MTS Incorporation  supplies a quality line of high pressure Integral / Fabricated Union connections with Unions in various configurations and sizes from 2" to 4" and in pressure ratings upto 20, 000 PSI CWP. These items are manufactured from high strength alloy steel forgings and fully heat treated under controlled conditions to assure uniform quality throughout. Available in combinations Male by Male, Male by Female to suit virtually any installation. The type of connections that MTS supplies  are - Crosses, Elbows, T's & Y's. 45º and 60º laterals Crows foot Goat Head.  

Friction surface material is Chrome leather. Back surface material is Black coated Fabric. The belt factor is 5 N/mm at 1% elongation for product code MTS 50LT, 7.50 N/mm for MTS 75LT, 10 N/mm for MTS 100LT, 15 N/mm for MTS 200LT,   23 N/mm for MTS 300LT, 30.50 N/mm for MTS 400LT.

Friction surface material is NBR film. Back surface material is NBR film. The belt factor is 2 N/mm at 1% elongation for product code MTS 20F, 4 N/mm for MTS 40F, 6.50 N/mm for MTS 80F.

MTS V-BELTS  ARE MANUFACTURED UNDER STRICT VIGILANCE AND OBSERVATION OF THE STATE OF ART OF MODERN TECHNOLOGY WITH REINFORCEMENT OF HIGHLY SHOCK - LOAD RESISTANT SYNTHETIC CORDS COMBINED WITH SPECIAL RUBBER COMPOUND AND ULTIMATELY JACKETED TO OBTAIN MAXIMUM LlFE AND SMOOTH RUN OF THE DRIVE. .  Cover... The bias-cut cover fabric is impregnated with special rubber to protect the inner part of the belts and provide strong abrasion resistance on the pulley groove. B.  Tension Member... The load carrying cords are tough polyester / aramide cords that have been specially treated to temper the cords to their point of high strength, low elongation and greater resistance to bending fatigue. C.  Top Compression Section... The rubber used in this section is compounded to withstand sudden shock loads and to keep the belt flexing readily when passing over the pulleys. D.  Insulation Section... The insulation section holds the tension binding section for extra strong adhesion between cords and the top and bottom compression section. E.  Bottom Compression Selection... This section holds the normal cross section of the belts and is compounded to resist compression fatigue and heat for longer service life.

Friction surface material is Chrome leather. Back surface material is Chrome leather. The belt factor is 5 N/mm at 1% elongation for product code MTS 50LL, 7.50 N/mm for MTS 75LL, 10 N/mm for MTS 100LL, 15 N/mm for MTS 200LL,   23 N/mm for MTS 300LL, 30.50 N/mm for MTS 400LL.

Friction surface material is NBR film. Back surface material is Texture. The minimum pulley diameter at 20 deg. C is 15mm for product code MTS S-0 and 15mm for MTS S-1. The belt factor is 1.25 N/mm at 1% elongation for product code MTS S-0 and 2 N/mm for MTS S-1.

Friction surface material is NBR elastomer. Back surface material is NBR elastomer. For MTS 50R 12, 1.20mm thickness belt, friction surface material is NBR elastomer and back surface material is NBR film. The belt is having Anti-static properties. The minimum pulley diameter at 20 deg. C is 25mm for product code MTS 50R , 40mm for MTS 75R, 60mm for MTS 100R, 110mm for MTS 200R. The belt factor is 5 N/mm at 1% elongation for product code MTS 50R, 7.50 N/mm for MTS 75R, 10 N/mm for MTS 100R, 15 N/mm for MTS 200R.

NYLON SANDWICH BELTING  These belts are ideally suited for various applications such as :- TEXTILE WOLLEN KNITTING WOODEN PAPER MARBLE GRANITE INDUSTRIES AS WELL AS ANY KIND OF  ENGINGEERING INDUSTRIES. OUR PRODUCTS :- RUBBER NYLON SANDWICH BELTS. LEATHER NYLON SANDWICH BELTS. LEATHER NYLON FABRIC BELTS. FABRIC NYLON FABRIC BELTS. SYNTHETIC SPINDLE TAPE. CONDENSOR TAPE. COMBING LEATHER. KNITTING MACHINE BELTS. Nylon Sandwich Belt Product Description:- This product comes under the category of Power transmission industry. As the name indicates, ‘Nylon’ is used as sandwich. This product runs on ‘Plain Pulley’ whereas V-Belts runs on ‘Grooved Pulley’ which means in any textile/paper industry where V-Belt is used, there is requirement of this product. Nylon is used as sandwich in this product as in today’s world, nylon has maximum strength, controlled Elongation, more durability as well as life. ‘Rubber-Nylon-Rubber’ category is used in any type of textile industries in various machines under different drives as well as in any kind of Engineering Industries. ‘Leather-Nylon-Leather’ category is used in any type of paper, textile, wooden, marble industries and certain other industries where oil/lubricants spillage exists as leather has all the properties to absorb oil as well as in any kind of Engineering Industries. Both the above mentioned categories are having requirements in certain widths like 50/100/150/200/250/300 mm etc. and in open lengths in rolls of 50, 100 metres. We can manufacture this product in maximum width of 300 mm and in rolls of 50, 100 metres & above. We manufacture both the above mentioned categories in high quality, most competitive prices and on the top at par with World class manufacturers like Habasit, Nitta etc. Advantages and Special Features of MTS Flat Belts :- Extensively High Tensile Strength. No permanent Elongation. High Efficiency. Steady overall thickness. Light weight, reduce bearing loads. High co-efficient of friction. Wide Range of Power Transmission from 0.5 HP to 200 HP.

TS  Tongs   are reputed for  toughness, dependability and ease of handling. Virtually every piece is manufactured as per API specification. Numerically controlled and automatic machine tools handle almost every step of machining to assure a proper fit between working parts. MTS Tong   is an effective tool for casing and tubing operations, it has been designed for toughness, dependability and ease of handling. These Tongs are available in a variety of models, sizes and types to handle almost any down hole pipe string, as well as rods.  From 4-1/2" Tubing Tong to 20" Casing Tong Hydra shift and Hydro shift, tubing and casing tongs, available in variety of models, sizes and types, to handle casings, drill collars, tubing as well as sucker rods.   TONG Dies   are available on specific request.

Width: 300 mm to 1800 mm in steps of 50 mm.   Length : Open or endless upto 200 mtrs in single length   Fabrics plies : 2 plies to 8 plies  Fabrics : Polyster Nylon (EP) EP 100, EP 125, EP 150, EP 200, EP 250, EP 300, EP 350 , EP 400 and EP 450  Nylon Nylon (NN) NN 100, NN 125, NN 150, NN 200, NN 250, NN 300, NN 350, NN 400 and NN 450.   Cotton Cotton 28 OZ, 32 OZ, 36 OZ, 42 OZ, 48 OZ and for elevator belts 34 OZ. X  Mechanical Fasteners not recommended. For Specific requirements not covered in above table, please contact with details. The figures  mentioned above are approximate values for consideration for drive design. and are subjected to change without notice in the make of fresh developments.  Cover Grades  : Cover type  Tensile strength  Elongation at break  General Applications  Specific. Kg/cm2 (Min.) (% Min.) M-24 240 450 Suitable for rugged services for conveying crushed Metallic ores, Lime stone, Granite etc. Also suitable for large size ores.  IS-1891, (Part-I)-1994  N-17  170  400 Suitable for Materials, like Asbestos, Ash, Bauxite, Cement lime etc. IS-1891, (Part-1)-1994  HR(T1) 125 350  Suitable for Transporting hot material (Upto 125oC for coarse material and 100oC for fine material)  IS-1891, (Part 2)  SHR(T2) 125 350 Suitable for transporting hot material (Upto 150oC for coarse material and 125oC for fine material)  IS-1891, (Part 2)  OR (Oil Resistant)  120 250 Cover Grade of specially blended synthetic Polymers is designed to give very high resistance to mineral vegetables and Animal Oils & Fats.  IS-1891, (Part 3)  FR (Fire Resistant)  170 350 Recommended for use in surface applications in coal and such type of mines where the ambient temp. may not be high but there is distinct hazard of belts being enveloped in fire. Rubber covers are fire resistant and anti static.  CAN/CSA/ M-422/ M-87 & IS-1891 (Part 5) Covers thickness  : 1mm to 12mm in steps of 0.5 mm  Type of Edges : Available in cut edges and moulded (protected) edges.    Skim coated : The belts are processed with its all fabric plies skim coated with superior quality rubber compounds  Mildew inhibition : The rubber compounds used in the belts are designed such as to have full protection against mildew  Breaker Ply: To with stand extra impact during service the belts are provided with breaker ply on demand.   Belt Designation: Available in three types i.e. General Duty (GD), Heavy Duty (HD) and Extra Heavy Duty (EHD). Apart from straight ply construction the belts are offered in Stepped ply as well as Reverse stepped ply constructions also.   National and International Standards followed  : 1. Bureau of Indian Standards BIS  2. British Standards  BS  3. International Organisation for Standardization  ISO  4. German Standards  DIN  5. Canadian Standards  CBM  6. Australian Standards  ASS  7. France Standards  NF-T47-100/101   Special features of MTS Conveyor Belts : 1. Unique Carcass Design & Assembly.  2. Superior Adhesion Levels.  3. Higher Longitudinal Flexibility.  4. Improved Transverse Flexibility.  5. Higher Tensile Strength.  6. Low Belt Stretch.  7. Outstanding Impact Resistance.  8. Improved resistance to mechanical damages.  9. Higher carrying capacity with low belt weight.  10. Rot Resistance.  11. Hot & cold splice proven.  12 Superior joint efficiency & increased life.  13. Universal applications. 14 Resistance to environmental operating condition. 15. Smooth & trouble free service.      

Treating Irons - MTS one piece Treating Iron comprises an integral MTS wing union end connection which eliminates welds and threads. Available in length upto 12 feet. Material is of Carbon Steel and alloy steel and is light weight. This integral treating iron is capable of handling a variety of fluids at cold working pressure of 15000 PSI. MTS treating irons are also available for sour service upto a CWP of 10, 000 PSI & in other lengths if required. Recommended Service - These are suitable for High Pressure Discharge Lines, temporary Flow Lines, Auxiliary Flow Lines, Well Testing Lines, Water Lines, Choke and Kill Lines and Abrasive Applications. Salient Benefits - Since there are no welds and threads, MTS treating Irons provide an uniform bore of greater flow capacity and improved flow characteristics. MTS design allows for uniform heat treating of the entire joint for better structural qualities. Nut can be detached for easy disassembly if replacement becomes necessary. For this only a circlip has to be removed. End Connections -   End connections can be provided for customer choices.