Our Products
we introduce electro-perm magnetic chucks for heavy duty milling machine. These chucks ensure high magnetic and mechanical performance. Also known as epm chucks, this chuck is "cold device, as there is no internal wear or deformation as a result of moving internal parts. Electro-perm magnetic chucks do not consume electrical power except for the very short period of activation or deactivation of the working surface. Once fixed to the machine table, epm chucks are as stable as machine. Epm chucks are economical for operation and maintenance. Magnetic clamping system is most powerful. Chucks are switched on & off by simple electrical pulse. A variable output from 20% to 100 % is controlled from push button unit. In operating condition, no power supply is necessary for holding work pieces. So there is no risk when power fails. The de-magnetization cycle of chuck eliminates possible residual magnetism in work piece; therefore there is easy release for high alloy steel parts. Epm chuck is designed for heavy-duty operation such as milling cut of 3 to 6 mm depth at recommended speed & feed. accessories
Specifications
Cat No. | Sizes in mm (L x W x H) |
---|---|
EPMC - 2412 | 600 x 300 x 90 |
EPMC - 3012 | 750 x 300 x 90 |
EPMC - 4012 | 1000 x 300 x 90 |
EPMC - 6012 | 1500 x 300 x 90 |
EPMC - 2416 | 600 x 400 x 90 |
EPMC - 3016 | 750 x 400 x 90 |
EPMC - 4016 | 1000 x 400 x 90 |
EPMC - 6016 | 1500 x 400 x 90 |
NOTE:Other specific sizes as per the customers requirement will be catered in
RADE ‘A ’ GRADE ‘ B ’
CAT. NO. LWH CAT. NO.
SH – A 1001 100 * 10 * 5 SH – B 1001
SH – A 1002 100 * 20 * 10 SH – B 1002
SH – A 1003 150 * 15 * 10 SH – B 1003
SH – A 1004 150 * 20 * 15 SH – B 1004
SH – A 1005 150 * 30 * 20 SH – B 1005
SH – A 1006 200 * 30 * 20 SH – B 1006
SH – A 1007 200 * 40 * 25 SH – B 1007
SH – A 1008 200 * 50 * 30 SH – B 1008
SH – A 1009 250 * 40 * 25 SH – B 1009
SH – A 1010 250 * 50 * 30 SH – B 1010
SH – A 1011 250 * 60 * 40 SH – B 1011
SH – A 1012 300 * 50 * 25 SH – B 1012
SH – A 1013 300 * 60 * 30 SH – B 1013
SH – A 1014 300 * 70 * 40 SH – B 1014
SH – A 1015 400 * 50 * 50 SH – B 1015
SH – A 1016 400 * 75 * 50 SH – B 1016
SH – A 1017 400 * 100 * 50 SH – B 1017
SH – A 1018 450 * 50 * 50 SH – B 1018
SH – A 1019 450 * 75 * 50 SH – B 1019
SH – A 1020 450 * 100 *50 SH – B 1020
Steel case hardened. Ends of jaws chamfered to facilitate clamping under shoulder or in recess. Clip holds loose jaw in position when clamp screw is released.
CAT.NO. LENGTH OF JAW OPENING
401 1.5” (38 mm) 5/8” (17 mm)
402 2” (51 mm) 1” (25 mm)
403 3” (75 mm) 1.5/8” (41 mm)
404 4” (102 mm) 2.5” (64 mm)
405 5” (127mm) 3.5” (89 mm)
‘KUMAUN’ magnetic pencil is very useful for removing steel particles from blind holes and useful for assembly & maintenance work for removing steel parts lying in oil tanks.
‘KUMAUN’ magnetic pencil is compact unit embodying powerful NdFeB magnets assembled in stainless steel pots, which are designed for lifting operations.
Connecting extension can increase length.
Made from high resistant steel.Contact surface precision ground and lapped.Fully hardened up to 58 Rc up to 300 mm length& above 300 mm length WorkingEdges are hardened to 58 Rc.
SPECIFICATIONS:
Cat No.Sizes mm.LWTSH-1102 KE50 x 30 x 8SH-1103 KE75 x 35 x 8SH-1104 KE100 x 40 x 10SH-1106 KE150 x 40 x 10SH-1108 KE200 x 50 x 12SH-1110 KE 250 x 50 x 12SH-1112 KE 300 x 60 x 12SH-1120 KE 500 x 50 x 15SH-1124 KE 600 x 60 x 20
Ground with parallelism, flatness, and square ness within 5 microns.
These blocks have no magnetism but when placed parallel to poles of chuck, they transfer magnetic power to top and sides for holding.
Available with V shaped face for holding round jobs.
One pair of blocks is finished together.
This 787 Universal Dial Indicator Set has a spiral type mechanism of unusually rugged construction for the more severe applications around machinery and for general tool work. The indicator can be supplied in inches as well as in metrics. The hole attachment used in conjunction with any standard dial indictor make it possible to test inside of holes and many other surfaces that can not be reached with the regular indicator spindle. The each attachment has a 0.375” diameter hole to fit all indicators and are securely clamped to the indicator stem by means of a knurled screw. The ball end of the swivel arm, which contacts the work, is 1/ 8 “diameter and the body of the arm is 3 / 16” diameter.
Code : KM - 787
These Boring tool devices are used to set boring tool to the exact diameter on boring machines and machine tools with rotation boring tools. Because of their magnetic bases, they can be held directly on boring spindle. The clamps can fit at any desired position whereby any particular bore size can be set on the device. These devices have ON / OFF switches, as per requirements and aid in holding the job on boring spindle. The ‘ V ‘ slot is ground to 5micron accuracy.
We have a skilled team of quality experts that stringently checks each and every product at different stages. With the best in class raw material comes a remarkable finished product, thus we keep a stern check on the material used. Our quality auditors ensure that the products are up to the mark.
This tool is useful for testing spindle run out of machine tools, lathe work etc. It is well adapted for inspection of the parallelism of surfaces. The indicator can be swiveled in all directions. The base is of steel and provided With T slots for convenience in clamping. The surfaces of the base are accurately ground. New clamping system ensures quicker rigid clamping even with moderate tightening. The holder for the dial indicator is equipped with fine adjustment device permitting vibration free adjustment to zero.
Specifications
Code | KM - 300 |
---|---|
Length of base | 250 mm |
Width of base | 50 mm |
Height of base | 35 mm |
Height of column | 225 mm |
Diameter of column | 18 mm |
Used on similar application as Button Magnets, but are more powerful. Pot made up on mild steel with brass spacer and Magnet Alnico V.
Steel case hardened. Ends of jaws chamfered to facilitate clamping under shoulder or in recess. Clip holds loose jaw in position when clamp screw is released.
We make sure that our inputs are in conformation with the international quality standards and free from all sorts of impurities in order to offer quality-approved products to the buyers. Due to our superior transit system and vast distribution network, buyers can be rest assured for timely delivery.
Features :
Used for Precision measurement, setting of angles & Light machining
Accuracy for Square ness, Flatness & Parallelism
within 0.005mm up to 200L & 0.010mm up to 450L
Angle can be set within ±5 seconds
Centre Distance between rollers is within 0.005mm
Made from high quality alloy steel
Hardness - 60 ± 2 Rc & Tempered
Magnetic Table for job holding
Firm hinged clamp to reduce possibility of distortion
Cat. No Size (mm) Center Distance Inclination
SH-301MST 150 L x 120 W x 105 H 70 mm 0 - 45º
SH-302MST 250 L x 150 W x 105 H 100 mm 0 - 45º
SH-303MST 300 L x 150 W x 105 H 100 mm 0 - 45º
SH-304MST 450 L x 150 W x 105 H 100 mm 0 - 45º
SH-305MST 500 L x 200 W x 105 H 150 mm 0 - 45º
Cat. No Size (mm) Center Distance Inclination
SH-301MST 150 L x 120 W x 105 H 70 mm 0 - 45º
SH-302MST 250 L x 150 W x 105 H 100 mm 0 - 45º
SH-303MST 300 L x 150 W x 105 H 100 mm 0 - 45º
SH-304MST 450 L x 150 W x 105 H 100 mm 0 - 45º
SH-305MST 500 L x 200 W x 105 H 150 mm 0 - 45º
Essential cleaning unit for iron particles from re-circulating coolant in grinding machines
Capable of continuous removal of ferro-magnetic contamination
Powerful permanent magnet rotates attracting fine iron particles from coolant flow
Spring loaded rubber roller squeezes and drop back the coolant in tank
Iron sledges are removed by scraper blade, which can be adjusted
These can be easily dismantled for maintenance
Supplied complete with driving gear/motor assembly
Generally made with strontium ferrite magnets, can also be made with rare earth NdFEB magnets
Cat. No. Capacity in L pm Driving Power (Hp) Rotation
KM110 30 0.25 10 RPM
KM111 60 0.50 10 RPM
KM112 100 0.75 10 RPM
KM113 150 1.75 10 RPM
KM114 200 1.50 10 RPM
Coil type demagnetizer is designed to operate on alternative current to demagnetize a work-piece. Just pass through the coil and remove it from the field of the demagnetizer. Care should be taken to assure that work-piece is well away from the demagnetizer before the magnetizer is switched OFF. KUMAUN type demagnetizer is very useful for rods, bars, small jobs, etc.
To ensure complete safety of the products from diverse damaging factors such as rain, dust, sunlight, moisture, etc., we keep the lot in our capacious warehouse before dispatch. Purchasers across Maharashtra(India) and other market places can get in touch with us for buying our product as per requirement.
These tri squares come with these special inbuilt features :
Due to our superior transit system and vast distribution network, buyers can be rest assured for timely delivery. Our raw materials are essential bottleneck assets and thus these are carefully selected by our expert quality auditors after checking against varied quality parameters.
These tri squares come with these special inbuilt features :
Far-famed for the outstanding range of Roller Bearing V Blocks; we are a leading name in this trade. For safe assembling of all the products, we have invested our time and money in the capacious storage unit that helps us in keeping the products safe till final delivery to the clients.
The V Blocks have two V angles of different size to take parts of varying dimensions. By means of the clamp the Work can be held tight in the block. The accuracy of the vee block/100mm is within 0.005 mm.
We have the latest equipment and technology for the strict checking of raw material at the initial stage only. We ensure that prior to manufacturing the material is checked on the grounds of quality. As we have a wide distribution network, we are able to ensure our payment procedures are fast and simple. Additionally, we are capable of providing prompt payment discounts.
Specifications :
This Magnetic Knee or holder is designed to hold work magnetically for Inspection as well as layout work. It is very useful for holding odd shaped parts for grinding, as it has a large magnetic surface of 100 * 275 mm precision ground. The accuracy for flatness parallelism and square ness is within 0.005 mm.
Specifications :
These tri squares come with these special inbuilt features:Made from single piece of fully seasoned, fine quality steel.Squares having accurate right angles on both sides.Beam & blade are accurately lapped for straightness & parallelism.All squares are fully hardened to 58 (+-2) Rc.Beam is grooved at inner corner for clearance of burns & dirt.Blades are beveled on each side.
These tri squares come with these special inbuilt features:
Made from single piece of fully seasoned, fine quality steel.
Squares having accurate right angles both inside & outside.
Beam & blade are accurately lapped for straightness & parallelism.
All squares are fully hardened to 58 (+-2) Rc.
Beam is grooved at inner corner for clearance of burns & dirt.
Packed in individual wooden box.
Two magnetic holders link together, providing a means of mounting work pieces at right angle, having accuracy of 5 micron. Provides facilitation of assembly procedures or operations such as welding.
Specifications :
Due to our superior transit system and vast distribution network, buyers can be rest assured for timely delivery. We have a dedicated staff that ensures the quality of material used for designing and production. The inspection is done on the initial stages to make the final product free from defect.