Product / Services
Post Buy Requirement

My ExportersIndia

For Buyer

For Seller

For Help

PT

Prosoft Technology
location Patparganj, Delhi

Write a Review
Call Now Call Now

Our Products

  1. Telecommunication Equipment & System 8 Products available
  2. Ethernet Device 5 Products available
  3. Computer Cables, Adapters & Modules 1 Products available
  4. Laptops, Computers & Mainframes 1 Products available
  5. Audio Video System 1 Products available
  6. Network Interface Card 1 Products available
  7. Gates 1 Products available
  8. Others Products 42 Products available

Our Products

Our product range contains a wide range of Modbus Slave Network Interface Module, CAN bus Extenders WRC-CANX, BM-xx00-RM1K Wireless IO Radio Kit, Multi-Point Wireless I O Radio Kit and Analog I O V Module

ILX69 PROFIBUS Slave Module

ILX69 PROFIBUS Slave Module
  • Feature Rockwell Automation Encompass Approved PI Certified Remote diagnostics via Ethernet
  • PROFIBUS DP Cyclic Data 244 Bytes IN / 244 Bytes OUT
  • Acyclic Read/Writes 240 Bytes
The ILX69 PROFIBUS Slave module is an in-chassis PROFIBUS DPV1 Slave for CompactLogix, supporting cyclic PROFIBUS IO data and acyclic messaging. Explicit ladder logic CIP message blocks provide slave status diagnostic data and the ability for acyclic messaging.The ILX69 interface appears to the CompactLogix controller as a standard IO module allowing it to be configured via StudioRSLogix5000. The cyclic PROFIBUS IO data can be configured in StudioRSLogix 5000, or configuration can be transferred from the Master to the slave module. The Ethernet interface allows for remote diagnostic and troubleshooting. Complete program examples for simple and quick start-up are available.
View Complete Details
Ask Latest Price & Details
Modbus Plus Dual Port Network Interface Module

Modbus Plus Dual Port Network Interface Module
  • Feature Foreign device data concentrator, Pipelines and offshore platforms
  • Single Slot - 1756 backplane compatible
The MVI56 Modbus Plus Dual Port Network Interface Module allow Rockwell Automation ControlLogix processors to connect directly on Modbus Plus networks as a peer. The module acts as an inputoutput module between the Modbus Plus network and the processor. Compatible devices can be found in most industries and include devices such as drives, relays and power monitor hardware.Compatible devices include not only Modicon PLCs (which all support the Modbus Plus protocol) but also a wide assortment of end devices licensed through the ModConnect Program. The MVI56-MBP module acts as an inputoutput module between the Modbus Plus network and the Rockwell Automation backplane. The data transfer from the ControlLogix processor is asynchronous from the actions on the Modbus Plus network. A 4000-word register space in the module exchanges data between the processor and the Modbus Plus network. These modules allow Rockwell Automation platforms to connect directly on Modbus Plus networks as a peer. In addition, the modules act as slaves to processors that must readwrite data from the module's memory. Crossing all industrial boundaries, potential applications include the connection of Rockwell Automation processors to Modicon processors, and the connection of Modbus Plus speaking devices such as drives, relays, and power monitor hardware to the Rockwell Automation backplanes.
View Complete Details
Ask Latest Price & Details
Modbus TCP Server Enhanced Network Interface Module

Modbus TCP Server Enhanced Network Interface Module
  • Specifications Backward compatible with previous MVI56-MNETC versions, Single-slot 1756 ControlLogix backplane compatible
When you need Modbus TCPIP communications, the MVI56E- MNETCMNETCXT is the module of choice. The Modbus TCPIP Enhanced Communications Module allows Rockwell Automation ControlLogix Programmable Automation Controllers (PACs) to interface easily with Modicon Programmable Automation Controller (PACs), as well as multiple Modbus TCPIP server-compatible instruments and devices. The multi-client module improves performance when controlling multiple servers on a Modbus TCPIP network, by supporting up to 30 Clients. It also supports up to 20 server connections providing the ability to communicate with other DCS and SCADA systems. Both client and server functionality can run simultaneously, allowing the module to operate as a powerful data concentrator. The MVI56E-MNETC and MVI56E-MNETCXT are functionally the same. The MVI56E-MNETC is designed for standard process applications. The MVI56E- MNETCXT is designed for the Logix-XT control platform, allowing it to operate in extreme environments. It tolerates higher operating temperatures, and has a conformal coating to protect it from harsh or caustic conditions. MVI56E enhancements include configuration and management through the modules Ethernet port, and CIPconnect technology for bridging though ControlNet and EtherNetIP networks.
View Complete Details
Ask Latest Price & Details
CLX-APACS Module

CLX-APACS Module
  • Purity Supports all standard APACS+ digital and analog I/O modules, Supports up to 39 IO Bus cards per network segment
  • Ports Dual Channel, Redundant Serial RS-485
  • Typical Power Consumption 5 mA @ 24 VDC and 450 mA @ 5.1 VDC
The CLX-APACS module enables a ControlLogix Plant-PAx system to control MooreSiemens APACS+ IO Bus remote IO racks. This provides the ability to execute a phased migration of old Moore APACS DCS systems.
View Complete Details
Ask Latest Price & Details
Fiber-Optic CAN Bus Extenders

Fiber-Optic CAN Bus Extenders
  • Purity Works with both trunk lines and drop lines, Allows operation at higher speeds for specific distances
  • Specifications Up to 12km fiber lengths , CAN 2A, CAN 2B, and remote frame support
WRC CAN bus Extenders boost signal levels, allowing longer cable lengths, longer trunk lines, and longer drop lines without sacrificing network speed. CAN bus Extenders permit maximum network speed and throughput on CAN, J1939, or DeviceNet network devices, resulting in better control of the process. In addition extenders require no configuration when used in DeviceNet applications as they are configured for autobaud operation Comes with the standard two-year Western Reserve Controls warranty
View Complete Details
Ask Latest Price & Details
CAN Bus Extenders WRC-CANX

CAN Bus Extenders WRC-CANX
  • Purity Works with both trunk lines and drop lines, Allows operation at higher speeds for specific distances,
WRC CAN bus Extenders boost signal levels, allowing longer cable lengths, longer trunk lines, and longer drop lines without sacrificing network speed. CAN bus Extenders permit maximum network speed and throughput on CAN, J1939, or DeviceNet network devices, resulting in better control of the process. In addition extenders require no configuration when used in DeviceNet applications as they are configured for autobaud operation. Comes with the standard two-year Western Reserve Controls warranty
View Complete Details
Ask Latest Price & Details
BM-xx00-RM1K Wireless IO Radio Kit

BM-xx00-RM1K Wireless IO Radio Kit
  • Feature Save time and money: Eliminates trenching and running conduit / deploys in minutes, Easy to use: No software configuration needed
  • DIN Rail Mounting Compatibility 35 mm x 7.5 mm DIN Rail
  • DataRail™ (Included with Radio Kit) 6.1 in / 156 mm - Supports up five (5) I/O modules, other lengths also available
  • Built-In Mounting Hardware Spring-loaded clip-on system
How many times do you need to get a few points of digital or analog inputs and outputs from point A to point B, but cant justify the cost of running the wires? The Radio Kit is a replacement for hardwired IO that is simple to deploy. The Kit requires no programming just wire strippers and a screwdriver. There is no communication protocol to interpret. The radios are paired and secured at the factory, so there are no settings or configurations to figure out. It is bi-directional, so digital and analog signals can be sent in both directions between two connected IO stations. Inputs on one module are simply replicated as outputs on the corresponding module. Our wireless IO makes use of the unlicensed ISM band at either 868 MHz, 900 MHz, or 2.4 GHz (USA only). The radios can send IO up to 4 miles for the 900 MHz or 1 mile for the 868 MHz and 2.4 GHz models. Each radio pair can connect up to 16 IO modules, more than enough for most applications.
View Complete Details
Ask Latest Price & Details
Multi-Point Wireless I O Radio Kit

Multi-Point Wireless I O Radio Kit
  • Feature Single power termination per station saves wiring time., AES encryption ensures data is protected from intrusions
  • Device Functionality Multipoint Wireless I/O Gateway
  • Embedded Controller 32-bit Low Power ARM7 Microcontroller with Internal FLASH (Field Upgradeable)
ProSoft Technologys Multi-Point Wireless IO system allows you to monitor IO from multiple locations without running long wires. This secure, reliable system is scalable and deploys quickly, allowing you to skip trenching, conduit, and permits. Three module types: Analog 0-10 V, Analog 4-20 mA, and DigitalDiscrete give you the freedom to customize your setup based on your environment and needs. The system can be used in different methods: IO to IO, IO to Modbus serial communications, and Modbus serial to Modbus Serial communications. This peer-to-peer system can move data from the IO or Modbus devices to any other node. The digital input module can act as a counter and send the accumulated value to another location.
View Complete Details
Ask Latest Price & Details
PSW-PCB ProSoft Configuration Builder Software

PSW-PCB ProSoft Configuration Builder Software
  • Purity . Create plant-wide configurations of all ProSoft Technology products. Manage configuration of complex protocols and networks, including PROFIBUS DP.
Use a single software tool to configure and test all ProLinx modules, as well as a growing selection of ProSoft inRAx and ProTalk modules. ProSoft Configuration Builder simplifies the task of managing the configuration files that control how your ProSoft module operates. ProSoft Configuration Builder also provides the following features: Graphical User Interface replaces the Hyperterminal download and monitor method.Provides error reduction in setting up configuration files.Extensive online help for module-specific configuration options.
View Complete Details
Ask Latest Price & Details
PSW-PWD ProSoft Wireless Designer Software

PSW-PWD ProSoft Wireless Designer Software
  • Purity Visual diagram of site layout Location (latitude/longitude, based on GPS coordinates)
  • Specifications Checks wireless link feasibility based on path length and recommended accessories, Predicts signal st
ProSoft Wireless Designer simplifies the task of planning and specifying your ProSoft Wireless network. The easy to use, wizard-based interface creates a visual layout of your radios and sites, and generates a complete Bill of Materials including radios and accessories.
View Complete Details
Ask Latest Price & Details
Modbus Slave Network Interface Module

Modbus Slave Network Interface Module
  • Dimensions Standard 1769 Single-slot module
  • Current Load 800 mA max @ 5 VDC Power supply distance rating of 2 (L43 and L45 installations on first 2 slots of
  • Operating Temp. 32° F to 140° F (0° C to 60° C)
  • Storage Temp. -40° F to 185° F (-40° C to 85° C)
  • Relative Humidity 5% to 95% (without condensation)
  • LED Indicators Battery and Module Status Application Status Serial Port Activity CFG Port Activity
The MVI69-MCM Modbus MasterSlave Network Interface Module allows Rockwell Automation CompactLogix Programmable Automation Controllers (PACs) and MicroLogix 1769-LRP Programmable Logic Controllers (PLCs) to interface with Modbus-compatible devices. Compatible devices include not only Modicon PLCs but also a wide assortment of third-party devices found in nearly every industry.
View Complete Details
Ask Latest Price & Details
IEC 60870-5-101 Master Network Interface Module For CompactLogix

IEC 60870-5-101 Master Network Interface Module For CompactLogix
The MVI69 IEC 60870-5-101 Master Network Interface Module allows CompactLogix processors to interface easily with IEC 60870-5-101 Slave devices. The MVI69-101M module interfaces up to 32 serial communication devices with the CompactLogix processor. Two communication ports on the module act as controlling devices (Masters) to interface with controlled devices on their own networks. Each port is individually configurable. The MVI69-101M is the ideal solution for many applications where IEC-compatible devices must communicate with the ControlLogix platform. Compatible devices include relays, breakers, sub-station communication modules and other serial communication devices. Functionality of the IEC protocol is very similar to the DNP 3.0 protocol which features time stamping and True Report by Exception (TRBE). These features allow the MVI69-101M module to send a report to the processor without being polled, providing real time data transmission in critical situations.
View Complete Details
Ask Latest Price & Details
Linux Development Module For CompactLogix MVI69E-LDM

Linux Development Module For CompactLogix MVI69E-LDM
  • Slaves Maximum 125
  • Input/Output Maximum 244 Bytes per Slave
  • Input Data Maximum 5712 Bytes
  • Acyclic Data DPV1
The MVI69E-LDM module allows users to develop and deploy CC++ custom algorithm applications for CompactLogix systems. Users are also able to create drivers for specialty Ethernet and Serial end-devices. The Linux Development module comes with a built-in API for backplane communications to the processor. With the separate development kit DVD, you are the developer who controls exactly what this module can and cannot do.
View Complete Details
Ask Latest Price & Details
HART Master Multi-drop Network Interface Module For ControlLogix

HART Master Multi-drop Network Interface Module For ControlLogix
The MVI56-HART Master Multi-drop Network Interface Module allows ControlLogix IO compatible processors to easily communicate with HART slave devices. The MVI56-HART module interfaces up to 15 devices on each HART channel with the ControlLogix processor. Four channels on the module support master protocol commands to interface with slave devices on their own networks. Each port is individually configurable. Data is exchanged between the HART network and the ControlLogix processor using the internal database contained in the module and direct control by the processor's ladder logic and pre-defined data objects (5000 registers maximum).The MVI56-HART module is the perfect solution for industrial applications in chemical and refining operations, gas and liquid distribution systems, and remote offshore monitoring stations, addressing virtually all aspects of control, data acquisition, and maintenance.
View Complete Details
Ask Latest Price & Details
Analog I O V Module

Analog I O V Module
The analog 0-10 V IO module provides two 24-bit inputs and two 16-bit outputs. The IO modules offer 2500 V r.m.s. isolation, with a wide operating temperature range and Class I Division 2 hazardous location rating, making them ideal for demanding industrial installations. Connect them to the wireless IO radios for point-to-point wire replacement applications, or to the RS485 IO Extension module to add IO to a Modbus network.
View Complete Details
Ask Latest Price & Details
Modbus Plus Dual Port Network Interface Module

Modbus Plus Dual Port Network Interface Module
The MVI46 Modbus Plus Dual Port Network Interface Module allow Rockwell Automation SLC processors to connect directly on Modbus Plus networks as a peer. The module acts as an inputoutput module between the Modbus Plus network and the processor. Compatible devices can be found in most industries and include devices such as drives, relays and power monitor hardware.
View Complete Details
Ask Latest Price & Details
Tell Us What are you looking for? Will call you back

Contact Us

View Contact No.