STP Limited, India, waterproofers to the nation since 1935 and Carlisle SynTec Incorporated, USA, with over 40 years experience join hands to bring you the best waterproofing solutions. EPDM Roofing Systems 45 years ago, Carlisle pioneered single-ply roofing. Today, more than 12 billion square feet of membrane have been sold. No other manufacturer has a comparable track record. EPDM’s success is due to its many exceptional characteristics, including material longevity, weatherability and elasticity. These non-reinforced membranes are lightweight, easy to maneuver on the roof and offer optimal reroofing as well as new roofing solutions. Sure-Seal (black) EPDM (Ethylene Propylene Diene Monomer) nonreinforced membranes are available in standard 45-, 60- and 90-mil thicknesses. Membrane widths up to 50' and lengths to 200' which result in less rooftop seaming for large projects. Custom sizes may be requested. Fully-Adhered Systems utilizing EPDM require mechanical or adhesive attachment of the insulation and bonding of the membrane to the insulation with the recommended adhesive. Ballasted designs incorporate a loose-laid insulation and membrane and the use of ballast or pavers as securement. TPO MEMBRANE SYSTEMS Sure-Weld Thermoplastic Polyolefin (TPO) roof membranes are not adversely affected by most common materials and chemicals encountered in a roof environment.  Since the field seam is heat welded, it is as resistant to chemicals as the base sheet. The best course of action to take if unusual substances will contact the membrane, is to evaluate their effect on the membrane in the laboratory.  Carlisle SynTec's Laboratory is equipped to perform this testing, interpret the results, and provide a recommendation.  APP MEMBRANES STP has the largest range of Atactic Polypropylene modified bitumen membranes which include: Super Thermolay : It has a multilayered design consisting of a 160 gsm polyester core coated with APP (Atactic Polypropylene) modified bitumen and finally finished with thermo fusible polyethylene film. Aqua Shield : It has a multilayered design consisting of a 160 gsm fiberglass core coated with APP (Atactic Polypropylene) modified bitumen and finally finished with thermo fusible polyethylene film. Super Thermolay MT and Aqua Shield MT : These have mineral/slated finished as a top surface. Self Adhesive Membranes : It consists of self adhesive SBS (Styrene Butadiene Styrene) rubber/bitumen compound covered on the top side with high density cross laminated polyethylene film and on the underside with an easy-to-peel silicon film.

SEJ BOARDS SHALITEX EXPANSION JOINT BOARD is manufactured from water resistant, bitumen impregnated, cane fibre  Softboards. It is available in a wide range of sizes, both as boards & strips in thicknesses of 12mm, 18mm & 25mm. SHALITEX EXPANSION JOINT BOARD displays excellent resistnace to compression, with outstanding recovery characteristics. The boards are environment friendly as opposed to the environment destroying thermocole/plastic expansion joint boards. Softboard is usually made from bagasse. Bagasse is converted to pulp either by wet grinding on abrasive stone, rotating at high speed. Unwanted impurities are removed and several refining and screening stages are included in the manufacturing process to make the pulp thin and fine. The thin pulp produced by the above process is mixed with a small percentage of sizing additives and is fed on to a forming machine consisting mainly of a long conveyor belt.  Here most of the water is drained, sucked and pressed out of the pulp.  A continuous strip  of wet board so made is rolled to thickness cut into lengths and passed through the drying chambers.  The dried board thus coming out is the final softboard which is trimmed and cut into standard sizes.

SELF – LEVELLING EPOXIES Shali Deck SL - Three component system consisting of Comp A – Base Comp B –Hardener and Comp C - Filler Self – Levelling Shali Screed SL can be applied from thickness of 500 micron to 2000 micron. Suitable for floors where light, medium trolley movement, hospitals, kitchens, pharmaceuticals & automobile plants and work shops. EPOXY SCREED Shali Screed – Three component system consisting of Comp A – Base Comp B –Hardener and Comp C – Filler. It can be applied from thickness 3 mm to 5 mm. It is Ideal for floor where there is heavy trolley movement. Shali Screed 2000 – it’s a new product. Applied at a thickness of 2 mm. SELF – LEVELLING SCREED Shali Screed SL - Three component system consisting of Comp A – Base,   Comp B –Hardener and Comp C – Filler. Applied at a thickness of 2 mm to 4 mm. Ideal for heavy trolley movement areas Shali Screed SL UL Three component system consisting of Comp A – Base Comp B –Hardener and Comp C – Filler Applied at a thickness of 1.5 mm to 4 mm. It is applied as an under - layment. EPOXY COATINGS Epoxy coatings can be applied at thickness of 90 micron to 200 micron Shali Poxy LB â€“ Two Component System consisting of comp A- Base and comp B Hardener. It can be applied on the wall. Shali Poxy FC – Two Component System consisting of comp A-Base and comp B  Hardener. It can be applied on the floor as well as walls. Shaliol PU (Polyurethane Aliphatic based) – Two Component System consisting of comp A- Base and comp B Hardener. It is UV resistant and can be applied on the walls as well as on the floor.  PURPOSE OF ANTISTATIC FLOORING Antistatic flooring is done in the areas wherever static current is generated and requires to decipitate the charges, inorder to protect the electronic components like Integrated Circuit etc. Mainly applies for electronic manufacturing firms, Operation theaters, Companies which has installed sensitive equipments etc.

Coal Tar Enamel Plastisized Pitch is a coal tar based, hot-pour, pipe coating material prepared by digesting bituminous coal in a solution of pitch & high boiling coal tar distillate modified by inert material filler. This is generally known as Coal Tar Enamel in the coating industry.   Outerwrap STP Outerwrap is a reinforced glass fiber mat uniformly impregnated and coated with a Plasticised Pitch compatible material.   Coal Tar Tape Pipewrap is a hot applied coal tar tape system, especially suited for site-wrapping on water, gas and oil pipelines besides being one of the most effective solutions for refurbishment, repair and maintenance of existing pipelines.   COAL TAR EPOXY Shalipoxy CTE is a self-priming, two component coal tar epoxy thermo setanti-corrosive caoting system. Shalipoxy CTE is inexpensive and has considerably more llex (elongation) and bend when compared with other exposive. It withstands temprature and solvent. It provides excellent abrassion resistance, is black in color, and is used to protect steel, concrete, timber and other structures in corrosive enviroment arising out of their regular contact with water/ high moisture. Shalipoxy CTE has ability to bond with oil substances unlike other epoxies.

STP Limited, India, waterproofers to the nation since 1935 and Carlisle SynTec Incorporated, USA, with over 40 years experience join hands to bring you the best waterproofing solutions. EPDM Roofing Systems 45 years ago, Carlisle pioneered single-ply roofing. Today, more than 12 billion square feet of membrane have been sold. No other manufacturer has a comparable track record. EPDM’s success is due to its many exceptional characteristics, including material longevity, weatherability and elasticity. These non-reinforced membranes are lightweight, easy to maneuver on the roof and offer optimal reroofing as well as new roofing solutions. Sure-Seal (black) EPDM (Ethylene Propylene Diene Monomer) nonreinforced membranes are available in standard 45-, 60- and 90-mil thicknesses. Membrane widths up to 50' and lengths to 200' which result in less rooftop seaming for large projects. Custom sizes may be requested. Fully-Adhered Systems utilizing EPDM require mechanical or adhesive attachment of the insulation and bonding of the membrane to the insulation with the recommended adhesive. Ballasted designs incorporate a loose-laid insulation and membrane and the use of ballast or pavers as securement. TPO MEMBRANE SYSTEMS Sure-Weld Thermoplastic Polyolefin (TPO) roof membranes are not adversely affected by most common materials and chemicals encountered in a roof environment.  Since the field seam is heat welded, it is as resistant to chemicals as the base sheet. The best course of action to take if unusual substances will contact the membrane, is to evaluate their effect on the membrane in the laboratory.  Carlisle SynTec's Laboratory is equipped to perform this testing, interpret the results, and provide a recommendation.  APP MEMBRANES STP has the largest range of Atactic Polypropylene modified bitumen membranes which include: Super Thermolay : It has a multilayered design consisting of a 160 gsm polyester core coated with APP (Atactic Polypropylene) modified bitumen and finally finished with thermo fusible polyethylene film. Aqua Shield : It has a multilayered design consisting of a 160 gsm fiberglass core coated with APP (Atactic Polypropylene) modified bitumen and finally finished with thermo fusible polyethylene film. Super Thermolay MT and Aqua Shield MT : These have mineral/slated finished as a top surface. Self Adhesive Membranes : It consists of self adhesive SBS (Styrene Butadiene Styrene) rubber/bitumen compound covered on the top side with high density cross laminated polyethylene film and on the underside with an easy-to-peel silicon film.

SEJ BOARDS SHALITEX EXPANSION JOINT BOARD is manufactured from water resistant, bitumen impregnated, cane fibre  Softboards. It is available in a wide range of sizes, both as boards & strips in thicknesses of 12mm, 18mm & 25mm. SHALITEX EXPANSION JOINT BOARD displays excellent resistnace to compression, with outstanding recovery characteristics. The boards are environment friendly as opposed to the environment destroying thermocole/plastic expansion joint boards. Softboard is usually made from bagasse. Bagasse is converted to pulp either by wet grinding on abrasive stone, rotating at high speed. Unwanted impurities are removed and several refining and screening stages are included in the manufacturing process to make the pulp thin and fine. The thin pulp produced by the above process is mixed with a small percentage of sizing additives and is fed on to a forming machine consisting mainly of a long conveyor belt.  Here most of the water is drained, sucked and pressed out of the pulp.  A continuous strip  of wet board so made is rolled to thickness cut into lengths and passed through the drying chambers.  The dried board thus coming out is the final softboard which is trimmed and cut into standard sizes.

SELF – LEVELLING EPOXIES Shali Deck SL - Three component system consisting of Comp A – Base Comp B –Hardener and Comp C - Filler Self – Levelling Shali Screed SL can be applied from thickness of 500 micron to 2000 micron. Suitable for floors where light, medium trolley movement, hospitals, kitchens, pharmaceuticals & automobile plants and work shops. EPOXY SCREED Shali Screed – Three component system consisting of Comp A – Base Comp B –Hardener and Comp C – Filler. It can be applied from thickness 3 mm to 5 mm. It is Ideal for floor where there is heavy trolley movement. Shali Screed 2000 – it’s a new product. Applied at a thickness of 2 mm. SELF – LEVELLING SCREED Shali Screed SL - Three component system consisting of Comp A – Base,   Comp B –Hardener and Comp C – Filler. Applied at a thickness of 2 mm to 4 mm. Ideal for heavy trolley movement areas Shali Screed SL UL Three component system consisting of Comp A – Base Comp B –Hardener and Comp C – Filler Applied at a thickness of 1.5 mm to 4 mm. It is applied as an under - layment. EPOXY COATINGS Epoxy coatings can be applied at thickness of 90 micron to 200 micron Shali Poxy LB â€“ Two Component System consisting of comp A- Base and comp B Hardener. It can be applied on the wall. Shali Poxy FC – Two Component System consisting of comp A-Base and comp B  Hardener. It can be applied on the floor as well as walls. Shaliol PU (Polyurethane Aliphatic based) – Two Component System consisting of comp A- Base and comp B Hardener. It is UV resistant and can be applied on the walls as well as on the floor.  PURPOSE OF ANTISTATIC FLOORING Antistatic flooring is done in the areas wherever static current is generated and requires to decipitate the charges, inorder to protect the electronic components like Integrated Circuit etc. Mainly applies for electronic manufacturing firms, Operation theaters, Companies which has installed sensitive equipments etc.

Coal Tar Enamel Plastisized Pitch is a coal tar based, hot-pour, pipe coating material prepared by digesting bituminous coal in a solution of pitch & high boiling coal tar distillate modified by inert material filler. This is generally known as Coal Tar Enamel in the coating industry.   Outerwrap STP Outerwrap is a reinforced glass fiber mat uniformly impregnated and coated with a Plasticised Pitch compatible material.   Coal Tar Tape Pipewrap is a hot applied coal tar tape system, especially suited for site-wrapping on water, gas and oil pipelines besides being one of the most effective solutions for refurbishment, repair and maintenance of existing pipelines.   COAL TAR EPOXY Shalipoxy CTE is a self-priming, two component coal tar epoxy thermo setanti-corrosive caoting system. Shalipoxy CTE is inexpensive and has considerably more llex (elongation) and bend when compared with other exposive. It withstands temprature and solvent. It provides excellent abrassion resistance, is black in color, and is used to protect steel, concrete, timber and other structures in corrosive enviroment arising out of their regular contact with water/ high moisture. Shalipoxy CTE has ability to bond with oil substances unlike other epoxies.