Lath Industries

Murbad, Thane, Maharashtra

Cost-effective and widely available. Longer lifespan than traditional copper electrodes due to their corrosion-resistant zinc coating. Highly conductive, allowing for low-resistance pathways for electrical currents to safely dissipate into the ground. Easy to install and require minimal maintenance. A reliable and cost-effective solution.

  LATH Earthing is the manufacturer, supplier and exporter of Earth Pit Covers. We manufacture it using quality material which is reliable to use. It is used in order to secure Protection for all earthing terminations. It is very light weight, sturdy and portable. It ensures easy access to routine testing of electrical earth.    Earth Pit Cover Salient Features: Earth pit cover are widely used all over the world in different industries. Here are the top features of Earth pit cover – Earth Pit Covers  are made of high grade material. Earth Pit covers  have good chemical resistance and no absorption. Earth Pit Covers  have substantial working load capacity. These are preferred over their concrete  made counterparts for their light weight and simple installation method. These provide trouble free access to earthing electrode. Factory built holes  for accessing strips/wires easily at two side. Green top cap  matches the environment.

LATH Back Fill Compound is a superior conductive material that improves earthing effectiveness, especially in areas of poor conductivity (rocky ground, areas of moisture variation, sandy soils etc.). Tested at  NABL Accredited Laboratory , with 0.02 Ohms-meter resistivity it improves conductivity of the earth electrode and ground contact area. high conductivity. Improves earths absorbing power and humidity retention capability. Non-corrosive in nature having low water solubility but highly hygroscopic. Suitable for installation in dry form or in a slurry form. Does not depend on presence of water to maintain its conductivity. Permanent & maintenance free and in its set form, maintains constant earth resistance with time. – thermally stable between -100 C to +600 C ambient temperatures. Does not require periodic charging treatment nor replacement and maintenance. Suitable for any kind of electrode and all kinds of soils of different resistivity. Does not pollute the soil or local water table and meets environment friendly requirements for landfill. Non explosive and does not cause burns, irritation to eye, skin etc.

• FeatureMaintenance Free Anti-Corrosive High Tensile Low Carbon Steel Inside Tested at CPRI Bangalore & NABL Accredited Laboratory.

LATH Copper Bonded Solid Earth Rods have a core of high tensile low carbon steel with each rod made by molecularly bonding 99.9% Pure Electrolytic Copper. These rods are tested in accordance to  IEC 62561-2  Standard at  NABL  accredited laboratory and  CPRI Bangalore .

• FeatureLarger surface area for current dissipation. Excellent conductivity. Anti-Corrosive Up to 12 years service life. Aesthetic and unique design. Maintenance free. Easy installation at site.
• 50×625×3
• 7650×6
• 40×625×3
• 25×32000
• 1000LE-C4820
• 3000LE-G7610
• LE-G762076
• 2000LE-G7630
• LE-C483048
• LE-C481048
• 4840×6

• FeatureUnmatched Mechanical Strength Anti-Corrosive Higher Current Carrying Capacity Longer Service Life Aesthetic And Unique Design Exceptional Electrical Dissipation Characteristics No Antenna And Beacon Interference 120 Kph Survival Wind Speed.
• Material detailsThe lightning arrestor is 99.9% pure copper bonded on hi-tensile steel in order to enhance the condu
• InstallationThe installation process is super easy, you just need to fit it to the surface of the top point of a
• RoleLightning arrester allows the current to flow the surge current from a clap of thunder to the ground
• CoverageThe copper lightning arrester offers a coverage of 45 degrees from the top point of the arrester.

LATH Copper Conventional Lightning Arrester (Solid Big Size) 17.2 mm diameter and 1000 / 1200 / 1500 mm in length with 5 spikes and base plate 100mm x 100mm for Home and Building Protection. Measurement:  This copper lightning arrester is 1000 / 1200 / 1500 mm long and the diameter of the solid rod is 17.2 mm. The total weight of this product is 2.3 kgs. The dimension of the 3mm Thick base plate is 10*10 cm. 

Blunt tip to strengthen the electric field energy at the tip of the air terminal Stainless steel 316 grade as primary air terminal Sufficient mechanical strength Higher current carrying capacity Excellent corrosion resistance High melting point Long life Secondary Air terminal made of SS 304 grade to capture side flashes occur during lightning event Electro-mechanical device with no external power supply Aesthetic & Unique Design