Products / Services
  • Products / Services
  • Companies
  • Buy Leads
Post Buy Requirement

Can Side Seam Welding Machine

Listing ID #4207603

  • Welding speed10 to 15 mtrs/minutes
  • MODELSSW-01
  • Floor area required2900 x 3400 mm.
  • Rating@50% duty cycle15 KVA
  • Machine dimension (Excluding arms)1000 x 2150 x 1800 mm.
  • Supply Type Manufacturer, Exporter, Supplier
Preferred Buyer From : All over the world
View More Details
Send Enquiry
  • Member Since 7 Years
  • Nature of Business Retailer

Ask for more detail from the seller

Contact Supplier

Product Details no_img_icon

This machine is for welding tin sheet, black sheet with thickness of 0.2 to 0.5mm and body diameter from 52 to 300 mm. and max.height upto 450 mm depending on arm size.

Nospark Engineering Container Side Seam Welding Machine model SSW-01 is a trustworthy and economic way of producing consistent, faultless weld at highest working speeds.

Weldability :

The machine is capable of welding a wide range of materials, Tin sheets, Black and TFS sheets (after proper edge cleaning) with thickness ranging from 0.2 to 0.4 mm and body diameters ranging from 52 to 300 mm and body height up to 450 mm.

Intermediate Electrode :

Use of electrolytic copper wire as an intermediate electrode between weld wheel and tin sheet, avoids deposition of molten tin on weld wheels and ensures consistent, quality weld without frequent cleaning of weld wheels.

Welding Upper Arm :

Upper arm made out of high tensile brass is common for complete range of can diameters and is operated by a hydro-pneumatic damping cylinder to avoid initial impact on weld wheels and to maintain constant welding force.

Welding Lower Arm :

Lower arm made out of high tensile brass is complete with carriage guide rail, Z-bar, weld wheel etc. Three standard sizes of lower arms are available. Any one size of arm will be provided with machine, other sizes will be available at extra cost.

Weld wheels & Z-bars :

Antifriction, mercury contact weld wheels made out of special copper alloy & Z-bars made out of wear resistant material are available in three standard sizes i.e. 52, 65 and 100 size suitable for respective arms. These wears out parts are available as spares. Standard overlap provided on Z-bar is 4 mm.

Carriage :

Carriage assembly with built-in pneumatic clamping and limit switches for low/high current initiation and auto cut off is mounted on antifriction bearings and can be adjusted for different can lengths easily. Different sizes of carriages are available to match each size of arm. Movement of carriage is actuated by automatic fly-start system to maintain normal welding speed from the start.

Electronic Control :

High precision fully solid state welder control incorporating thyristors permits uniform weld quality. Two-stage heat control unit controls the intensity of weld current at the beginning of weld cycle at desired low levels. Current control is through transformer taps and potentiometers.

Operation and work cycle :

Once the welding parameters like current, pressure, speed, carriage positioning, high /low heat and cut-off limit switch setting is over, operator must feed a pre-rolled sheet into the carriage and Z-bar.

On operating foot switches all further operations take place automatically.

  • Rolled body is clamped at the rear with pneumatic clamps.
  • Upper weld wheel comes down making contact with lower weld wheel and welding pressure is developed between wheels by hydro-pneumatic damping cylinder and spring.
  • Once the correct welding force is generated, the switch fitted on cylinder actuates wire feed system.
  • The carriage is pushed forward at the start of operation by means of fly-start mechanism.
  • Initially reduced current is applied for a pre-determined length and thereafter-full welding current is provided. The weld initiation with reduced current and change over to full current is done automatically by weld controller.
  • At the end of weld, the current is cut-off, wire, feed system stops and upper weld wheel goes up automatically.
  • The work piece can be taken out after de-clamped and carriage is pulled back by spring balancer making machine ready for next work piece.


Compressed air Minimum pressure 5.6 kg./sq.cm.
Cooling water 20 LPM@3kg./sq.cm. pressure and 18 degree C for welding arm cooling.

10 LPM @ 3kg./sq.cm. pressure and 30 degree C for transformer and Thyrister  cooling.
Supply 3 phase,415 V,50 Hz.
Main switch/fuse 30/20 Amps.
Supply cable cu./al. 10/16 sq.mm.

 

Size 1 2 3
Can diameter range(mm) 100-300 65-100 52-65
Max. can length(mm) 450 325 200


Tell us your Buy Requirement to Get Instant Response
Tell us what you need?

Looking for Can Side Seam Welding Machine?

Quantity
Seller Contact Details
  • Seller Nospark Engineering
  • Address Airoli, Navi Mumbai, Maharashtra
Waiting for permission
To search by voice, go to your browser settings and allow access to microphone

Allow microphone access to search with voice