Write a Review
Our Products
Our offered Product range includes Cable Ties, Speciality PCB Ejector, Micro Support Post, Tear Drop Board Supports and PCB Ejector.
They are designed for use with most standard sheet metal card cage systems and can be used with virtually all major card support systems. It is attached by means of rivets to cards of 1.6 mm thickness and operate by lever action against card guide or mounting bar-providing both easy insertion & removal .
It is designed to provide permanent locking for chassis. For modification or service the PCB can be pulled out easily by just pinching the head with finger or simple plier. Snap into 3.2 mm dia hole of 1.6 mm thick chassis & PCB. Available in spacing height 11.1 mm.
Teardrop style nose simplifies insertion and provides increased holding power. Snap into 2.5 mm dia hole of up to 1.6 mm thick board.
| Novoflex Part No. |
Spacing Height (mm) |
Dia Hole (mm) |
Standard Packing |
| PSTE 79 | 7.9 | 2.5 | 100 Nos. |
They are designed for use with most standard sheet metal card cage systems and can be used with virtually all major card support systems. It is attached by means of rivets to cards of 1.6 mm thickness and operate by lever action against card guide or mounting bar-providing both easy removal & insertion.
| Novoflex Part No. |
Mounting Method |
PCB Hole Size (mm) |
PCB Thickness (mm) |
Standard Packing |
| CBE 3 | Snap Type | 2.8 | 1.6 | 100 Nos. |
Designed to allow close mounting of PCB as is required in high density packaging. Snaps into two 3.2 dia pre-drilled holes, 1.6 mm thick PCB without the aid of pins or rivets. Curved tab provides fingertip grip for board insertion and removal.
A one piece non-conductive, fool proof holding device for fixing of Can Type Aluminum electrolytic capacitor which can be fitted easily and quickly. Application- just position it on the Capacitor and press the jaws togther. For maximum tightness a plier can be used to give that firmness and vibration resistance.The capacitor Holder can be released and reused again and again.
| Novoflex Part No. |
To Hold Cable Dia | Panel Hole Dia |
Plate thickness |
Standard Packing |
|
| Max. | Min. | ||||
| PSC 30 | 30 mm | 24 mm | 6.4 mm | 0.6-2.0 mm | 100 Nos. |
Novoflex Adhesive Backed Tie Mounts are used to anchor wire bundles or cables to walls, ceilings, plates, panels, or any other structure. No tool is required for installation. Simply place the Adhesive-Backed Mount on the desired surface, and secure the cables with Cable-Ties.
The Continuous-Straight Pull Load is 1Kg/square inch (25.4mm) of adhesive. Operating Temperature for Adhesive: Upto 52C
| Novoflex Part No. |
Size L X B X H (mm) |
Mounting Method |
For Max. Cable Tie Width “W” (mm) |
Standard Packing |
| TC1 (A) | 28x28x6.2 | Adhesive Foam Tape | 5.5 | 100 nos. |
| TC2 (A) | 19x19x7.1 | Adhesive Foam Tape | 4.0 | 100 nos. |
| TC12 (A) | 130x130x5.5 | Adhesive Foam Tape | 2.5 | 100 nos. |
| TC40 (A) | 40x40x8.2 | Adhesive Foam Tape | 9.5 | 100 nos. |
Novoflex Screw Type Tie Mounts are used to anchor wire bundles or cables to walls, ceilings, plates, panels, or any other structure. The Saddle Design provides Maximum Stability to wire bundles. To apply, simply fix the Mount to the desired surface with a screw, and secure wire bundles with Cable Ties.
| Novoflex Part No. |
Size (mm) |
Mounting Method (mm) |
For Max. Cable Tie Width (mm) |
Standard Packing |
| TC1 (S) | 28x28x5.2 | 5 mm Screw | 5.5 | 100 nos. |
| TC2 (S) | 19x19x6.1 | 4 mm Screw | 5.5 | 100 nos. |
| TC3 (S) | 13x12x7.2 | 3 mm Screw | 8.5 | 100 nos. |
| TC4 (S) | 22.5x16x9.8 | 6 mm Screw | 8.5 | 100 nos. |
| TC5 (S) | 15x9.4x6.8 | 3 mm Screw | 5 | 100 nos. |
| TC6 (S) | 17.8x12.7x8.20 | 4 mm Screw | 5 | 100 nos. |
| TC40 (S) | 40x40x7.2 | 6.4 mm Screw | 9.5 | 100 nos. |
Use these cable tie mounts to anchor wire bundles or cables to walls, ceilings, desks or any other structure. To use simply push the head of the mount through the hole, fastening the mount there. Then pass the cable tie through the slot provided at the base of the mount.
| Novoflex Part No. |
Size H X W (mm) |
Mounting Method (mm) |
For Max. Cable Tie Width "T" (mm) |
Suitable For Plate Thickness |
| TC 7 (P) | 20x20.5 | Push Mount in 6.4 mm hole Dia | 8.0 | 1.8 - 2.3 mm |
| TC 9 (P) | 25.8x20.5 | Push Mount in 9 mm hole Dia | 8.0 | 8 - 11 mm |
They provide a new convenience in initial assembly of wires, plus versatility for easy inspection, removal, repair or changing of wires. Wire bundles are secured in moments with a fingertip twist. These clips cut costs by speeding assembly. Available in 5 standard sizes covering cable bundle diameter ranging from 4.0 to 20.3 mm.
| Novoflex Part No. |
Bundle Diameter Range | Standard Packing |
| KK-00 | 12.0mm - 15.0mm | 100 Nos. |
| KK-0 | 17.8mm - 20.3mm | 100 Nos. |
| KK-1 | 10.0mm - 12.7mm | 100 Nos. |
| KK-2 | 7.6mm - 10.0mm | 100 Nos. |
| KK-3 | 4.0mm - 7.5mm | 100 Nos. |
Designed to lift wires off board to avoid hot components and minimize transient interference. Cable & wire bundles can be secured simply by a fingertip twist. The main feature of these clips is that they can be installed easily & quickly by just pushing into a predrilled hole in PCB frame, chassis, sidewall electronic / electrical equipment in moments. Available in 6 standard sizes.
| Novoflex Part No. |
Dimension in mm | Hole Dia (mm) |
Standard Packing |
|||
| A | B | C | D | |||
| SKP-1 | 24 | 4.4 | 10 | 10 | 4.76 | 100 nos. |
| SKP-2 | 27 | 18 | 12 | 10 | 4.76 | 100 nos. |
| SKP-3 | 18 | 31.5 | 5.5 | 10 | 4.76 | 100 nos. |
| SKP-6 | 30 | 68 | 11 | 12 | 4.76 | 100 nos. |
| SKP-9 | 30 | 2.5 | 15 | 12 | 4.76 | 100 nos. |
| SKP-10 | 38 | 13 | 19 | 11 | 6.40 | 100 nos. |
It is designed for routing wires to any direction. Simply twist to open and close for wiring change and repairs. It is mounted securely with a single screw.
| Novoflex Part No. |
Dimensions | Standard Packing |
||
| A (mm) | B (mm) | C (mm) | ||
| SKS - 4 | 8.3 | 10.2 | 36.8 | 100 nos. |
Designed to lift wires off board to avoid hot components and minimize transient interference. Cable & wire bundles can be secured simply by a fingertip twist. Arrowhead design snap locks into a 4.8 mm diameter hole. Hinged design eases installation in otherwise hard to reach places.
| Novoflex Part No. |
Hole Diameter (mm) |
Standard Packing |
| SKH 7 | 4.8 | 100 Nos. |
Features:
Application:
| PILFER PROOF SEALS | ||
| Part No. | Length | Width |
| CP - 380 ES | 380 | 7.6 |
| CPS - 368 ES | 368 | 4.7 |
| CPS - 300 ES | 300 | 4.7 |
| CP - 300 ES | 300 | 7.6 |
| CP - 250 ES | 250 | 4.7 |
| CP - 200 ES | 200 | 4.7 |
| CPS - 200 ES | 200 | 3.5 |
| CP - 160 ES | 160 | 4.7 |
| CPS - 160 ES | 160 | 2.5 |
| CPS - 150 ES | 150 | 3.5 |
| CPS - 100 ES | 150 | 2.5 |
| Reusable Identification Seals | ||
| Part No. | Length | Width |
| CPU - 150 | 150 | 7.5 |
| CPU - 200 | 200 | 7.5 |
| CPU - 300 | 300 | 7.5 |
| Identification Pilfer Proof Seals | ||
| Part No. | Length | Width |
| CPI - 100 | 100 | 2.5 |
| CPI - 200 | 200 | 4.8 |
| Identification Pilfer Proof Seals | ||
| Part No. | Length | Width |
| CPI - 100 | 100 | 2.5 |
| CPI - 200 | 200 | 4.8 |
| CUSTOMISATION | ||
| Standard Colour |
Others Colours |
Name / Logo (Printing) |
| Natural white | Red,Yellow, Blue, Green, Black √ Min. Qty. 5000 Nos |
√ Min. Qty. 5000 Nos |
Used primarily for light duty fastening of screws in concrete, brick, dry wall, hollow brick, wooden structure, natural stone plates.
Quick & secure tool for fixing screws.
How to use:
| Novoflex Part No. |
L mm |
D mm |
d mm |
Standard Packing |
| EP - 6 | 31 | 6 | 4.8 | 100 Nos. |
| EP - 8 | 40 | 8 | 6.0 | 100 Nos. |
| EP - 10 | 45 | 10 | 7.5 | 100 Nos. |
| EP - 12 | 48 | 12 | 6.5 | 100 Nos. |
Bumper feet are attached to wide variety of appliances and table top products to protect surfaces and give added manoeuverability. They do not skid or scratch and offer a high degree of protection for both product and location. They are fixed by means of screw or bolt-nuts or rivets.
Mr. Dinesh Kumar Banka (Novoflex Marketing Pvt. Ltd.)
'Raikva' - 5th Floor, Unit-6 3A, Ram Mohan Mullick Garden Lane, Beleghata, Kolkata, West Bengal - 700010, India
Share us via
