Oil And Lubricants #385433

Engine Flush is a specially formulated combination of additives and carrier fluid. In combination with the carrier fluid, the highly effective detergent and dispersant additives dissolve sludge and lacquer formers. All types of oil-soluble and oil insoluble residues are brought into suspension and removed during the next oil change. An engine which has been cleaned of deposits and contamination and which is then filled with fresh oil not contaminated with old impurities can develop its full performance characteristics.

ApplicationsCleaning and flushing out the oil circuits of gasoline and diesel engines. The use of Engine Flush is dependent on the degree of contamination of the oil circuit. Not suitable for use on motorbikes with wet clutches. One 300ml can is sufficient for up to 6 liters of oil. Add engine flush to the motor oil at running temp, before changing the oil, . After adding the product, allow the engine to idle for approx. 10 minutes. Then change the oil and the filter, Engine Flush is compatible with all commercially available motor oils.

1. Soluble Cutting Oil* Cut Ess Lite* Cut Ess* Cut Ess Spl2. Straight Cutting Oil* Honilo 941* Honilo 9433. Semi-Synthetic Cutting Oil* Cut 70004. Synthetic Cutting Oil* Synth. Cut Ess

The highly effective detergent and dispersant additives in association with the carrier fluid have been tested in the laboratory and in practical field trials for their ability to dissolve sludge and lacquer formers. All types of oil-soluble and oil-insoluble residues are brought in to suspension and removed during the following oil change. An engine, which has been cleaned of deposits and contamination and is then filled with fresh oil that is not contaminated with old impurities, can develop its full performance characteristics.

Cleaning and flushing out the oil systems of gasoline and diesel engines.

Note: Not suitable for use on motorbikes with wet clutches.

Cut Ess Spl. is an amber transparent water soluble oil cutting and grinding fluid that becomes whitish in color upon dilution. This product is specifically designed to achieve lubrication without the use of typical EP (Extreme Pressure) additives and is formulated for the general machining and grinding of both ferrous & non-ferrous metals. This product performs across a broad range of metals in a variety of applications.

General Application

• Turning
• Boring
• Milling
• Grinding

Attributes

• Good Corrosion Protection
• Good Surface Finish
• Excellent Tool Life
• Use with steel, Stainless, Cast Iron & Copper Alloys
• Non-staining to Non-ferrous Alloys.

'HYDROL' is a yellow clear fluid has high viscosity index, so it maintains appropriate viscosity range at various temperatures. Maintaining a consistent viscosity at different temperatures is vital for proper lubrication and equipment protection. The ability of lubracting oil to flow readily at cold temperature and still provide protection at warmen temperatures is know as its viscosity index. The higher the viscosity index, the more likely an oil will remain within appropriate viscosity range at various temperatures.

General Application'HYDROL' can be used in wide variety of equipment including hydraulic systems on farm implements, fleet and construction applications, mining equipment hydraulic presses, machine tools, oil lubricated electric motors and generators, palletizers, gear sets requiring and premium quality hydraulic oil. SYM hydrol can also be used for those compressors which call for a non-detergent motor oil.

Attributes

• High Viscosity Index
• Eliminate Metal-to-Metal Contact
• Reduction in Wear
• By Eliminating Metal Contact Increase Life of Equipment

Cut Ess is a brown water soluble oil cutting and grinding fluid that becomes whitish in color upon dilution. This product is specifically designed as a general purpose soluble oil for ferrous metals applications. This product is generally used where ferrous metal are the majority of material being machined.

General Application

• Turning
• Boring
• Milling
• Grinding

Attributes

• Good Corrosion Protection
• Good Surface Finish
• High Cooling Characteristics
• Enhanced Tool Life
• Better Thermal stability of emulsion

Cut 7000 Strong is a clear dark green semi-synthetic cutting fluid. It maintains a constant PH value for a long period of time. It assures uniform concentrated oil drops on the cutting tools, that ensures high quality finishing on the component being worked on. It has enhanced performance characteristics. It can be used on all cutting tool materials namely HSS coated / unquoted, Tungsten coated / unquoted PCD ceramic etc. It can be used for all ferrous and non-ferrous alloys.

General Application

• Sawing
• Boring
• Drilling
• Milling
• Turning
• Tapping
• Facing

Attributes

• Good Corrosion Protection
• Good Detergency
• High workpiece visibility
• Long Fluid Life
• High Thermal Stability

Cut Ess Lite is a dark brown transparent water soluble oil cutting and grinding fluid that becomes whitish in color upon dilution. It is designed for use in medium duty machining applications of ferrous metals. It is used where there are variety of materials and applications.

General Application

• Turning
• Boring
• Milling
• Grinding

Attributes

• Good Corrosion Protection
• Good Tool Life
• High Cooling Characteristics
• Good Surface Finish
• Broad Material & Application use

Provides excellent thermal and oxidation stability. It helps in the smooth functioning of gear changing / shifting and long drain period intervals. Anti-foaming characteristics and protection against wear due to EP additives. Long service life even after high temperature operation.

General Applications & AttributesHypoid spiral bevel or worm gear transmission system of passenger car, buses, trucks requiring EP type additives. Power transmission units of vehicles operating at low temperature steering gear. It is also used in gear boxes of machienery. 

EP-2 GREASE is a lithium based grease made from high quality base oil and thickening agents and EP additives.

 

General Application:

• SYM upgraded range of multi purpose greases are designed to perform in diverse conditions, including moderate to high loads, wide operating temperatures and low to moderate speeds.
• Equipped with anti oxidizing additives, these high performance greases provide extended lubrication life in spite of exposure to dust, dirt and water as well.
• Corrosion inhibitors within grease protect contact surfaces against rust formation.

 

Attributes:

• Excellent performance even when subjected to extremely heavy shear.
• Fine Structural Stability over Long Period of Service.
• Possesses appropriate pumpability for easy application.

000 grease is a lithium based grease made from high quality base oil and thickening agents and EP additives

General Application

• SYM 000 GREASE is a high performance grease with extreme pressure additives for high (shock) loads.
• It is especially developed for trucks and buses, but also for applications with a central lubrication system.
• It is semi-fluid and has a homegeneous structure, providing a good pumpability.
• It is also used in plastic moulding machines for lubrication purpose.

Attributes

• High Lubricity
• Water Resistant
• Lower Cost

00 grease is a lithium based grease made from high quality base oil and thickening agents and EP additives.

General Application

• SYM 00 GREASE is a high performance grease with extreme pressure additives for high (shock) loads.
• It is especially developed for applications with a central lubrication system.
• It is semi-fluid and has a homegeneous structure, providing a good pumpability.
• It is also used in plastic moulding machines for lubrication purpose.

Attributes

• Excellent performance even when subjected to extremely heavy shear.
• Fine Structural Stability over Long Period of Service.
• Possesses appropriate pumpability for easy application.

It is a premium quality lithium soap based multi functional grease processed from premium quality base oil and imported chemicals. Possesses high water resistance properties.

General ApplicationAll types of Automotive, Industrial and general purpose machine such as Wheel Bearing, Universal joints, Dynamos chasis starter Motor bearings. Industrial bearing and ball bearing etc.

Attributes

• Suitable for high temperature application
• Excellent shear stability and water repellency
• Resistance towards oxidation
• Excellent rust prevention

Available in various NLGI penetration BIS 7623/1993, NLGI-3.

1. Cut Ess Spl Soluble Cutting Oil Features :- * Good Corrosion Protection * Good Surface Finish * Excellent Tool Life * Use With Steal, Stainless, Cast Irons & Copper Alloys * Non-Staining to Non-Ferrous Alloy 2. Cut Ess Lite Soluble Cutting Oil Features :- * Good Corrosion Protection * Good Tool Life * High Cooling Characteristics * Good Surface Finish * Broad Material and Application Use 3. Cut Ess Soluble Cutting Oil Features :- * Good Corrosion Protection * Enhanced Tool Life * High Cooling Characteristics * Good Surface Finish * Better Thermal Stability of Emulsion

This is a special quality quenching oil with high cooling power, provides excellent quenching performance for all types of hardening operations, ranging from group quenching of small work-piece to separate quenching of large alloy steel products. It gives very stable performance in atmospheric bath furnaces.

SYNTH. CUT ESS is a amber clear synthetic cutting fluid and becomes fluorescent green in color upon dilution and is formulated with premium EP (Extreme Pressure) package and is designed primarily for moderate to heavy machining of ferrous and non ferrous metals.

General Application

• Sawing
• Deep Hole Drilling
• Tapping

Attributes

• Good Corrosion Protection
• High workpiece visibility
• Long Fluid Life
• High Thermal Stability

A concentrate specially developed for cooling systems in general but particularly those in motor vehicles. Dissolves contaminants containing lime and oil in radiators, heating systems, pipes and in engines. Modern formula containing complex ants with active cleaning agents.

 

Applications: Suitable for all cooling water systems in motor vehicles, buses and commercial vehicles. Add contents to the cooling water. Run the heating system. Depending on the degree of contamination, let the engine run approximately 10 to 30 minutes. Drain the cleaner and flush out the cooling system with water. Fill the cooling system according to the manufacturer's instructions. The contents (300 ml) is sufficient for 10 liters of water.

For us ensuring distribution of order on time is not a big thing is easy, as we have a dynamic logistic system that empowers us to reach patrons within the promised time. Only high quality raw materials have been used for the production of our products as we comply with all quality standards.

With us, one can stay completely assured for safe and dependable payment procedures. Being a client-centric firm, we are dedicatedly involved in making available quality marine oil.