Mass-tech Controls Pvt. Ltd.

Mulund, Mumbai, Maharashtra

• Brand NameMass-Tech
• Input Voltage24 VDC
• Output Voltage48 VDC
• Output Power500 W
• Galvanic IsolationUpto 2KV
• Output Current10 A

SMPS modules: for Battery Charging & supplying load DC-DC Converter Modules: For Supplying different DC voltages load Inverter Modules: with optional Static bypass switch for supplying single phase or Three phase AC load. Control & Monitoring Unit: for Power Supply Management, Battery Management, Remote Monitoring & Control Through Modems/ Industrial Ethernet. Racks: for mounting Power Supply Modules, Connection of input, Output & Load Distribution. ADVANTAGES Modular System Simple to configure, Flexible , Easy to operate & maintain, Easy to expand. Single Source System With single DC source, one can achieve various DC Voltages using DC-DC Converter Modules & AC Voltages using Inverter modules, in the same system. Cost Effective High efficiencies result in low operating costs & "N+1 Module" concept for redundancy reduces total system cost. Space Saving 70% less in volume & weight compared to the Conventional Systems. High of power density with most compact possible space. Less Down Time Hot swapping of modules without interrupting the over all system. Superior Performance Low starting current, Low ripple (Less than 20mV peak to peak), Better Dynamic Response (Less than 1ms), High power factor. Intelligent System Automatic Malfunction management, Dynamic Load Shedding Management, Remote Controls & monitoring via modems/ Industrial Ethernet.

TYPE AC & DC Distribution Boards MCC & PCC LDB & PDB DG Protection, Synchronising Panels, AMF Panel Metering Panel Custom built Distribution, Instrumentation & Protection Panels FEATURES Single front, Double front, Fixed type, Semi draw-out type, Fully draw-out type, Fully isolated Vertical & Horizontal busbar chamber Fully isolated cable chamber Manufactured out of CRCA sheets Floor mounting, free standing, Vermin & dust proof Powder coated with 7 tank pretreatment Degree of protection upto IP55, Short circuit withstand strength up-to 50KA PLC based AUTOMATION Panels with MMI   Mass-Tech offers PLC based total solution to your Automation needs.The scope covers system engineering, selection of optimum hardware, programming, designing MMI screens and plant specific database, reports generation. In-house trial & site commissioning is also supported. Mass-Tech also offers PLC based systems for DG control and synchronisation, Conveyor systems such as Ash handling system, Building automation including control of AHU, lighting, water treatment units, parking etc. RATING 440V AC, 220V DC upto 5000A, Customize as per requirement

Batteries form the backbone in the operation of a plant performance and dictates the dependability of DC system. In plant, normally batteries of different type viz Lead Acid, SMF or Ni-Cd and of varying AH capacities are used for following applications. APPLICATION AREAS 110 V/ 220V - Switchgear Protection Systems 48V - Communication Systems 380V or above - UPS Systems 24V - Instrumentation & Control Systems, Fire Alarm / Security Systems 24/36/48/72V/80V - Battery Operated Vehicles Availability of DC Supply incase of Power failure or emergency, depends on battery condition/State of Charge. A single weak cell in a battery bank, can lead to failure of total systems resulting in major shutdown. Normally it is very difficult to determine the health/State of Charge of individual cell in a battery bank and also it is not possible with the existing equipment to charge such cells without disturbing / disconnecting the system. MULTI-APPLICATION Battery / cell condition checking On line Charging of sick cell Hot Standby Float Rectifier Battery Re-conditioner for batteries in storage Universal Charger Light Weight and portable: 24V/100A or 48V/50A weighs 5kg only FEATURES On for all Programmable for all types of batteries, different AH capacities & different Voltages Set, Connect & Forget Very simple setting procedure, the total process of charging is Intelligent Microprocessor controlled Safety CE marking, Voltage free output clamps, Output short circuit proof

D.C. Systems comprising of Battery and Battery Chargers upto 500KW Float & boost or float cum boost, constant voltage & constant current, thyristor controlled, upto 500 kW rating, suitable for lead acid, SMF, or Ni-Cd batteries ranging from 20 AH to 5000 AH and 12 V to 220 V or any custom made range. Resistive Load Banks for Battery Discharging Rectifiers (500 kW). TYPE Float charger Float cum Boost charger with voltage dropping diodes/voltage regulator Float and Boost charger Redundant Float or Float cum Boost Charger Tailor made scheme as per customer requirement FEATURES Fully automatic electronic SCR controlled Output short circuit proof Liberal design margins and safety factors Voltage drooping characteristics for Float charger to pass on momentary or short time over loads to battery Soft start feature to minimize inrush current to battery when charger is re-energized Battery Test Function (optional):  With this function, Battery healthiness & battery discharge path can be checked ONLINE. In case there is any problem in battery or discharge path, the float charger shall feed the load which is in "Support mode" without any interruption to the load. This feature helps to ensures the availability of back-up from battery & avoids the uncertainty. Temperature Controlled Charging (optional)  The voltage of battery cell varies with temperature which affects the amount of charge to the battery. Temperature sensor is installed at the Battery bank to measure the ambient temperature of the battery, this measured signal is sent back to the Battery Charger via a feedback loop to adjust the charging voltage accordingly. This feature offer optimum charging of the battery over the operating ambient temperature range Remote signalling for critical faults (optional). RATING 12V, 24V, 48V, 110V, 220V or any custom made up to 500KW suitable for Lead Acid Flooded, SMF (VRLA), Ni-Cd Batteries and Lithium–Ion Batteries APPLICATION For Switchgear Protection Instrumentation power supply Telecom / Infocom Power Plant and Substation Railways Fire Fighting system D.G. set starting

Mass-Tech in association with CONVERTRONIC, Germany introduces MU1000, a control & monitoring unit for DC systems. MU1000 offers complete monitoring of a DC system with unique features like battery management with automatic Battery test, Event history, Remote transmission of system data via telephone/Ethernet. The MU1000C is specially designed for harsh industrial environment. The MU1000C is compact, user friendly, easy to operate from front panel keypads with LCD display 2x16 matrix clear text indication with illumination. The MU1000 can be used in the new DC systems & can also be retrofitted in the existing DC system of any make. DC systems with MU1000 shall have following unique advantages. ADVANTAGES Accurate readings for voltages & current due to digital control Precise setting of monitoring & control values since the set values are digitally set & not by potentiometer Settings are easy from front Keypad Settings are password protected to avoid any unauthorized change Time delay & hysteresis can be set for each alarm Boost Charging of battery manual/automatic operation or from remote control Battery test function with manual & Automatic text according to time Schedule (date , time & interval) Annunciation of error states on front LC display Event History with record for 100 events with time & date All values of DC voltages, current, error states, event history etc. from Remote through RS. 232 port using modem or over industrial Ethernet Monitoring of earth leakage, Battery Symmetry, Control of Voltage dropping diodes

• MaterialMetal,Plastic
• Power SourceButane Gas, Rechargeable Battery
• ColorAvailable in Many Colors
• ApplicationLighting Cigarettes, Candles, Campfires
• FeatureRefillable, Flame Adjustable
• TypeElectric
• Ignition TypePiezo Ignition
• PackagingBox
• Flame TypeAdjustable, Windproof
• Suitable ForOutdoor And Indoor Use

Cathodic Protection (CP) is a method of corrosion control that can be applied to buried and submerged metallic structures. In conjunction with coating, a properly designed and maintained CP will ensure a 100% efficient corrosion Protection System. The Principle of CP is to prevent anodic sites occurring on the structure under protection by allowing anodic reactions to occur on specially designed and installed anodes. The PR is designed to operate is constant current mode and the current is adjustable manually. The PR has various protections like surge protection, fast acting semiconductor fuses, DC overload, DC over voltage, short circuit protection and AC under voltage and also fast acting current limiting which protects the PR from supplying current higher than the set value.

D.C. Systems comprising of Battery and Battery Chargers upto 500KW Float & boost or float cum boost, constant voltage & constant current, thyristor controlled, upto 500 kW rating, suitable for lead acid, SMF, or Ni-Cd batteries ranging from 20 AH to 5000 AH and 12 V to 220 V or any custom made range. Resistive Load Banks for Battery Discharging Rectifiers (500 kW). TYPE