Industrial Pump #42744

Injection Pumps are designed to inject measured amounts of fluid into a reservoir or production system. They are often used in vehicles for pumping fuel into the cylinders of the engine. Suppliers of injection pumps are located across the United States and around the world. They meet many different quality standards and regulatory requirements.Injection pumps used in diesel engines are driven indirectly by gears or chains from the crankshaft and operate at very high pressures.A diesel fuel injection pump is coordinated by the timing belt of the engine to introduce fuel into the engine just before the cylinders compression stroke reaches the top. Because of the high pressure environment, working on a diesel injection pump requires certain safety measures to ensure that an operator is not injured by pressurized, escaping fuel. Another type of fuel injection pump is a rotary pump or distributor pump, used primarily in small trucks and cars. This type of fuel injection pump delivers fuel to the carburetor or fuel injection system. An electronic fuel injection pump system has built-in safety logic that will shut down the pump in the event of an accident or if it registers no oil pressure in the engine.

Hand Pumps and foot pumps are manually operated pumps that can driven by hand or foot via a handle or lever. This manual external force actuates an internal mechanism, which increases pressure for moving fluids such as gas, chemicals, or water. Hand lever and foot pedals are pushed up or down to begin the pump cycle, often requiring one stroke to draw the fluid and another stroke to discharge it, as is typical in many displacement pumps.

Corrosion resistant, Impact resistant, Lightweight, Continuous duty when fully submerged. Swing or vertical float option
For handling water with suspended solids upto 50 mm sphere
Non Clog vortex impeller
Vertical discharge with female flange
Motor - 2800 rpm motor with 'F' class insulation, suitable for three phase power supply of 415 VAC, 50 Hz.
Motor is jacketed & filled with the coolant. Thus the pump is suitable for working in worst working conditions, having capacity for longer period of dry running.
Dual ball bearings
Dual mechanical seal - Motor side - Carbon Vs. Ceramic; Pump size - Silicon Carbide Vs. Silicon Carbide

Openwell submersible pumps are replacing centrifugal pumps at a number of places because of some of the inherent advantages, such as.
No separate foundation is required.
Cooling is much better & hence longer life.
Convenient to move from place to place.
oot Valve is not required.
Suction head is eliminated.

DC Powered Pumps use direct current from motor or solar power to move fluid in a variety of ways. Motorized pumps operate on 6, 12, 24, or 32 volts of DC power and use hand-operated, electric, pneumatic, or hydraulic motors. Solar-powered DC pumps use photovoltaic (PV) panels with solar cells that produce direct current when exposed to sunlight.
Many DC powered pumps use centrifugal force or positive displacement to move fluids. Centrifugal pumps apply centrifugal force to generate velocity, use rotating impellers to increase velocity, and push fluids through an outlet valve. Positive displacement pumps use rollers, gears, or impellers to move fluid into a fixed cavity so that when liquid exists, the vacuum that is created draws in more fluid. Diaphragm pumps are the most commonly used positive displacement pumps. They include a single diaphragm and chamber, as well as suction and discharge check valves to prevent backflow.A variety of special DC powered pumps are available.

Hand Pumps and foot pumps are manually operated pumps that can driven by hand or foot via a handle or lever. This manual external force actuates an internal mechanism, which increases pressure for moving fluids such as gas, chemicals, or water. Hand lever and foot pedals are pushed up or down to begin the pump cycle, often requiring one stroke to draw the fluid and another stroke to discharge it, as is typical in many displacement pumps.

Centrifugal Monoblock Pumps are replacing centrifugal pumps at a number of places because of some of the inherent advantages, such as.Uni-casing no air lock problem.Balanced and rigged construction.

We manufacture stout Centrifugal Monoblock Pumps, which reflect a true example of modern technology. Our customized centrifugal monoset pumps have vast application, which include irrigation, fire lighting, dewatering of mines, booster application etc. We proffer unmatched centrifugal monoset pumps, which are easily available at the most competitive price.

Centrifugal Monoblock Pumps are replacing centrifugal pumps at a number of places because of some of the inherent advantages, such as.

Low cost.

No centrifugal switch.

Salient Features of Centrifugal Monoblock Pumps

Uni-casing no air lock problem.

Balanced and rigged construction.

No centrifugal switch.

Less operational and maintenance cost.

Application Of Centrifugal Monoblock Pumps

Industrial & public water supply schemes, Domestic water supply, Lift irrigation schemes. Drip/ Sprinkler Irrigation schemes, fire lighting, booster application, cooling water. Circulation, Ornamental fountain installation and air conditioning plants. Dewatering of mines, offshore, platforms, etc.

Construction of Centrifugal Monoblock Pumps

Wet squirrel cage induction type, water cooled, water lubricated motor. All bearings are water lubricated.