an audio visual alarm for minimum level of powder in the hopper.

Other Models : Magnum I, Magnum II, Magnum BM : All these models have common standard features of Maxim which is our core technology. Selection depends upon different facilities like sieve, hopper capacities etc.