Other Products / Services #2972103

Power Control Centre is used for distribution and control of various power source used in industry. Normally Power Control Centers is installed near power source hence fault level is high. It is designed to suit fault level of 50KA or 65 KA for 1 sec. Busbar system in Power Control Centers are designed to suit the fault level as well as temperature rise to 40c above ambient. Ample space is provided for cable termination. Various protections viz short circuit, overload, earth fault, under voltage etc are provided to protect source and equipment. We are engaged in manufacturing of power control centers from the best raw materials. We meet the requirements of International Standards along with compliance to local standards and regulations. The complete structure shall be rigid, self-supporting & free from twists and bends. The panels will be totally dust and vermin proof. They will have fixed or draw out type. Bus Bars are supported by SMC /DMC bases will be employed throughout the length of the panel. Internal wiring be carried out with 11000/650 volt grade PVC insulated stranded conductor wire. All joints will be solidly crimped using copper thimbles . Earthing Bus Bars will be running all along the board.

Power Distribution Panels are used for distribution of power on down streams. Since it is located at downstream fault level is normally lower about 20 to 35 KA. Normally it is designed to carry current up to 800A. Advantage of using Power Distribution Panel is to clear fault locally hence it does not affect Upstream Switchgear

Industrial and commercial installations in our country have large electrical loads which are severely inductive in nature, such as motors, large machines, air conditioners, drivers etc. which causes a severely lagging power factor. This lagging power factor results in loss and wastage of energy and thus heavy penalties by electricity boards. In case of fixed loads this can be taken care by manual switching of capacitors. However in case of rapidly varying and scattered loads it becomes difficult to maintain a high power factor and hence manually switching on/off the capacitors in proportion to variation of load within an installation is next to impossible. This drawback can be overcome by using an APFC panel (Automatic Power Factor Correction Panel) which not only maintains a high power factor but also eliminates the need for constant manual intervention. The ratio of Active Power to Apparent Power is called Power Factor which is equal to Active Power/ Apparent Power

• Prevents leading power factor in the installation during low load conditions
• Improves efficiency of the system by reducing losses
• Reduces the KVA demand charges
• Ability to maintain a constant high power factor
• Economical with faster payback periods
• Eliminates low power factor penalties levied by EB

We engaged in manufacturing and supplying a diverse range of PLC Based Automation Panels. These control panels are reckoned by the clients for providing higher output with less power consumption. Compactly designed, our range of auto machine PLC control panels are largely used in various applications. Available in different specifications, these are offered at market leading prices.

We are involved in the Manufacturing and Supplying of high performingDG Synchronization Panels. The range of DG Synchronization Panels comes complete with Controlling & Protection Relays capable of synchronizing of more than one DG sets / with Mains & DG and with necessary protections. We offer the DG Synchronization Panels at affordable rates to clients.

We are into Manufacturing and Supplying an effective range of Electrical Feeder Pillar that caters to the specific requirements for various application areas such as Industries, townships housing societies. We are leading supplier of feeder pillar to various govt depts. We manufacture feeder pillars as per CPWD guidelines.

We manufacture high quality distribution boards distribution boxes and MCB boxes for domestic and industrial purposes. We bring forth a wide range of Power Distribution Panels that is an electricity supply system. For industrial purposes the Power Distribution Panel divide electric power feed into several circuits and can be availed with MCCB / SFU /MCB. For domestic requirements such as residential buildings and housing societies these Distribution boards/boxes can be fitted with energy meter from supply company(such as TATA Power, BSES, NDPL etc.) , MCBS for distribution, ELCBs, main switch of the entire building and provision of generator, invertor and UPS connection. The Power Distribution Panels are fully equipped with all necessary safety precautions.

• Durable finish standards
• Heat resistant
• Corrosion resistant
• Sturdy construction
• Energy efficient

Bus duct is used for the effective and efficient supply of electricity in mostly industrial locations. Copper or aluminum is used for the conductor of bus duct that be insulated and enclosed completely for protection against mechanical damage and dust accumulation. A bus duct system is an effective method of distributing power to your switchgear and various loads. However, bus duct problems can lead to catastrophic damage and extensive downtime. We offer a wide range of durable Bus Duct that comes complete with CRCA /Stainless Steel / Aluminum enclosures for ensuring their safety from any wear and tear. Our array of Bus Duct systems are type tested with Erection & Commissioning services. We hold the expertise in design, engineering and manufacturing of various types of bus ducts with a range up to 6300 ampere. Our Bus Ducts are available in both Aluminum and Bus as per requirements and mostly custom built suitable to layout, Site conditions and Application. Our bus ducts are available with accessories required such as flexible joints to easily connect transformer terminals or D. G. Terminals.