Other Products / Services #3263570

The SilicoCon Drymix is a kiln dried, pre-blended, factory-produced prescribed concrete mix, incorporating standardised binders, Graded sand and aggregates, with a guaranteed cement content and mix proportions.

 

SilicoCon Concrete Mix is a general purpose Bag Drymix concrete, it is is a kiln dried, pre-blended, factory-produced prescribed concrete mix, incorporating standardised binders, Graded sand and aggregates, with a guaranteed cement content and mix proportions.

 

It is suitable for concrete bases, mortar beds, Pouring Slabs, shed floors, post erection, walkways, steps, fill deep holes, general repair work and other non-structural applications.

 

SilicoCon is manufactured by M/s Precise Conchem Pvt. Ltd., at their plant located at GIDC Panoli, Bharuch District of Gujarat in an automated process according to formulations based on various products studies and research undertaken. The plant is one of the most modern Plants in India, in which all the critical manufacturing processes and operations are completely controlled by P.L.0 SYSTEMS (Programmed Logic Controller)

 

Features &  Benefits:

• Consists of a carefully proportioned blend of high quality materials including rounded river run sands and aggregates, Portland cement and special concrete admixtures.
• The performance and convenience makes it particularly suited for concrete jobs around
• Achieves a 28-day compressive strength as per requirements.

 

Advantages Of Dry Pack Mortar:

• Used for Interior and Exterior applications
• Uniform and consistent quality
• Jobsite mixing of sand and cement is no longer needed
• It can be tamped, compacted and filled easily
• It guarantees a consistent mix on large jobs
• Ensures Less Wastage and saves time

 

Benefits:

• Reduced paint consumption
• Superb White Finishing
• Saves time
• Cost effective

 

Mixing Instructions

The contents of the bag can be mechanically mixed in a free fall mixer for 3-4 minutes or hand mixed by pouring the contents of the bag onto a clean flat surface and slowly adding clean water in increments and mixing continuously, until the desired workability is achieved. For optimum results, approximately 9 to 10% of clean water should be used per bag. The concrete should be used within 60 minutes of water addition.

 

Refrain from excessive water addition as this will weaken the mix, delay setting times and adversely affect durability. There is no need to add further additives or admixtures to the material on site as all required plasticizers and workability aids are already incorporated into the mix.

 

For optimum results, the concrete should be cured for at least seven days after laying by covering with plastic sheeting or another suitable material. Similar measures should be taken where appropriate to protect the concrete from the effects of the sun, wind, rain and frost.

Advantages:

• Ready to use and only onsite mixing with water is required
• Better Bond then conventional cement based mortar
• Can be used for both interior & external applications
• Excellent adhesion and slip resistance
• Quick curing and floor can be used after 24 hrs
• Shrinkage cracks are minimized due to its water retaining and self-curing properties

 

How to Use:

• Ensure that old tiles are perfectly joint and having uniform level. If any hollow space is present same should be filled by the mortar
• Tiles should be rinse with water to remove dust & loose particles
• Take Silico Tile FixWall & Floor Tile Adhesive in a mixing tub, add approx. 5-6 Litres water to make lump free mortar consistency (Adhesive: - water mixing ratio 3:1 by volume)
• Wait for 4 minutes and then mix it with the help of a trowel
• Apply mix material on the surface at 3-5 mm thickness, spread it with the help of notched trowel, do not spread in more than 1sq m of area at a time. Press the tile firmly, hammer gently with soft mallet to ensure perfect bond
• Clean the excessive adhesive from the joints
• Leave the tile applied area untouched for 24 hrs
• Clean the tools & equipment’s with potable water immediately after use

 

Precautions and Limitations

• Heavy tiles must be supported by mechanical clamps while fixing on the vertical surface
• Always add powder to water and not water to powder
• Do not add more water than recommended
• Do not add sand or cement at site
• Before doing tile-on-tile application, ensure that the original tiling surface in sound condition.
• Strictlynotrecommendedforthedirectuseongypsumplaster, paint, wood, Plastic Substrates & Metal.Consult Technical Dept or CC  Division of Precise Conchem PvtLtd

SILICO Crete TRG is a high-performance Gun Grade Premixed Mortar designed for effective filling of Tie-Rod holes and Wall Tie opening of shuttering technology. The product is designed to flow and travel and yet remain cohesive when filled by hand or by machine while being filled into the tie-rod hole so that the entire mix is filled inside hole without excessive oozing out from the other end. SILICO Crete TRG meets the requirements of GreenPro Ecolabel and qualifies as Green Product. 

 

Benefits:

• Single pack system with just the addition of water
• Flows yet remains cohesive for effective filling of Tie-Rod Openings
• Drying Shrinkage Compensated
• Plastic Shrinkage Controlled with Fiber Reinforced
• Early Strength gain
• Good Bond to Base Concrete
• Sufficient Paste to get comparable surface finishing matching surrounding Concrete
• Sufficient Cohesiveness to enable using Small Pumps for faster turnaround of filling work.

 

Method of Application:

• Clean the Tie Rod/wall tie holes/gap / opening to be filled and remove loose unsound concrete particles, dust, oil, paint, grease, waterproof coating etc. from the entire hole/gap and gap/hole should be free of all contamination which hinders adhesion
• 2Saturate the substrate with water to prevent absorption of water from the mixed material by flushing water inside the holes to be filled.
• 3Add around 80% to 85% of the predefined amount of water in the mixing vessel to SILICOcrete TRG powder slowly under continuous mixing. Preferably use a slow speed mixer. Keep mixing for 2 minutes. Add balance quantity of 15%-20% of mixing water and again mix for another 2-3 minutes to form homogeneous, uniform consistent workable mix.
• 4Now fill the Cement Mortar Caulking/Grouting Gun with the above prepared Silicocrete TRG workable mix fully and use a suitable Nozzle provided with the Gun which will exactly be compatible Tie Rod opening.
• Start filling the Tie Rod/Wall Tie holes with the above workable mix of SILICOcrete TRG from one end by applying required pressure using Cement Mortar Caulking/Grouting Gun till the mix travels smoothly throughout the hole by filling entire space in the hole and is seen reaching the other end of the hole without excessive ooze-out from the other end.
• Now remove the Gun from the first end and finish both the ends perfectly using flat thapi so that both the ends are level in line with the parent surface.
• The above same procedure should be followed for filling all other Tie Rod / Wall Tie holes.
• The Silicocrete TRG Mix should be used within the prescribed pot life.

silicobond is a modified polymer emulsion specifically designed for cement based applications

advantages:

• excellent bonding: the bonding strength between old concrete & fresh mortar will be distinctively improved. excellent adhesion to concrete, masonry, brick, wood, metals etc.
• higher strengths:flexural & impact strength is increased compared to the unmodified mix lower.
• permeability:water absorptions is reduced, therefore providing excellent water proofing capabilities.
• better resistance: increases resistance to industrial chemicals. uv light and heat as well as improved abrasion resistance.
• lower shrinkage:modified mortar is plasticised considerably. mortars with low water, cement ratio can be achieved without affecting workability and therefore.
• enhanced curing: the modified mortar has better water retention capability and holds the mix water in mortar for enhanced curing.
• improves surface hardening: limits wear & dust production of concrete.
• safe to use:being water-based it is eco-friendly in nature & is easy to handle.

uses:

• bonding coat:as a bonding coat between old concrete & new mortar/concrete.
• passivating coat:anti corrosive /passivative treatment to reinforcement and concrete surface.
• concrete repair & adhesive mortar by polymer modified mortar: for repairing spalled concrete floors, beams, columns, slabs, foundations.
• wear resistant mortars for floors: abrasion resistant, crack resistant polymer mortars on industrial
• repairing floors & stairs: as a patch-up polymer mortar for filling up voids, loose pockets, spalled edges etc.
• crack sealing: can be used as a crack filling compound by mixing with cement and cement injection mixing for grouting purposes.
• renderings & coatings: cement based renderings especially in tanks, water treatment plants, etc. for improving the water impermeability also for renderings on foundation.

application guidelines:

• surface preparation: the concrete surfaces and the reinforcing steel should be clean, free from dust, dirt, loose particles, grease oil etc. when repairing, the base concrete must be sound and firm.
• preparation of bonding coat: the prepared bases, such as concrete, bricks, stones etc. should coat consisting of one part silicobond to two part portland cement, mixed homogenously.
• preparation of polymer modified mortar: to prepare silicobond modified cement mortar, premix thoroughly solid components viz, portland cement, sand in required proposition pour silicobond at a ratio of 20% of cement weight with required quantity of water to mixture, and mix thoroughly for about 3 to 4 minutes. finally add the water little by little, until the required consistency achieved.

It's reducing your construction's impact on an environment as much as possible, while maintaining economy, comfort and durability. Advantages Manufacturing Process emits no pollutants or creates toxic waste products.Manufactured from common, abundant materials.Reducing energy Consumption in production.Excellent thermal efficiency reduces time for space heating / cooling in buildings, saving precious energy.Easy workability, all ones accurate cutting, minimizing solid waste during use.

At present concrete block is very successfully being used in construction industries, as because - Easy & Speedier and convenient execution of construction work.More Strength, and less weight.Heat and sound proof.Considerable saving in cement mortar for masonry and plastering.Perfect shape & size for perfect work