Kencraft India Pvt. Ltd.

Andheri East, Mumbai, Maharashtra

Fully operational auto electrical trainers Manufactured using original components Based on general auto electrical system, complete with the charging & lighting system Components include Alternator (motor driven), Headlights, Side lights, Indicators, Brake lights, Control dash panel, Relays & Battery isolator 6 Faults Insertion

Designed for the study of renewable energies: solar energy, wind energy and hydrogen fuel cell systems, The following topics are covered in this trainer :-Electrolysis mode for generating hydrogen & oxygen from water, Fuel Cell mode for generating electricity from hydrogen & oxygen, Polarization states for hydrogen fuel cells, Power a car with hydrogen fuel cell (reversible & mini fuel cell), salt water fuel cell, solar energy, super capacitor and hand crank, Electricity from Ethanol and water, Power a fan with electrical energy from the super capacitor, mechanical energy from the hand crank, two heat sources

Self contained, fully operational Air Conditioning Trainer Complete with the compressor, condenser, expansion valve, receiver dryer & evaporator Supplied with sight glasses to observe the state of charge refrigerant in the high & low pressure sides 6 Faults Insertion It offers an enhanced training resource, hands - on training with real components & greater understanding for students without the constraints of the modern motor vehicle

Fully sectioned petrol engine showing the working of an internal combustion engine

3ط Wye connected primary line with ground & neutral, Two sets of independent secondary lines to exhibit complexity of distribution network, Two sets of three 1f transformers to demonstrate 3f banking configurations, such as wye-wye, delta-delta, closed delta-wye, closed wye-delta, open-wye, open delta, etc.Fault introduction facility for troubleshooting, Each individual transformer winding is protected & designed to accept multiple faults

Glow Plug Trainer KE-AT0006 Fully operational diesel pre-heat glow plug system mounted on a bench stand Based on a generic diesel preheat glow plug system, complete with glow - plug relay, 4x glow-plugs, dash panel, ignition switch & ammeter.

Computer assisted training system with industrial machines, Prime mover Dynamometer module designed with permanent magnet DC Motor Generator with built - in digital display of speed or torque & internal external load control, PC based metering through Data Acquisition, Motors have open bell housings that allow interior view during operations, Easy connections with stacking safety banana plug leads

Fully operational 2-line Air Brake Tractor / Trailer unit Designed to understand the operating principles of an air brake system

Fully operational 2-line Air Brake Tractor / Trailer unit Designed to understand the operating principles of an air brake system

This training aid is electrically equivalent to a standard motor car Complete with charging, ignition, start & lighting system Ideal means of instruction & training in all aspects of automotive electrical systems

Fully operational high intensity discharge headlamp lighting system trainer Complete with HID headlights, headlight adjuster control unit & leveling sensor 10 Faults Insertion

Self contained, fully operational Fuel Injection / Engine Management Complete with all actuators & sensors Manufactured using original engine components Dry running operation using LEDs to indicate injection operation 10 Faults Insertion Pin out facility on all electrical components

Self contained, fully operational Brake Rig Cross diagonal hydraulic circuit Complete with master cylinder and servo, disc / drum assembly, handbrake & foot-brake Brake components mounted on a frame complete with castorS

Fully operational Hydraulic power assisted steering & suspension trainer Manufactured using original components Complete with the sub - frame, torsion bar, wishbone’s, front hub assembly, steering column, steering wheel, power steering rack & power steering pump

Self contained, fully operational ABS Trainer Complete with braking circuit & manufactured using original vehicle components Simulation of wheel lock to activate the ABS Pressure gauges indicate individual front & rear line pressures at each wheel Brake pedal kick back can be observed Diagnostic socket fitted for the connection of fault code readers

Fully operational diesel engine rig, complete with fuel, cooling, turbo & exhaust systems Complete with mechanical diesel injection system Typically RVA engine code or similar 10 Faults Insertion Engine Rig mounted on a self-contained stand complete with castors.

Self contained, fully operational electric window system trainer Complete with NS and OS electric window assemblies & switches Designed to understand the operating principles of an electrical window system Operation of each electric window motor can be observed 6 Faults Insertion

Self contained fully operational climate control trainer Designed to understand the operating principles of climate control system Including evaporator, compressor, condenser, associated pipe work, climate & electronic control 6 Faults Insertion

Fully operational motorcycle engine rig complete with the fuel, cooling, exhaust & ignition systems Based on a four cylinder motorcycle engine, complete with carbureted fuel system 10 Faults Insertion Engine Rig mounted on a self-contained stand complete with castors

Fully operational petrol engine rig, complete with fuel, cooling, exhaust & ignition systems Complete with carbureted fuel system & CB ignition system Typically GLA / GLW engine code or similar 10 Faults Insertion Engine Rig mounted on a self-contained stand complete with castors

Fully operational CB Ignition Turret Trainer, manufactured using original components Distributor operated via a variable speed control 6 faults insertion comprising of high resistance & open circuit faults