Mitool Make Vibrating feeders are most efficient & economical to convey the bulk materials & in the simplest easiest means of controlling the flow rate.

The Vibrating feeders are extensively used in mines, chemicals, ceramic, Rubber, Pharmaceuticals, clay, Iron & steel Industries, collieries, Quarries of glass industries for handling of all type of materials capacities from 1 Ton to 400 Tones per hour.

Vibrating Feeders are operated by giving pulsating D.C. supply. When this pulsating supply passed through starter creates a series of interrupted pulls on the Armature. 3000 pulse (Vibration) are occurring in one minute.

The Vibrating feeder consists of vibrating trough fitted to the drive unit of considerable weights

The electromagnet unit is mounted inside a heavy housing unit, The power unit which is mounted inside the housing houses the spring bars (Flats) which consisting of a number of leaf springs clamped at the two ends of the power unit.

A heavy fabricated centre piece carries the magnet armature at one end & vib feeder trough at other end. The centre clamp tightens at the middle of the spring bar system .
Stiffeners & gussets are provided to make the trough rigid. Our Feeders Protects the belt conveyors from damage by feeding the material on to the belt conveyors from storage hoppers, silos, surge hoppers & dumpers at the controlled rate. In magnetic feeders there are no wearing mechanical parts, such as gears, cams, belt, bearing, eccentrics weights or motors.

Mitool Vibratory feeders are most economical equipments.

Vibrator motors are robust, highly stable under load, having cylindrical roller Bearings
Vibration resistant, high quality resin impregnated windings. End Shield fitted
with rubber 0 rings to give dust tight and watertight enclosure. Quite running and require no maintenance.

Robustterminalboard, cablewirecastinvibrationresistantsyntheticresin.Reliablehigh
torquestarting, Absolutelysecurefixingofourofbalanceweightsonlytheinnerweightsare
adjustable, withlegiblemarkingsontheweights.

HIGH BAY LUMINARIES WITH MERCURY SODIUM VAPOUR LAMPS ARE EXTENSIVELY USED IN STEEL PLANTS. POWER PLANTS AND HEAVY ENGINEERING INDSUTRIES WHERE THESE LUMINAIRES ARE SUBJECTED TO SEVERE VIBRATION AND SHOCK ROUND THE CLOCK, DUE TO THE TRAVELING OF BUSY OVERHEAD CRANES MOVING IN PLANTS.

THE NORMAL GUARANTEED DURATION OF A LAMP IS THUS SEVERELY AFFECTED AND DUE TO WHICH WITHIN A SHORT PERIOD IT GETS FUSED AND THEN REPLACEMENT OF LAMPS AT A HIGH BAY ROOF TRUSS BECOMES A HAZARDOUS JOB.

TO INSTALL A DAMPER (JUST SUSPEND THE LUMINAIRE FROM THE DAMPER) WHICH WOULD PROTECT THE COSTLY LAMPS FORM THE PREMATURE FAILURE DUE TO VIBRATION AND HEAVY SHOCKS, THUS SUBSTANTIALLY SAVING ON COST OF THE LAMP, AND WHICH ALSO SAVES LABOUR AND DOWN TIME BEACAUSE OF DAMPER.

SO, FROM THE ECONCOMICAL POINT OF VIEW THE HIGH BAY DAMPERS ARE INDISPENABLE FOR HIGH BAY LUMINAIRES TO SAVE VERY COSTLY LAMPS FIXED ON IT.

APPLICATION
SUIABLE FOR MELTING SHOP, BLOOMING, SLABBING, ROLLING AND SHEET MILL, HEAVY ENGINEERING SHOP ETC.

"MITOOL" make resistance boxes are designed to meet requirements of both A.C. & D.C. application. For E.O.T. Cranes, Winches, Rubber Mills, Steel Mills, Cement Mills, Power Plants, Conveyors, Coke Oven, Blowers etc., resistance boxes can be of following types :

* Stainless Steel Grid Resistors
These resistors consists of stainless steel wire or strip in form of grids

* Punched Steel Grid Resistors
These resistors consists of grid punched from stainless steel / fecral sheet and are available in wide range from 7 amps to 1500 amps continuous rating