Other Products / Services #5894388

Description and Specification for Lab Tenders

Soil Hydrometer.

Used for grain size analysis of soils where more than 10% of the material will pass through 75 microns B.S. sieve. Manufactured from clear transparent glass having uniform clarity throughout the upper end on which density scale is engraved.

The scale range is 0.995 to 1.030 0 density (gms./cc) at 27oC smallest division on the scale is 0.0005. Note: Hydrometer for other liquids also available. civil lab equipments manufacturers

Soil Testing Lab equipment manufacturers, exporters and Soil Testing Lab suppliers

Description and Specification for Lab Tenders

Mud Balance.

Designed to find out specific gravities of semi liquids like mud and other liquids having densities in the range 0.8 to 2.5. It has a

stainless steel bam calibrated specific gravities from 0.8 to 2.5. A stainless steel cup with lid and overflow vent is fitted on one side of the beam. A counter weights with cursor slides over the graduated scale. The beam has a knife-edge at centre which rests in a fulcrum fitted in the stand. Leveling screws and spirit level are fitted to the stand. civil lab equipments manufacturers

Soil Testing Lab equipment manufacturers, exporters and Soil Testing Lab suppliers

Description and Specification for Lab Tenders

Proctor Needles (Spring Type).

The instrument consists of a needle attached to a spring loaded plunger, the stem of which is calibrated to read 0 to 40 kg division.

Long stem is graduated at every 12.5mm to read depth of penetration and for use with needles of larger areas. The small penetration stem is also graduation in 12.5mm division and is used with needles of smaller areas. Needle points one each of 0.25, 0.5, 1.0, 1.5, 2.0, 3.5 and 6.0 sq Cm. And one tommy pin is supplied. Complete as above in a wooden carrying case. civil lab equipments manufacturers

Soil Testing Lab equipment manufacturers, exporters and Soil Testing Lab suppliers

Description and Specification for Lab Tenders

Plummet Balance.

Conventionally particle size distribution analysis is carried out using pipette and hydrometer methods.

Whereas in hydrometer method it is possible to determine particle sizes in the range 75microns, the method involves computation and it is time consuming. The pipette method can be used for determining only the percentage of specific sizes less than 0.02, 0.006 and 0.002mm as a percentage of total soil sample. The plummet balance method to determine sub sieve particle size for the entire range is very rapid and only manipulation of height of the balance, so that plummet sinks to the right depth is required. The percentage of soil in suspension is directly indicated by a pointer over a graduated scale. A vertical rod is mounted on a sturdy base having leveling screws. A pointer with steel pivots turns is jewel bearing an moves over a graduated scale. Scale graduations are market 0-100% x 2% To the other end of the pointer a plummet is hanged.Rack and pinion arrangement is provided on the vertical rod for adjusting the height. Supplied with a chart showing relationship between K and temperature of suspension of soils of varying specific gravity from 2.4 to 2.8 to help in solving stroke's equation. Supplied complete with one Perspex plummet one measuring jar and one rider weight for zero adjustment and rider weight for adjusting the pointer to 100%. civil lab equipments manufacturers

Soil Testing Lab equipment manufacturers, exporters and Soil Testing Lab suppliers

Description and Specification for Lab Tenders

Core Cutter.

This is used for determination of in situ dry density of natural or compacted fine grained soil, free from aggregates.

A cylindrical cutter is used to extract a sample of the soil with the help of a dolly and rammer. From the weight, density and the moisture, and dry density of the soil is ready calculated. It consists one each of: cylindrical core cutter mode of steel, 127.3mm. Long and 100mm internal diameter. Steel dolly, 25mm high with a lip to enable it to be located on top of the core cutter, rammer with detachable steel rod. Spare, Optional Extra And Accessories:-1. Cylindrical core cutter 100mm i.d. x 175mm long2. Dolly3. Test form pad of 50. civil lab equipments manufacturers

Soil Testing Lab equipment manufacturers, exporters and Soil Testing Lab suppliers

Description and Specification for Lab Tenders

Density Bottle (GAY LUSSAC Type).

For determining the particle density (specific gravity) of sand, fine aggregate and filler. Capacity 25ml, 50ml, 100ml, 250ml, 500ml and 1000ml. civil lab equipments manufacturers

Soil Testing Lab equipment manufacturers, exporters and Soil Testing Lab suppliers

Description and Specification for Lab Tenders

Particle Density By Gas Jar Method (End-Over-End Shaker).

This method applies for soil containing upto 10% of particles retained on 37.5 mm sieve. The equipment is used to rotate two gas jars at approx. 50 R.P.M. Glass Jar is 1 litre in capacity with rubber bung. civil lab equipments manufacturers

Soil Testing Lab equipment manufacturers, exporters and Soil Testing Lab suppliers

Description and Specification for Lab Tenders

Colour Standard Chart.

For the determination of organic impurities in soils and fine aggregates. civil lab equipments manufacturers

Soil Testing Lab equipment manufacturers, exporters and Soil Testing Lab suppliers

Description and Specification for Lab Tenders

Sampling Tubes.

Sampling tubes for collection undisturbed samples of 38mm dia for triaxial strength and unconfined compressive strength either straight from the field or from a sample of larger diameter.

The wall thickness is maintained approximately 17 per cent. Both relieved and unrelieved sampling tubes are available. In the relieved type of tube, the internal diameter is relieved by about 0. 5mm (inside clearance 2%) beyond approx. 19mm length from the cutting edge of the tube. This is most suitable for highly cohesive soils. In the unrelieved type, the internal diameter is uniform through out. This type is most suitable for soil of low cohesion. These 38mm dia tubes are available in different lengths. Unrelieved(a)150mm, (b) 200mm, (c) 225mm (d) 300mm long. Relieved(a) 150mm (b) 200mm, (c) 225mm, (d) 300mm long. civil lab equipments manufacturers

Soil Testing Lab equipment manufacturers, exporters and Soil Testing Lab suppliers

Description and Specification for Lab Tenders

Split Spoon Sampler.

Description and Specification for Lab Tenders

Frame Sieves 300mm Dia And 450mm Dia.

Sizes available: 125mm, 106mm, 100mm, 90mm, 80mm, 75mm, 63mm, 53mm, 50mm, 45mm, 40mm, 37. 5mm, 31. 5mm, 26. 5mm, 25mm, 22. 4mm, 20mm, 19mm, 16mm, 14mm, 13. 2mm, 12. 5mm, 11. 2mm, 10mm, 9. 5mm, 8mm, 6. 7mm, 6. 3mm, 5. 6mm, 4. 75mm, 4. 0mm, 3. 35mm, 2. 36mm, 1. 18mm, 1. 00mm. Lid and receiver in g. I. Frame for 300mm dia and 450mm dia sieves. civil lab equipments manufacturers

Soil Testing Lab equipment manufacturers, exporters and Soil Testing Lab suppliers

Description and Specification for Lab Tenders

California Bearing Ratio Spares.

CBR mould complete with extension collar and perforated base plate, made of gunmetal.

CBR mould complete with extension collar and perforated base plate, made of steel." Perforated swell plate with adjustable stem and lock nut, made of gunmetal. Perforated swell plate with adjustable stem and lock nut, made of steel.Solid base plate, made of gunmetal. Solid base plate, made of steel. Cutting collar. civil lab equipments manufacturers

Soil Testing Lab equipment manufacturers, exporters and Soil Testing Lab suppliers

Description and Specification for Lab Tenders

California Bearing Ratio Apparatus (Motorised).

Similar to above but supplied with bench mounting type 5000kgf. capacity load frame motorised, in place of load frame hand operated.

The lead screw of the load frame has a single constant rate of travel of 1.25mm/min. Salient Features Accessories for Laboratory C.B.R. Apparatus :High sensitivity Proving Ring 3000kg. capacity with calibration chart and carrying case. Dial Gauges 2 Nos.0.01mm x 25mm.Annular metal weight 5 kg. 147mm dia with 53 mm dia. central hole. Slotted metal weight, 5 kg. 147mm dia with 53 mm dia slot. Note: Proving Ring of other capacities are also available. civil lab equipments manufacturers

Soil Testing Lab equipment manufacturers, exporters and Soil Testing Lab suppliers

Description and Specification for Lab Tenders

Dead Weight Type Oil Water Constant Pressure System.

This device is used to maintain cell pressure constant for a long duration and the system can be used in place of convensional constant pressure system using mercury posts where certain minimum heights are required.

Problems like deairiation of pump, leakage of mercury etc. are eliminated in this system. This unit is smaller in volume and can be used in mobile laboratory also. This can maintain pressure in the cell upto 20 kg/cm.sq. Pressure is maintained constant in the system by a balancing calibrated weights on a spindle against a column of oil, operating under constant feedback. Salient Features Construction :The system consists of an oil pump continuously driven by an electric motor during the test period. The internal components are housed in a strong compact housing. The piston on which weights are kept rotates with minimum friction. A transparent Oil Water vessel is provided on transmit pressure to the cell. A hand pump provided facilitates priming and to maintain constant pressure during power failure.Specifications :Range 0-20 bar (0-20 kg/cm) Steps of Pressure 0.5 bar (0.5 kg/cm)Accuracy +0.5%Electric Supply 230 Volts, Single Phase, 50 Hz, A.C.supply Supplied complete with Pressure Guage, flow valves, connecting Pressure hose and set of weights to give maximum pressure of 20 bar (20 kg/cm). civil lab equipments manufacturers

Soil Testing Lab equipment manufacturers, exporters and Soil Testing Lab suppliers

Description and Specification for Lab Tenders

Extractor Frame Hydraulic.

This extractor Frame is used for taking ut soil samples compacted or undisturbed, from 100 mm dia and 150 mm dia cylinders such as core cutters,

Proctor moulds, C.B.R. moulds etc. Salient Features Specifications : It consists of a 5 Tone capacity hand operated, hydraulic jack mounted on a suitable frame. Two plungers, one for 100 mm dia and the other of 150 mm dia moulds are supplied. One thrust plate for 150 mm dia and one for 100 mm dia specimens are also supplied. Height of thrust plate is adjustable. Accessories : Set of Plungers adapters and thrust plates for 38 mm, 50 mm and 75 mm dia specimen. civil lab equipments manufacturers

Soil Testing Lab equipment manufacturers, exporters and Soil Testing Lab suppliers

Description and Specification for Lab Tenders

High Speed Stirrer.

This is for mechanical analysis and also other laboratory applications for stirring.

Speed approximately 4000rpm under load. A dispersion cup is supported on a rest on the stand of the stirrer and has a removal baffle.For operation on 230-250 volts AC Supplied without dispersion cup or baffle. civil lab equipments manufacturers

Soil Testing Lab equipment manufacturers, exporters and Soil Testing Lab suppliers

Description and Specification for Lab Tenders

Pycnometers Bottles.

These bottles are used for relative density measurements, made from borosilicate glass with capillary bored stopper. Capacities available (a) 50 cc and (b) 100 cc.

Soil Testing Lab equipment manufacturers, exporters and Soil Testing Lab suppliers

Description and Specification for Lab Tenders

Split Spoon Sampler.

This is used for Standard Penetration Test. For determining penetration resistance (N value) of soil which can be related to unconfined Compressive strength, Penetration resistance (N value) of soil is determined by giving a number of blows with a 65 kg. weight falling through a given distance of 75 cm required to penetrate the assembly to a depth of 30 cm, when properly seated on the ground. Salient Features Specifications : The sampler is made from a steel tube split lengthwise and held together by a head fitted with a ball check valve and a hardened steel shoe of inside cutting edge of 35 mm dia. The sampler is 35 mm I.D. and 50.8mm in outer diameter and 508 mm / long. One adapter to connect 'A' type drill rods is also supplied.Spares: Body of split spoon sampler, shoe of split spoon sampler, head of split spoon sampler. civil lab equipments manufacturers

Soil Testing Lab equipment manufacturers, exporters and Soil Testing Lab suppliers

Description and Specification for Lab Tenders

Ball Mill For Grinding Lime Mortar.

It is of welded steel construction, having an internal diameter of 12 inch x 13.5 inch long (volume 1 cu.ft.) and is made of 5/16 inch thick steel plate.

Material Testing Lab equipment manufacturers, exporters and Material Testing Lab suppliers The drum is supported on heavy duty ball bearings on the two ends. It has an opening of 4 inch width along the full length of the drum. An air and water tight cover is provided to close the opening after the specimen has been but inside the drum. The speed of rotation is 28-30 r.p.m. The pug mill has an arrangement for being held in any position. A revolution counter for recording the revolutions of the mill is fixed on the machine. Twelve 3/4 inch dia steel balls are also supplied with the unit. It is fitted with a 1/2 H.P. electric motor to operate on single phase, 220/230 volts A.C. supply civil lab equipments manufacturers

Description and Specification for Lab Tenders

Density Basket.

Salient Features Made of brass with stainless steel wire mesh 6.3mm size ruggedly constructed, approximately 20cm dia x 20cm high. Complete with handle. civil lab equipments manufacturers

Material Testing Lab equipment manufacturers, exporters and Material Testing Lab suppliers

Description and Specification for Lab Tenders

This instrument is used for determination and checking of bitumen percentage in bituminous mix, the mix is added with a solvent and dissolved bitumen is removed by centrifugal action.
Material Testing Lab equipment manufacturers, exporters and Material Testing Lab suppliers Consists of a removable aluminum rotor bowl, capacity 1500 gms. This shaft and thus the bowl is rotated fast manually by enclosed gears in the cast body and handle. Solvent is introduced during the test through the holes in the cap of the housing. A drain is provided to collect dissolved bitumen coming out of the rotating bowl and getting collected in the housing. Salient Features Centrifuge Extractor (Motorized) : Same as above but shaft is rotated by an electric motor and gear. Care is taken to prevent solvent entering into the rotor of electrical motor. Operates on 230 Volts A.C. single phase. Accessories : 1. Filter paper disc (packet of 100nos.) 2. Benzene

Description and Specification for Lab Tenders

Specifications: Drive by Diesel or Petrol / Kerosene Engine Diamond wheel of 300mm dia.
Bitumen-Asphalt Testing Lab equipment manufacturers, exporters and Bitumen-Asphalt Testing Lab suppliers suitable for a cut of depth unto 110 mm is supplied with standard outfit The trolley on which the engine is fitted also has a water rank which supplies a stream of water to keep the cutting blade cool during the operation. Adjustment to control depth of cut is also provided. A safety Guard is provided over the diamond wheel. Diamond wheels up to 600 mm dia., can be supplied at extra cost. civil lab equipments manufacturers

Description and Specification for Lab Tenders

This device was developed by U.S. Bureau of Public Roads and is used timesaver deflections of flexible pavements.
Bitumen-Asphalt Testing Lab equipment manufacturers, exporters and Bitumen-Asphalt Testing Lab suppliers The light weight instrument is supplied in two parts for assembling on site with easy hand tools. In use one end of the beam rests at a point under investigation while the beam is pivoted at the centre. The free end carries a dial gauge to record the deflections. The other end is kept on a stable platform. The beam ratio is 2:1 which magnifies even small deflections. Supplied with a dial gauge 0.01 x 25mm. This is a light weight dismount liable instrument and easy to carry. civil lab equipments manufacturers

Description and Specification for Lab Tenders

For 15cm dia x 30cm length cylinders. Salient Features Specifications The set comprises of a cylinder capper, a cylinder carrier and a ladle.
Cement and Concrete Testing Lab equipment manufacturers, exporters and Cement and Concrete Testing Lab suppliers The cylinder capper consists of a base on which two accurately machined plates are mounted vertically. One plate is firmly fixed and the other one is adjustable horizontally. Two plates are provided with holders of holding the cylinder in position. The holders are split and the bottom half of each holder is fixed firmly and the top half of each is removable and bolted down to the lower half. On the upper parts of the vertical plates 'V's are provided for pouring the capping compound. Two spacers are also provided. Complete with cylinder carrier and ladle for molten compound. civil lab equipments manufacturers

Description and Specification for Lab Tenders

For capping compression cylinder specimens. This apparatus can be used both in the laboratory and in the field.
Cement and Concrete Testing Lab equipment manufacturers, exporters and Cement and Concrete Testing Lab suppliers The specimens capped in this apparatus have plane parallel faces. Salient Features Specifications: For cylinders 150mm dia x 300mm long. Consists of a base with an upright. The upright serves as a guide for positioning the capping plate and the cylinder. The 19mm thick capping plate is machined accurately. There is a recess in the plate for keeping the molten capping compound and to position cylinder. Complete with cylinder carrier and ladle. civil lab equipments manufacturers

Description and Specification for Lab Tenders

This is used for determining the workability of building limes. Salient Features Specifications.
Cement and Concrete Testing Lab equipment manufacturers, exporters and Cement and Concrete Testing Lab suppliers The flow table consists of a 30cm. dia ground and polished steel plate with three inscribed annular circles. 7, 11 and 19cm. dia. The table top is arranged for a free fall of 12.5mm by a cam action. Supplied complete with one brass conical mould, 65mm ID at base and 40mm ID at top, height of the mould 90mm. civil lab equipments manufacturers

Description and Specification for Lab Tenders

Concrete mixer laboratory type, electrically operated. Designed to remove the burden- some work of hand mixing. Uniform thoroughly mixed batches can be produced.
Cement and Concrete Testing Lab equipment manufacturers, exporters and Cement and Concrete Testing Lab suppliers The counter balanced drum is easy to tilt 1.1/2 to 2cu.ft.mix. The total drum volume is however 3cu.ft. Mounted on a sturdy rubber tyred stand, and the drum is mounted for end discharge and equipped with end towing pole. Equipped with h.p. electric motor. Suitable for operation on 220/230 volts A.C. single phase. civil lab equipments manufacturers

Description and Specification for Lab Tenders

Used for finding specific gravity of Hydraulic Cement. Made from Borosil glass. The flask is 243mm in total height, .
Cement and Concrete Testing Lab equipment manufacturers, exporters and Cement and Concrete Testing Lab suppliers having a bulb of 90 mm dia of 250ml approximate capacity. The long neck of the flask has at top a funnel of 50mm dia in which fits a ground glass stopper. The neck has over-all 11mm I.D. upper portion is graduated from 18 ml to 24ml with 0.1ml graduation. Just at the bottom of the neck 1ml capacity is marked in between there is 17ml capacity bulb. civil lab equipments manufacturers

Description and Specification for Lab Tenders

It is used to measure the drying shrinkage of concrete autoclave expansion of Portland cement and potential expansive reactivity of cement aggregate combinations in mortar bars during storage, on self drying. Salient Features Specifications.
Cement and Concrete Testing Lab equipment manufacturers, exporters and Cement and Concrete Testing Lab suppliers The instrument consists of a channeled base over which two vertical pillars are fixed. An adjustable cross plate is at the top. A dial gauge, reading to 0.002mm x 12mm. can be fixed to the top cross plate. The plunger end of the dial gauge can be located upon a 6.5mm. dia ball or other reference point cemented in the specimen. On the base there is a similar recessed seating in which can be placed a second ball or reference point in the specimen. Complete with a stainless steel standardization bar with insulated grip and with 6.5mm dia. Balls mounted in the ends. The unit can be supplied with a 0.0001inch x 1/2inch dial gauge at extra cost. civil lab equipments manufacturers

Description and Specification for Lab Tenders

It is used for mixing cement pastes, mortars and pozzolanas. Salient Features Specifications: the apparatus consists of an epicyclic type stainless steel paddle imparting both planetary and revolving motion by means of gears.
Cement and Concrete Testing Lab equipment manufacturers, exporters and Cement and Concrete Testing Lab suppliers It has two speeds of 140 + 5 R. P. M. and 285 + 10 r. P. M. with planetary motions of approximately 62 R. P. M. + 5 R. P. M. and 125 R. P. M. +/-10 R. P. M. respectively. The stand of the mixer has arrangement to raise or lower the bowl. Complete with stainless steel bowl of about six litres capacity. Suitable for operation on 230 volts, 50 cycles, single phase, A. C. Supply. civil lab equipments manufacturers

Description and Specification for Lab Tenders

An increasing number of contractual obligations call for various forms of vibro-compacted concrete for achieving a better and more consistent mixture.
Cement and Concrete Testing Lab equipment manufacturers, exporters and Cement and Concrete Testing Lab suppliers The Needle Vibrator is recommended for vibro-compaction of test cylinders and beams at site and in the laboratory. This instrument can also be used at small construction sites. A motor fitted on a swivel base drives a flexible shaft, which in turn, vibrates the needle at about 10, 000 vibrations per minute. (approx.) Salient Features Specifications: Needle Vibrator with a 25mm. diameter x 350mm long needle, a one meter long flexible shaft and a motor drive with a swivel head and on/off switch. Wired for 230 V. Single phase, 50 Hz. civil lab equipments manufacturers

Description and Specification for Lab Tenders

Used for determining the slump of fine aggregate in the determination of bulk and apparent specific gravity and absorption of fine aggregate.
Cement and Concrete Testing Lab equipment manufacturers, exporters and Cement and Concrete Testing Lab suppliers Salient Features Specifications: the equipment comprises of -a conical metal mould1. 5 inch dia at the top, 3. 5 inch dia at the base and 2. 7/8 inch in height. A metal tamping rod weighing 12 ounces and having a flat circular tamping face 1 inch in diameter. civil lab equipments manufacturers

Description and Specification for Lab Tenders

This is for use while casting a cement briquette. Salient Features Specifications: The standard spatula consists of a steel blade, of a special shape. A wooden handle is fixed to the stem of blade. The weight does not exceed 340gms. civil lab equipments manufacturers.
Cement and Concrete Testing Lab equipment manufacturers, exporters and Cement and Concrete Testing Lab suppliers

Description and Specification for Lab Tenders

This is used for compacting concrete into cube moulds. This rod is made of steel. It is 16mm diameter, 60mm in length and rounded or bullet shaped at one end. civil lab equipments manufacturers.
Cement and Concrete Testing Lab equipment manufacturers, exporters and Cement and Concrete Testing Lab suppliers

Description and Specification for Lab Tenders

Made of steel this is 40cm long, having a ramming face of 25mm SP. Other end has a grip, weight approximate 2 kgs.
Cement and Concrete Testing Lab equipment manufacturers, exporters and Cement and Concrete Testing Lab suppliers

Description and Specification for Lab Tenders

Specifications Weight approximately 210gm. Best quality with hardwood handle Blade length approx. 200mm. civil lab equipments manufacturers.
Cement and Concrete Testing Lab equipment manufacturers, exporters and Cement and Concrete Testing Lab suppliers

Description and Specification for Lab Tenders

Specifications 100 to 150mm long steel blade with straight edges. civil lab equipments manufacturers.
Cement and Concrete Testing Lab equipment manufacturers, exporters and Cement and Concrete Testing Lab suppliers

Description and Specification for Lab Tenders

Also Called Mould Vibrator Or Mortar Cube Vibrator Concrete moulds are easily cast by using a tamping bar or a vibrating table.
Cement and Concrete Testing Lab equipment manufacturers, exporters and Cement and Concrete Testing Lab suppliers However air tapped in cement mortar paste can not be thus removed while casting cement mortar moulds. Easy method is to impart greater vibration of lesser amplitude to the mould while casting. This is achieved in a vibrating machine. Vibration machine is used for the preparation of mortar cubes for the determination of compression strength of ordinary and rapid hardening Portland cement, low heat portland cement, portland bleast furnace cement and high alumina cements. Salient Features Specifications: The machine consists of a vibrating frame assembly and an electric motor mounted on a sturdy base. The complete frame assembly consists of a vice to hold a 7.06cm cube mould and two studs threaded at top and a hopper to feed the sample in the mould. This assembly is supported on four springs and has an in built rotating shaft which rotates eccentrically and thus imparts vibrations to the entire frame. A balance weight is an intergral bottom part of the frame. The center of gravity of the assembly is brought to the center of the eccentric shaft or within a distance of 25mm mould. The frequency of vibration is 12000 400 vibration per minute. Supplied complete with on 7.06cm cube mould with loose base plate, a time switch 0-5mins x 1min and certificate of vibration from a standard laboratory. Spares : Set of Springs, Belt and Belt guard. civil lab equipments manufacturers

Description and Specification for Lab Tenders

Vibrating Table.

The Vibrating Table is used for compacting concrete cubes and cylinders. Salient Features Specifications: It is designed to carry a load of 140 kg.

Cement and Concrete Testing Lab equipment manufacturers, exporters and Cement and Concrete Testing Lab suppliers The apparatus consists of a motor fitted with a variable pitch pulley housed in a cabinet. The vibrations are imparted by means of off-balance masses rotating on a shaft of a vibrator clamped to the underside of the table top. The table top is 50cm x 50cm. and has stops along its edges to prevent moulds from walking off the table during vibration. A cross arm adjustable on a vertical rod at the center of the table is provided to hold the moulds while operating the table. The variable pitch pulley arrangement permits the frequency to be varied steplessly between a maximum of 3600 vibrations per minute. A speed regulation handle is provided for increasing or decreasing the frequency. A switch is provided for starting the motor, suitable for operation on 440 volts, 3 phase, 50 cycles, A.C.supply. Vibrating Tables of table top size 75cm x 75cm as well as 100cm x 100cm are also available. civil lab equipments manufacturers

Description and Specification for Lab Tenders

Concrete Drum Mixer.

Description and Specification for Lab Tenders

Concrete Core Drill.

Concrete Core Drill - Often, existing concrete structures will need to be examined and tested to ensure the concrete remains of adequate strength and durability. This test is used to determine the compressive strength of a concrete core, which has usually been extracted from an existing structure. The value of compressive strength can then be used in conjunction with other measured properties to assess the condition of the concrete Extraction of concrete cores, achieved by rotary drilling using a diamond tipped hollow barrel, serve as a means of taking a sample of concrete which can then be used to determine various physical properties, but most commonly compressive strength.Cores can generally be extracted from wherever access allows, and would include floor slabs, walls and columns. 10cm diameter cores, generally afford the minimum diameter required for a representative sample and require less reinstatement than larger diameter cores. 15cm diameter cores will generally give more representative samples than smaller diameters but require more reinstatement. civil lab equipments manufacturers

Soil Testing Lab equipment manufacturers, exporters and Soil Testing Lab suppliers

Description and Specification for Lab Tenders

Laboratory Sieves.

Laboratory Sieves - Recommended for grinding of dry chips. Also for a great variety of commercial dry materials. Unit havin two stationary steel blades and rotary with steel edges provided in the cast iron chamber.A removable safety glass sheet plate form the face of chamber permits observation during operation. Willey mill is fitted on substantial cast iron case. Complete unit supplied with alumnium/cast chamber, polished hopper with cover, wooden plugger, three delivery tubes mounted eith sieves cloth mesh no 20, 40 and 60 mesh, one allen key for adjusting blades and 3 glass jars, brush etc. civil lab equipments manufacturers

Soil Testing Lab equipment manufacturers, exporters and Soil Testing Lab suppliers

Description and Specification for Lab Tenders

Double Beam Spectrophotometer.

Technical Specifications Wavelength Range 190-1100 nm Mode Basic/Quantitative/Wavelength Scan/DNA Protien Test/Kinetics Scanning Speed Fast / Medium / Slow Wavelength Accuracy +0.1 nm Bandwidth 1 nm Wavelength Reproducibility 0.1 nm Photometric Display Range 0-200 % T, -0.3 - 3.0 A, 0-9999 C Photometric Accuracy +0.3 % T Photometric Repeatability +0.2 % T Stability 0.001A/h @ 500 nm Baseline Flatness +0.001 A Noise +0.001A Stray Light