Our Products
MODEL TCS-40 Chiller Tube Cleaning Systemis the most common package used for cleaning 5/8" I.D. tubes of Trane, Blue Star, Thermax, Carrier, York and other units.
MODEL TCS-PORTO Chiller Tube Cleaning Systemis the most common system for cleaning chillers by users to whom size and portability is paramount.
CARBIDE DRILLSare used for cleaning tubes choked solidly with hard deposits.
Tube I.D. | Carbide Drill | |
inch | mm | |
3/4 | 19.1 | CB-750 |
7/8 | 22.2 | CB-875 |
1 | 25.4 | CB-1000 |
These tools consist of 4 stainless steel circular brushes that are mounted on a shaft and connected to a Universal Joint. These tools are used to clean soft to medium scales. Replacement circular brushes can be ordered when wear starts.
Straight Tube I.D. | Circular Brush Tool Model | Brush O.D. | Spare Brush Model (4 needed) |
Spare Universal Joint Model |
||
inch | mm | inch | mm | |||
1.1/8-1.5/16 | 28.6-33.3 | CBTS-1125 | 1 | 25.4 | CBSB-1125 | UCT-1063 |
1.3/8-1.9/16 | 35.0-39.7 | CBTS-1375 | 1 1/4 | 31.7 | CBSB-1375 | UCT-1063 |
1.5/8-1.13/16 | 41.3-47.1 | CBTS-1625 | 1 1/2 | 38.1 | CBSB-1625 | UCT-1063 |
1.7/8-2.1/16 | 47.6-52.6 | CBTS-1875 | 1 3/4 | 44.5 | CBSB-1875 | UCT-1250 |
2.1/8-2.5/16 | 54.0-58.7 | CBTS-2125 | 2 | 51.0 | CBSB-2125 | UCT-1250 |
2.3/8-2.9/16 | 60.3-65.1 | CBTS-2375 | 2 1/4 | 57.1 | CBSB-2375 | UCT-1250 |
2.5/8-2.13/16 | 66.7-71.6 | CBTS-2625 | 2 1/2 | 63.5 | CBSB-2625 | UCT-1250 |
2.7/8-3.1/16 | 73.0-77.8 | CBTS-2875 | 2 3/4 | 70.0 | CBSB-2875 | UCT-1250 |
3.1/8-3.5/16 | 79.4-84.2 | CBTS-3125 | 3 | 76.2 | CBSB-3125 | UCT-1250 |
These tools consist of 2 stainless steel circular brushes that are mounted onto a Double Universal Joint for maximum flexibility. These tools are used to clean soft to medium scales. Replacement circular brushes can be ordered when wear starts.
Curved Tube I.D. | Circular Brush Tool Model |
Brush O.D. | Spare Brush Model (2 needed) |
Spare Universal Joint Model |
||
inch | mm | inch | mm | |||
1.1/4-1.7/16 | 31.7-35.6 | CBTC-1125 | 1 | 25.4 | CBSB-1125 | UCT-1500 |
1.1/2-1.11/16 | 38.1-42.9 | CBTC-1500 | 1.1/4 | 31.7 | CBSB-1375 | UCT-1500 |
1.3/4-1.15/16 | 44.5-49.2 | CBTC-1750 | 1.1/2 | 38.1 | CBSB-1625 | UCT-1500 |
2-2.3/16 | 51.0-55.6 | CBTC-2000 | 1.3/4 | 44.5 | CBSB-1875 | UCT-1250 |
2.1/4-2.7/16 | 57.1-61.9 | CBTC-2250 | 2 | 51.0 | CBSB-2125 | UCT-1250 |
2.1/2-2.11/16 | 63.5-68.3 | CBTC-2500 | 2.1/4 | 57.1 | CBSB-2375 | UCT-1250 |
2.3/4-2.15/16 | 70.0-74.6 | CBTC-2750 | 2.1/2 | 63.5 | CBSB-2625 | UCT-1250 |
3-3.3/16 | 76.2-81.0 | CBTC-3000 | 2.3/4 | 70.0 | CBSB-2875 | UCT-1250 |
3.1/4-3.9/16 | 82.6-90.6 | CBTC-3250 | 3 | 76.2 | CBSB-3125 | UCT-1250 |
These tools use the Powermaster patented ergocentric cutters to clean hard scale from typically larger tubes that are found in boilers. The ergocentric cutters ensure that the same tooth does not touch the same spot when cleaning and prevents grooves being formed in the tube scale. All cone cutter tools are fitted with universal joints to negotiate bends in curved tubes
One Cone Tool: These consist of of 1 Cone fitted onto a Universal Joint and are used when scale build up is not severe.
Two Cone Tool: These consist of of 2 Cones fitted onto a Universal Joint and are used when scale build up is not severe.
Straight Tube I.D. | Curved Tube I.D. | One Cone Tool Model | Two Cone Tool Model | Cone Diameter | Spare Cone Model | Spare Universal Joint Model | |||
inch | mm | inch | mm | inch | mm | ||||
1.1/16-1.5/16 | 27.0-33.3 | 1.3/16-1.7/16 | 30.2-36.5 | OCT-1063 | TCT-1063 | 15/16 | 23.8 | SCT-937 | UCT-1063 |
1.1/4-1.7/16 | 31.7-36.5 | 1.7/16-1.11/16 | 36.5-42.9 | OCT-1250 | TCT-1250 | 1.1/16 | 27.0 | SCT-1062 | UCT-1250 |
1.3/8-1.9/16 | 35.0-39.7 | 1.11/16-1.15/16 | 42.9-49.2 | OCT-1375 | TCT-1375 | 1.3/16 | 30.2 | SCT-1187 | UCT-1250 |
1.1/2-1.13/16 | 38.1-46.0 | 1.15/16-2.3/16 | 49.2-55.5 | OCT-1500 | TCT-1500 | 1.7/16 | 36.5 | SCT-1437 | UCT-1250 |
1.3/4-2.1/16 | 44.5-58.7 | 2.3/16-2.7/16 | 55.5-61.9 | OCT-1750 | TCT-1750 | 1.11/16 | 42.9 | SCT-1687 | UCT-1250 |
2-2.3/8 | 50.8-60.3 | - | - | OCT-2000 | TCT-2000 | 1.15/16 | 49.2 | SCT-1937 | UCT-1250 |
Three Cone Tool: These consist of 3 Cones fitted onto a base which is fitted with a Universal Joint and are used for cleaning larger (2.5/16" I.D. and up) tubes where scale build up is severe.
Straight Tube I.D. | Curved Tube I.D. | Three Cone Tool Model | Spare Cone Model | Spare Base Model | Spare Universal Joint Model | ||
inch | mm | inch | mm | ||||
2.5/16-2.7/8 | 58.7-73.0 | 2.7/16-3.1/8 | 61.9-79.4 | PCT-2313 | SCT-937 | CTB-2313 | UCT-1250 |
2.13/16-3.3/8 | 71.4-85.7 | 3.1/16-3.11/16 | 77.8-93.7 | PCT-2813 | SCT-937 | CTB-2813 | UCT-1250 |
3.5/16-3.13/16 | 84.1-96.8 | 3.5/8-4.1/16 | 92.1-103.2 | PCT-3313 | SCT-1062 | CTB-2813 | UCT-1250 |
Scraper Tools use scrapper blades that 'fly out' when the tool is rotated, coming into contact with scale and scraping it out. These tools can be coupled with brushes for simultaneous 'finishing' of the cleaning operation as with carbide drills to initially drill through tubes that have very hard deposits.
Straight Tube I.D. | Curved Tube I.D. | Scraper Tool Model | ||
inch | mm | inch | mm | |
13/16-1.9/16 | 20.6-39.7 | 15/16-1.13/16 | 23.8-46.0 | SCR-813 |
1.7/16-2.1/16 | 36.5-58.7 | 1.11/16-2.9/16 | 42.9-65.1 | SCR-1438 |
1.11/16-3.1/16 | 42.9-77.8 | 2.7/16-3.1/16 | 61.9-77.8 | SCR-1687 |
These tools are used typically in boilers and other larger tubes that have a light to medium deposit. These tools use the Powermaster patented ergonomic cutting wheels that ensure the same tooth of the cutter wheel does not touch the same spot when cleaning. This prevents grooves being formed in the tube scale. The cutters 'fly out' when the tool is rotated and perform cleaning action.
Tube I.D. | Cylinder Cutter Tool Model | Spare Cylinder Cutter Model | |
inch | mm | ||
1.7/16-1.7/8 | 36.5-47.6 | CCT-1438 | CYC-1438 |
1.13/16-2.7/8 | 46.0-73.0 | CCT-1813 | CYC-1438 |
2.3/16-3.3/16 | 55.5-81.0 | CCT-2188 | CYC-2188 |
3.1/8-3.7/8 | 79.4-98.4 | CCT-3125 | CYC-2188 |
These tools use long stiff arms with Powermaster patented cone cutters on their ends, that spread out when rotated. These tools are used to clean light to medium deposits in large diameter tubes and pipes.
Tube I.D. | Wing Tool-Stiff Arm Cutter Model | Spare Cone Cutter Model | |
inch | mm | ||
1.11/16-4 | 42.9-101.6 | WTS-1688 | SCT-937 |
3.15/16-6.1/2 | 100.0-165.1 | WTS-3938 | SCT-937 |
4ft. (1.2m) long aircraft quality steel shafts to connect to drive.
- Model DS-300 to DS-500
- Model DS-562 to DS-750
4ft. (1.2m) long aircraft quality steel shafts to connect to driven shafts. Order quantities based on length of tube to be cleaned.
- Model DN-300 to DN-500
- Model DN-562 to DN-750
To Couple hollow drive shaft to drive.
- Model DC-300 to DC-500
- Model DC-562 to DC-750
To Couple 2 hollow shafts together.
- Model SC-300 to SC-500
- Model SC-562 to SC-750
To make pilot holes in deposits of completely clogged tubes.
- Model SD-312 to SD-500
- Model SD-562 to SD-750
Tube I.D.'s suited for | Model No. | Hollow Drive Shaft Model No. | Hollow Driven Shaft Model No. | Drive Coupling Model No. | Shaft Coupling Model No. | Starter Drill Model No. | |
inch | mm | ||||||
3/16-1/4 | 4.8-6.4 | C-10 | DS-300 | DN-300 | DC-300 | SC-300 | - |
3/8 | 9.5 | DS-312 | DN-312 | DC-312 | SC-312 | SD-312 | |
7/16 | 11.1 | DS-375 | DN-375 | DC-375 | SC-375 | SD-375 | |
1/2-9/16 | 12.7-14.3 | DS-437 | DN-437 | DC-437 | SC-437 | SD-437 | |
5/8-11/16 | 15.9-17.5 | DS-500 | DN-500 | DC-500 | SC-500 | SD-500 | |
3/4-13/16 | 19.1-20.6 | DS-562 | DN-562 | DC-562 | SC-562 | SD-562 | |
7/8-1 | 22.2-25.4 | CP-315 | DS-625 | DN-625 | DC-625 | SC-625 | SD-625 |
1.1/16-2 | 27.0-51.0 | DS-750 | DN-750 | DC-750 | SC-750 | SD-750 |
Build your own kit by adding price of Drive (C-10 or CP-315), Hollow Drive Shafts, Hollow Driven Shafts, Shaft Couplings, Drive Coupling based on length of tube to be cleaned and cleaning tools (Brushes, Carbide Drills, Buffing Tools).
We will supply all the above in a handy metal box at no extra charge ! The box will accommodate a maximum of 1 Drive + 4 Hollow Shafts + 5 Couplings + 18 Cleaning Tools (Brushes, Carbide Drills, Buffing Tools).
The Model "P" & "TC" cutter head is for straight tubes from 1-1/2" I.D. through 7" I.D. It is usually direct coupled to drive motor but flexible couplings, universal joints or flexible holders, are used to negotiate curved or bend tubes.
The model "P" & "TC" is for heavy and hard tube deposits as found in refinery and still tubes. It is tough in its parts and assembly as necessary to stand up in this service and it makes economical provision, as described below, for inevitable wear due to large forces which must transmit through the assembly. The model "P" & "TC" is conformed to do its work quickly and thoroughly even when deposits are of varying thickness and hardness.
Cone cutters, with tapered cutting edges at the front of the cutter head, expand against tube deposits by centrifugal force and break up uneven shoulders of scale. This is followed by long rows of expanding "no-track" cutter wheels which finish up with thorough, repeated cuts. Centrifugal force assures good working contact between tube deposits and cutting edges and " no track" means that cutters cannot fall into a pattern which skips over and leaves strips of scale behind.
The expansion range (range of cutter head diameters) of these cutter heads is considerable (See chart below.) and is due to (1) slotted cutter pin bearing bores and (2) intentional "play" in pin bearing inserts, features which include an economical bonus. Large cutter forces transmit through and wear the cutter pin bearing bore. By designing this bore into a replaceable insert, cutter body life is greatly increased, obviously providing increased economy of operation and service life.
Model No. | Tube I.D. inch |
Minimum Dia. Over Cutter inch |
Minimum Dia. Over Cutter inch |
Cone Cutter Set | Cylinder Cutter Set |
Cutter Pin Set |
Model | Model | Model | ||||
TC-14 | 1.1/2 | 1.3/8 | 1.23/32 | 1787-1 | 1788-2 | 1584-1 |
TC-11 | 1.3/4 | 1.5/8 | 2 | 1587-1 | 1588-2 | 1584-1 |
TC-17 | 1.7/8 | 1.11/16 | 2 | 2287-3 | 2288-6 | 1584-3 |
TC-16 | 2 | 1.13/16 | 2.3/16 | 1787-3 | 1788-6 | 1584-PY |
TC-13 | 2.1/8 | 1.15/16 | 2.5/16 | 1787-3 | 1788-6 | 1584-PY |
P-15 | 2.1/4 | 2.1/16 | 2.7/16 | 2487-3 | 3338-6 | 2484-PY |
P-9-S | 2.3/8 | 2.3/16 | 2.11/16 | C52-3 | C76-6 | 2484-3 |
P-9 | 2.1/2 | 2.1/4 | 2.13/16 | 1587-3 | 1588-6 | 1584-PY |
P-8 | 2.5/8 | 2.9/16 | 2.7/8 | 1087-3 | 1088-6 | 184-3 |
P-7 | 2.3/4 | 2.9/16 | 2.15/166 | 1087-3 | 1088-6 | 184-3 |
P-6-A | 3 | 2.11/16 | 3.1/8 | 1087-3 | 1088-6 | 184-3 |
P-6 | 3.1/8 | 2.13/16 | 3.1/4 | 1087-3 | 1088-6 | 184-3 |
P-5 | 3.1/4 | 3.1/16 | 3.9/16 | 987-3 | 988-6 | 184-3 |
P-4 | 3.1/2 | 3.3/16 | 3.13/16 | 787-3 | 788-6 | 884-3 |
P-3 | 3.3/4 | 3.9/16 | 4.3/16 | 887-B3 | 888-B6 | 884-3 |
P-2 | 4 | 3.3/4 | 4.1/2 | 887-3 | 888-6 | 884-3 |
P-1 | 4.1/4 | 3.13/16 | 4.3/4 | 887-3 | 888-9 | 884-P3 |
P-0 | 4.1/2 | 4.1/8 | 4.15/16 | 887-3 | 888-9 | 884-P3 |
P-10 | 4.3/4 | 4.3/8 | 5.3/16 | 887-3 | 888-9 | 884-P3 |
TC-19-H-S | 5 | 4.1/2 | 5.9/16 | 1287-3 | 1288-9 | 884-P3 |
TC-19-S | 5.1/4-5.1/2 | 4.7/8 | 5.15/16 | 1287-4 | 1288-12 | 884-P4 |
TC-20-S | 6 | 5.1/2 | 6.1/2 | 1287-4 | 1288-12 | 884-P4 |
TC-21-S | 6.1/4 | 5.3/4 | 6.3/4 | 11887-4 | 11888-12 | 884-P4 |
TC-22-S | 6.1/2 | 6 | 7.1/16 | 11887-4 | 11888-12 | 884-P4 |
TC-23-S | 6.3/4 | 6.1/4 | 7.5/16 | 8287-4 | 8288-12 | 2484S4 |
TC-24-S | 7 | 6.1/2 | 7.9/16 | 8287-4 | 8288-12 | 2484-S4 |
The Pine Jenny System has been in production for decades and has been an important tool used in the industry for removing boiler tubes. All of the parts required for the Pine Jenny System are compatible for use with Tube Pulling systems from Airetool, Wilson, Elliot and other manufacturers of "Pine Jenny style systems.
There are two types of spears which act as the mandrel for gripping the tube from the inside. One is for tubes from 3/8" up to 1.0" mainly oil coolers and heat exchangers, the other from 1.1/4" up to 3.0" for the boiler repair industry.
Used with the Powermaster Pneumatic Hammer to knockout tubes and tube stubs from the tube sheet. | ||||||||||||
Features of the Tube Drift/ Knockout Tool | ||||||||||||
|
The FM-1625 is a lightweight and powerful machine for Facing, Bevelling and Weld preparation. It is compact, easy to handle and quick to set up. It is used for jobs in restricted access areas. Used in environments on heat exchangers and condensers. |
Drive | Pneumatic | Electric |
Locking Range (mm) ID. | 20 - 42 | 20 - 42 |
Speed (RPM) | 240 | 178 |
Torque (Nm) | 27.5 | 45.0 |
Feeding Stroke (mm) | 23 | 23 |
Pneumatic Power (HP) | 0.45 | - |
Air Consumption (cfm) | 16 | - |
Air Pressure (psi) | 90 | - |
Electric Power (watts) | - | 59.5 |
Weight (kg) | 4.5 | 5.5 |
Drill down on either Torque Controller above for full Specifications: |
Either 120v or 240v / 60Hz or 50 Hz |
Electronic Drives for use with Torque Controllers |
Drivers for rolling tubes come in 4 sizes and depending on the tube size and material determines which driver is required. Each driver will be recognized by the torque controller and automatically adjusts the maximum torque output. See below for driver size required. |
The SWF Spring Balancers Series is the most commonly used spring balancer being shipped to over 26 countries worldwide. The design of the SWF Series balancers has been perfected into the most advanced Spring Balancer available. Within the swf die cast body is the Tapered designed drum to provide effortless operation of the swf series when the wire rope is extended or retrieved. The swf upper top hook is forged and fitted with a safety spring and also swivels 360 degrees. The swf bottom hook is high strength alloy steel for the proper securing of tools and equipment. On the top of the swf balancer is a secondary support cable point where a safety chain can be attached in the unlikely failure of the top hook. So overall the swf series spring balancers are the most common and the most available for all standard types of zero balancing. |
Remember! while making a selection:- The Total Weight of equipment and cables is the Capacity. |
The length of travel is how far the cable will travel from the unit (workable Length). |
Model No | Capacity Range | Travel | Unit Weight |
kg | Meters | kg | |
SWF-01 | 0.5-1.5 | 1.0 | 1.0 |
SWF-02 | 1.0-2.0 | 1.0 | 1.0 |
SWF-03 | 1.5-3.0 | 1.3 | 1.8 |
SWF-05 | 2.5-5.0 | 1.3 | 1.9 |
SWF-09 | 4.5-9.0 | 1.3 | 4.0 |
SWF-15 | 9.0-15.0 | 1.3 | 4.0 |
SWF-22 | 15.0-22.0 | 1.5 | 8.0 |
SWF-30 | 22.0-30.0 | 1.5 | 9.0 |
SWF-40 | 30.0-40.0 | 1.5 | 10.5 |
SWF-50 | 40.0-50.0 | 1.5 | 11.0 |
SWF-60 | 50.0-60.0 | 1.5 | 12.0 |
SWF-70 | 60.0-70.0 | 1.5 | 12.5 |
SWF-85 | 70.0-85.0 | 1.5 | 13.0 |
SWF-90 | 70.0-90.0 | 1.5 | 13.5 |
SWF-100 | 85.0-100.0 | 1.5 | 26.0 |
SWF-105 | 90.0-105.0 | 1.5 | 27.0 |
SWF-120 | 100.0-120.0 | 1.5 | 29.0 |
SWF-140 | 120.0-140.0 | 1.5 | 31.0 |
SWF-170 | 140.0-170.0 | 1.5 | 35.0 |
SWF-200 | 170.0-200.0 | 1.5 | 36.0 |
Bolt tensioning is now the preferred method of tightening bolts and studs on all critical applications. Bolt tensioners are designed for operation in a wide variety of applications including pipeline flanges, heat exchangers, pressure vessels, compressor covers, boiler feed pumps, windmills and many others. We provide a comprehensive range of bolt tensioners for optimum solutions to bolt tensioning requirements. Our Bolt tensioners and accessories are CE marked in accordance with Pressure Equipment and Machinery Directives, as applicable. In comparison to traditional tightening methods, tightening with bolt tensioners offers significant advantages: | ||||||||||
|
Hydraulic cylinders avail form us a wide range of Industrial Hydraulic Cylinders that are used for converting fluid power into linear mechanical force and motion. These hydraulic cylinders are used for converting the fluid energy to an output force in a linear direction in order to execute different jobs. Further, hydraulic cylinders are also includes pushing or pulling in engineering applications like machine tools, earth moving equipment and space applications. |
TheseHydraulic Power Pack for Khand Millare high pressure systems which are used along with Hydraulic Accumulators and a Gauge Board Assembly. The Power Pack is used to charge the accumulators with Hydraulic Oil to the desired pressure using the gauge board assembly.The pressure stored in the accumulators is used to exert force on the Hydraulic head. The Gauge board assembly is used to apply different pressures at the hydraulic heads on either side of the mill.The pressure can also be equalized using a gauge board assembly. | ||||||||
These Systems include the following: | ||||||||
|
POWERTECH Manufactures complete Hydraulic Systems for Belt Filter Presses. | ||||||||||
These Systems include the following: | ||||||||||
|
POWERTECH manufactures Hydraulic Power Packs and Cylinder for access control. Hydraulic Power Packs for Road Blocker and Bollard of the following types are manufactured: | ||||||||
|
POWERTECH manufactures Hydraulic Power Packs and Cylinder for access control. Hydraulic Power Packs for Road Blocker and Bollard of the following types are manufactured: | ||||||||
|
POWERTECH manufactures Hydraulic Power Packs and Cylinder for access control. | ||||||||
Hydraulic Power Packs for Road Blocker and Bollard of the following types are manufactured: | ||||||||
|
We design and manufacture Hydraulic Power Packs for a wide range of applications in Hydel Power Plants. | ||||||||
Applications: | ||||||||
|
POWERTECH manufactures accurate, precision machined C frame presses. This is a 25 Ton C frame Hydraulic Press for precision pressing. The press has a top and bottom hydraulic cylinder for simultaneous pressing. The pressing force and speed of the top and bottom cylinders can be adjusted independently. The press has a removable press bed plate and bolster plate. A linear transducer and a load cell are fitted and a load versus length of pressing graph is plotted and visible on the display panel. The machine is controlled by a PLC based panel. Safeties include 2 hand safety switches, pneumatically operated polycarbonate guards. |
POWERTECH manufactures Workshop presses with adjustable daylight. These are versatile tools for any maintenance workshop as small and largejobscan be pressed by changing the daylight. The presses can be made either with a hand operated pump or an electric driven power pack. This machine is of 10 ton capacity. |
We have been offering a wide range of Industrial Pneumatic Cylinder which is customized as per the specifications of our clients. |
We are the manufacturer of contact wheels in india as per the drawing for belt grinding machine of any size , for more information please email us |
Leveraging on our latest infrastructure facilities, we are able to offer a wide gamut ofRubber Contact Wheelfor Belt Grinding that is manufactured using state-of-the-art technology and latest machines. Our range of contact wheels is available in various diameter and width. We are engaged in offering a wide assortment of premium qualityRubber Contact Wheelfor Belt Grinding. These high gradeRubber Contact Wheelfor Belt Grinding are manufactured in accordance with international quality standards. | ||||||
Features: | ||||||
|
Leveraging on our enriched industry experience, we are engaged in manufacturing and exporting a huge gamut of Contact Wheel for Belt Grinding Machine that are manufactured using state-of-the-art technology and latest machines. Our range of contact wheels is available in various diameter and width. We fabricate this Contact Wheel for Belt Grinding Machine as per the industry standards using first grade raw materials procured from reliable vendors. | ||||||
Features: | ||||||
|
We offer excluding tubing sponges, silicone rubber sleeves (ITI approved), transparent tubings, inflatable gasket, cords, strip, squares, section, profiles, gaskets, cables, o-rings, tc gaskets, autoclave gaskets, silicone transparent platinum cured tubing, corona treater sleeves, etc. |
We offer , sponges, silicone rubber sleeves (ITI approved), transparent tubings, inflatable gasket, cords, strip, squares, section, profiles, gaskets, cables, o-rings, tc gaskets, autoclave gaskets, silicone transparent platinum cured tubing, corona treater sleeves etc. |
As a professional supplier in industries. We can produce kinds of superior quality rubber sheets which is used for many fields, including colorful rubber sheets, colorful dot rubber sheets, SBR rubber sheets, Neoprene rubber sheets, Butyl rubber sheets, CR rubber sheets, EPDM rubber sheets, fluorine rubber sheets, NBR rubber sheets, Silicone rubber sheets, rubber insertion sheets, white food Grade rubber sheets.We have advanced technology and equipments.We can produce completely according to the customer's requirements. |
We are manufacturer and exporter of all sizes of bar guide pad for hetran bar peeling machine, of long lasting quality.
These product are readily available with us at reasonable price. We also offer the bar guide pad nylon for hetran inc peeling machine. Powertech make bar guide pad are working successfully in each company of india who have hetran bar peeling machine.
We also supply bar guide for sas machine for bright bar manufacturar. . And for bar ledges plate for schumg wire drawing machine.
We are manufacturer of Bar Ledges plate made up of Brass/Gun metal. And we are supplying Bar Ledges Plate to Steel Bright Bar Plant. Our Customers are M/s Tata steel, Viraj Profile Ltd, Jindal, Chandan Steel etc. |
Silicone rubber tube is extruded from a soft and flexible elastomer. It offers excellent abrasion resistance, kink resistance with good strength & flexibility. It generally resists many solvents, oils, concentrated acids, dilute sodium hydroxide, non tainting of the product is very important and ideal in medical, food and the dairy industry. |
We are the manufacturer of silicon tubes in india, the tubes are avaliable in all sizes and custom size silicon tube also manufacture. |
Powertech offers disc and rings in various sizes and grades. |
Powertech offer disc and rings from 10" to 84" in various thicknesses. Disc and rings are normally produced upon request. Please send us you specific requirements for quoting. |
Powertech offers a FDA compliant oil filled Cast Nylon 6. This material can be in direct contact with foods. High wear resistance combined with low moisture absorption and good resistance against most cleaning agents makes this material a prefect substitute for stainless steel. The incorporated oil enables most applications to run without additional lubrication. Multiple color options are available. | ||||||||||||
|
Cast Nylon is also available as MDX Gray and MDX Blue, this material is designed for slightly higher loads capabilities | ||||||||||
|
|
We Are Leading Supplier And Manufacturers Of Mens Polo T Shirts In Chennai, Banglore, Hyderabad, Kerala And India. Men's Collar T-Shirt Are Offered By Us That Conform To Latest Fashion Trends And Have The Ability To Enhance The Beauty Of The Wearer To A Great Extent. Available In Plethora Of Colors, These T-Shirts Are Elegantly Designed On Various Alluring Patterns. Moreover, These T-Shirts Are Colorfastness And Shrink Resistant.
Features:
Specifications:
Our Exotic Collection Of Ladies Punjabi Dress Material Easily Make One Spell Bound. These Punjabi Dress Material Are Available In Various Sizes And Are Also Comfortable To Wear. Ladies Garment Is Designed With Accuracy Blending Fashion With A Feminine Look. The Use Of Excellent Fabrics Gives Them Durability, Extra Comfort To The Wearer And Is According To The Latest Fashion Trend. Ladies Apparel Has A Range To Suit Every Occasion.
We Have Been Engaged In Exporting Of Standard Designer Salwar Kameez Which Can Add Exceptional Grace To Your Personality. We Have Also Been Among's The Foremost Salwar Kameez Exporters And Ladies Salwar Kameez Suppliers. Our Collection Of Ladies Salwar Kameez Is Very Vivid And Vibrant. Our Salwar Kameez Has Been Aesthetically Made, Using Finest Fabric. We Know The Requirement Of Trend And In Order To Meet The Same We Keep On Incorporating New Changes In Our Collection.
Features:
|
We Are A Leading Manufacturer & Exporter Of Ladies Kurta Such As Ladies Casual Wear Kurta, Casual Wear Long Kurta, Designer Wear Long Kurta And Embroidered Long Kurta From India.
Leading Manufacturer And Exporter From Jaipur, Our Product Range Includes Traditional Kurtis Such As Traditional Ethnic Kurti, Bandhej Print Kurtis, Ethnic Kurtis And Panel Print Kurta.
KB Industries Manufacturer and exporter of quality Cotton Yarns of all kinds. We are looking for global queries. Our range of Cotton Yarns is available with following features and specifications:
Special Features:-