SHIVAM INSTRUMENTS

Wazirpur, Delhi

• Compact table model
• 20 cm dia Top and Adopter to hold polishing cloth or paste
• Sample Holders to accommodate upto NX size Cores
• Continuous water feed arrangement during operation

This bench mounted, single spindle lapping machine is ideally suited for the final polishing of mounted rock or concrete specimens.
Two sample holders of sample size ordered for are provided with each machine as standard supply. Sample holders of other sizes can also be provided on request. This is a motor driven unit with 450/500 rpm. A swing-in tap, for continuous water supply during operation, is also provided. This unit is operated by a single phase, 230 V, AC motor.

Double walled construction. Inner chamber made of S.Steel & outer Mild Steel painted with white stoving enamel. S.Steel Trays to hold Blood Bags with separate acrylic door for each compartment. Temperature can be controlled up till 0C by Electronic Digital. Temperature Controller cum indicator with an accuracy of +/-0.5C. Built in safety audio/visual alarms such as door opening alarm, temperature fluctuation alarm, power failure alarm are provided with the controller itself. A sealed condensing unit/compressor with all accessories and fan cooled condenser are fitted at the bottom below working chamber. Inside temperature uniformity is maintained by air circulation fans. Suitable to work on 220/230 V, 50Hz. Single phase AC supply

Capacity

• 85 Liters. (50 blood bags)
• 165 Liters. (100 blood bags)
• 200 Liters. (200 blood bags)
• 280 Liters. (250 blood bags)

Optional Accessories

• Temperature chart recorder facility
• Voltage Stabilizer 4 KVA

Double walled construction. Inner chamber made of stainless and outer Mild steel painted with white stoving enamel. A water drain cock & stainless steel tray is provided at the base of the chamber. Temperature can be controlled up to -20C by electronics Digital temperature controller cum indicator. High grade puf insulation is provided between the walls to achieve set temperature in short time. A sealed condensing unit of Kirloskar / Techmshah fitted at the bottom below working chamber. Suitable to work on 220/230 V, 50 Hz. Single phase AC supply.

Pavement Core Drilling Machine
Salt Mist Chamber
Salt mist chamber is used for Salt Fog Testing and Corrosion Testing in Salt laden atmosphere.

• Working temperature range is ambient to 55 C
• Humidity Range: Upto Saturation Limit
• Control of Temperature: By P.I.D controller Digital Readout of set and actual values
• Testing Chamber: Acrylic Glass of 8 mm thick, Nozzle made of Acrylic plastic
• Heating: SS Heating Element, 0.75 kW, 230 V, single phase AC, fitted in the salt solution tank
• Solution Tank: Made of Fiber Glass, Double walled, capacity 35 litres approx, with provision for water level
• Chamber Stand: Made of MS Angle.
• Unit is supplied with SS rods and hooks for hanging samples Designed to deliver compressed air at a controlled rate.

The following sizes are available
Salt Mist Chamber size 45 x 45 x 45 cm
Salt Mist Chamber size 45 x 45 x 60 cm
Salt Mist Chamber size 40 x 50 x 75 cm
Salt Mist Chamber size 40 x 50 x 90 cm
Salt Mist Chamber size 45 x 60 x 60 cm
Salt Mist Chamber size 45 x 60 x 90 cm
Salt Mist Chamber size 60 x 60 x 60 cm
Salt Mist Chamber size 60 x 60 x 90 cm
Salt Mist Chamber size 60 x 60 x100 cm
Salt Mist Chamber size 90 x 60 x90 cm

IS: 2720 (Part 2) - 1973 IS: 12175-1987
Using a speedy moisture meter, the moisture content of soils, sand and other fine-grained material can be obtained quickly with reasonable accuracy. The test technique is based on the fact that water will react with calcium carbide to form acetylene gas and the quantity of gas formed is directly proportional to the water present, leaving a surplus of the chemical used in the test. The quantity of acetylene gas produced is indicated on a built-in pressure gauge, which is calibrated in percentage of moisture on wet weight basis.

IS: 4031
A specially designed Vibration Machine is used for vibrating the mix in moulds according to strictly controlled programmer at a frequency of 12, 000 400 cycles per minute. The Vibrator is mounted over coiled springs and the vibrations are developed by means of a revolving eccentric shaft. The center of gravity of the vibrator, including the cube and mould, is either at the center of the eccentric shaft or within 25 mm below it. The simple design of the machine facilitates easy assembly and dismantling of the cube moulds. The machine is suitable for operation on 230 V, 50 Hz, and single-phase, AC supply. Each machine is supplied with one cube mould.
The following mould can be ordered, as optional extra
MouldM. Steel, for 70.6 cm cube
NoteThe machine can certified for its frequency by the National Council of Cement and Building Materials (NCCBM) at Extra Cost.