Book Spine Pre-Gluer equipped with Hot Air IR Dryer, is the most economical system for preparation of Book-Blocks suitable for Soft or Hard Case Binding by pre-gluing and drying of section-sewn, pre-smashed and nipped signatures. The process ensures that the Book-Blocks maintain its rectangular shape, which is free from extreme gradients in the folded sewn area. The section - sewn signatures Book-blocks are held under set pressure with spine resting on the flat surface to ensure rightangle reference of the spine in relation to the height of the book. The books upto a maximum pile size of 710mm can be processed at a time with pile under hydraulic pressure ranging from 1000- 1500kgs. The pile is hydraulically raised for turning the same to 180 with Spine-section exposed. Apply Glue with the help of a brush or sponge, a very thin layer of GlueAdhesive (preferably flexible, non-swelling Synthetic such as polyvinyl or AnimalJelly Glue etc. is recommended). Ensure that the amount of Glue applied to the Spine should be just adequate to sufficiently seal the adjoining signatures. The Dryer Unit equipped with Quartz IR Heaters and High Speed fans is brought over the Book Spine Area by sliding the Unit towards operating side. The Adhesive is dried within 2-3 minutes. The Dryer Unit is pushed back to its reset position on completion of the set-time. Book Spine Pre-Gluer Press is a neat cuboid of a machine sturdily built for processing Book-blocks economically with space power saving and simple to operate for consistent quality.

Ideal round cornering machine for rounding of catalogues; books; exercise note books; diaries and other stationery articles etc. Heavy duty hydraulic twin corner cutting press can be fitted with different tools (dies) with radius ranging from r-3 to r-14 mm. Each set of cutting tools consist of two parts: an upper blade to be fitted to the moving platen and the lower die to be fitted in a special slot on the working platform. Chute is provided for shavingscutting waste to be collected in a binbag which can be attached (by the user) to the frame. Twin corner cutting press (tcc) is equipped with two cutting heads to cut both the corners simultaneously. The distance (inoutward) of both the cutting tools can be set with respective hand-wheels attached to the towers. The holding and pre-pressing operation is carried out by a built-in device and on completion of the cycle, both the holding and mechanism return to reset position. Control panel conveniently located. Foot switch is provided for ease in handling the material being processed. Emergency switch is provided for aborting the cycle midway. Castor provided for maximum mobility.

Pressing of cased-in books and simultaneous burning-in of the JOINTS for forming perfect hinge and permanent shape with the help of temperature-controlled pressure blades (Joint Forming Bars) for Flat or Rounded Spine of Book-Blocks. These blades are spring loaded for adjusting to different depth of joints automatically and hydraulic pressure can be set from 100-300400kgs to achieve the desired results. The bars (Joint Formers) are supplied for Flat and Rounded Spine Book-backs respectively. Temperature of the Joint Formers is set through Digital Temperature Controller (PID) to suit properties of Glue (Adhesive), Binding material and operating speed. The PLC (Programmable Logic Controller) enables choice of single or multiple strokes for accurate control of burning-in the Joints and consistent results. Counter on PLC indicates number of books processed at the end of each cycle. The system automatically releases the book on completion of the set timing cycle. Back-gauge (setting handle mounted on the front panel) is provided for faster make-ready production; Light Guide indicates the Joint Forming position and also reduces the make-ready time. Specially designed operator Safety Device in addition to Emergency Switch incorporated. Provision for Joint Forming of foam padded cases available. PLC based control panel for optimum reliability and simplified diagnostics. Press equipped with Castors for maximum space saving utilisation.

Hydraulic Book Press designed specially for Exercise Note Booksstationery Manufacturers. The platen area adequately covers 3-Up or 4-Up Exercise Note Books. The printed title can be pasted on open book-size upto 800x500mm 1040x650mm with daylight area upto 260mm on both upper & lower decks-alternatively Moving on both the sides and the Upper & Lower Fixed Base Platen are equipped with stainless steel plates for best results. Centrally positioned Moving Platen is convenient for utilizing maximum idle time. While the lower deck is being used for pressing the stack of books etc, the upper deck can be loaded for next cycle. Timer can be set to meet specific requirement of boards cards sheets. The system would release the stack of book from either upper lower deck after a pre-set time. Thereby ensuring all books are pressed uniformly . Control Panel is equipped with Mains Switch; Pump ONOFF Switch; Switch for operating the system in Manual Mode; Timer (0-999 seconds) Manual Auto Mode Switch and Emergency Switch. Castors are provided for maximum space utilisation.

Table Top Glue Applicator for een spread of adhesive at a considerable saving of conumption upto 40% approximately. Suitable for PVA, Cold Glues in general and Hot Animal Glue upto 60oC to 70oC. Glue heating by radition through a thermostat control. Glue control through micrometeric scraper roller. Paper, Cloth, Buckrum & PVC etc upto 400gsm or 1mm thick meterial can be glued. Variable Speed drive enable wide range of materials to be processed. Manual feeding and rollers(adjustable) to cater to different gauge of materials. Stripper fingers assist in lifting the glued material.

Ideally suited for pressing and bundling of folded sheets (signatures), brochures, book- blocks etc. For perfect and hard-case binding process. The hydraulically pressed bundles preserve the freshcrisp look of the print as it prevents air & dust from spoiling the folded sheets(signatures). It protects the edges and facilitates stacking & storing of the bundles (pre post gathering collating) for optimum utilization of space. Push-buttonfoot-switch operated hydraulic system has a built-in power saving device. When the push button or foot-switch is activated, the motor automatically gets switched-on. The motor also gets switched-off as soon as the pre-set pressure (adjustable upto 2000kgs) is attained. Reset push button for release of the bundle and the moving platen returns to its set-open position. Groovesslots provided on pressure plates of fixed & moving platens for guiding the tape(strapbelt) cord(string) and prevent it from getting entangled with the pile of signatures. Tray provided on moving platen for storing excess length of cord tape strap and for placing the end support planks (plyboard hardboard). Clip on the left hand side of the fixed platen provided for holding one end of the tape (strap) cord (string). Motor remains switched off during idle period, the same comes on when any of the function i.e. Forward reset of the moving platen is activated. This is a power saving feature. Control panel is located for maximum operator convenience. Castors provided for maximum space utilisation & mobility.