Our Products
DESIGNED FOR ALL TRACTION BATTERY VOLTAGES VIZ.24, 30, 36, 48, 72, 80 V DC. OF FLOODED / SMF / VRLA TYPE. THE SAID PCB HAS A MASTER SLAVE MICROPROCESSOR CHIP COMBINATION. A PROGRAM DEVICED TO MONITOR CHARGING PROCESS OF BATTERY IS STORED IN IT. THIS PROCESSOR IS CONTROLLER ENABLE TO TERMINATE THE CHARGING PROCESS. ACCOUNT IS TAKEN OF BATTERY AGE, DEPTH OF DISCHARGE, CORRECT BATTERY & WRONG CONNECTION TO MOTOR. STATUS OF BATTERY CHARGE STATE IS SHOWN BY TRAIN OF LEDS CONNECTED BY A BUS TO THE SAID PCB
We are offering transformer. Double wound, step-down transformer made from high quality annameled dpc copper wire of circular & square cross selection & having crgo lamination as core. Transformer core is cylindrically designed to overcome losses and achieve maximum efficiency high packing fraction enables compact transformer design & reduces heating in high load condition ballast choke is single wound inductor made of crno lamination &anameled copper wire set to perfection to controll current & voltage drop at perticular current load. Setting only possible at factory.
DOUBLE WOUND, STEP-DOWN TRANSFORMER MADE FROM HIGH QUALITY ANNAMELED / DPC COPPER WIRE OF CIRCULAR & SQUARE CROSS SELECTION & HAVING CRGO LAMINATION AS CORE. TRANSFORMER CORE IS CYLINDRICALLY DESIGNED TO OVERCOME LOSSES AND ACHIEVE MAXIMUM EFFICIENCY HIGH PACKING FRACTION ENABLES COMPACT TRANSFORMER DESIGN & REDUCES HEATING IN HIGH LOAD CONDITION BALLAST CHOKE IS SINGLE WOUND INDUCTOR MADE OF CRNO LAMINATION &ANAMELED COPPER WIRE SET TO PERFECTION TO CONTROLL CURRENT & VOLTAGE DROP AT PERTICULAR CURRENT LOAD. SETTING ONLY POSSIBLE AT FACTORY.
We are Manufacturer of battery chargers for lead - acid & alkaline battery's used for traction application & auxillariy power/ tripingcircuit. Our traction charger are basically used for material handaling application like forklifts, stackers & pallets. Auxillary power, application being viz. To drive panels used for operating pumps, equipments for telecom, electromagnetic cranes, power station tripping-unit. Smaller versions of these chargers are used for forefighting, Dg set equipments.
FLOAT-BOOST CHARGERare the equipment whhich fall in the later type of chargers . Our chargers are made of rectifier which are diode bases, DIODE- thyristor hybird (semi controled or fully thyristor based (fully controlled) we also manufacture mosfet based smps compact chargers in same category.
PHYSICAL FEATURES :
Cabinates is made of ms angles and crc sheets of # 18 - # 14 .Fully in house fabricated and duly pinted. (paint siemens grey or dove greay) or of customer colour choice. Powder coating optional.Transformers, choke doubly wound with B- class copper wire. (F- class on customer requist.) bus-bar aluminium or copper. All fitting's of branded company like Kaycee, Switch- on, Phillips, Siemens & L&T . All control circuit board made of glass epoxy base.
Cabinate approx dimensions : 600MM 650MM 1600MM (W*D*H) or as per design requirment smps come in 24V/ 30V/ 48V with 10, 20, & 50Amps design
Having Sizes : 300MM * 350MM * 200MM (W*D*H) as per design requirment
CURRENT CONTROL | Constant current : 1AMPS TO MAX ( as set per design) variation continuous. |
VOLTAGE | Constant voltage. |
CHARGING MODE | FLOAT & BOOST : Switching automatic or manually. |
WITHIN CHARGER | Charger can be FLOAT CUM BOOST, FLOAT CUM BOOST |
INDICATION | Pilot lamps for Input phase indication. Charger on Float or boost mode indication Over current protection Under voltage/ over voltage |
METERING | Input voltage indicator Input current - optional Output current Output voltage Battery current - optional meter analog (Moving coil type) Size (96*96) or Digital panel meter type (96* 48) |
RIPPLE | < 5% normally, < 1% on request. On full load (additional Charges) |