T.M. ENGINEERING EQUIPMENTS

BBD Bag, Kolkata, West Bengal

Applications

Van Beest offers a wide range of sleeves, in both aluminium and carbon steel.

Range

Aluminium wire rope sleeves are manufactured according to DIN 3093 A. For safety in fabrication and application our sleeves are of seamless construction corresponding with the requirements of DIN 3093 A regarding material composition and mechanical properties.

Prescon carbon steel sleeves are manufactured from carbon steel and feature the Swaging Verification System in which the colour changes intensity after swaging. This system helps the sling manufacturer to determine whether or not the sleeve has been pressed.

The sleeves are of seamless construction and fit industry standard dies.

Design

Aluminium sleeves are self coloured.

The smaller dimensions of Prescon sleeves, up to and including 16 mm, are colour coded, larger dimensions are self coloured.

Applications

Shackles are used in lifting and static systems as removable links to connect (steel) wire rope, chain and other fittings. Screw pin shackles are used mainly for non-permanent applications. Safety bolt shackles are used for long-term or permanent applications or where the load may slide on the pin causing rotation of the pin. Chain or dee shackles are mainly used on one-leg systems whereas anchor or bow shackles are mainly used on multi-leg systems.

Range

Van Beest offers a wide range of bow and dee shackles, depending on the application on which the shackle is going to be used; the range stretches from Working Load Limit (WLL) 0.33 tons to 1500 tons. Therefore, our customers have a very extensive range to choose the shackle exactly suitable for the application. Most of the shackles

are directly available from stock. Furthermore, shackles can be supplied to many standards such as the US Federal Specification RR-C-271, EN 13889, British Standard 3032, DIN 82101, DIN 82016 etc.

Polar shackles are for use in extreme climatic conditions with material properties guaranteed up to temperatures of -40oC, and furthermore we offer a wide range of general commercial shackles, which are not suitable for lifting but merely for fixing purposes.

Applications

Van Beest offers a wide range of wire rope clips, specifically standardized models such as EN13411-5, US Federal Specification wire rope clips and DIN wire rope clips.

Range

The Green Pin wire rope clips are drop forged and have a bridge with grooves to fasten the wire rope properly in the clip; the DIN wire rope clips have a malleable base, without grooves.

Design

The finish is either electro-galvanized or hot dipped galvanized, unless otherwise specified.

Finish

Upon request, all wire rope clips can be supplied with a works certificate.

Applications

Thimbles are used to protect steel wire rope, fibre rope or synthetic rope. They are available in various models and sizes. All indicated types of thimbles can be used in combination with the above mentioned types of ropes.

Range

Van Beest offers a wide range of thimbles, from nationally standardized models to all types of commercially available thimbles.

Design

Thimbles can be cold-rolled, hot-rolled or die-cast, depending on the specific use of the thimbles.

Finish

The finish is either self coloured, painted, electro-galvanized or hot dipped galvanized.

Certification

Upon request, all thimbles can be supplied with a works certificate.

Instructions for use

It is required that the thimbles are regularly inspected and the inspection should take place in accordance with the standards given in the country of use.

This is required because the products in use may be affected by wear, misuse, overloading with a consequence of deformation and/or alteration of the steel structure.

The dimensions of the thimbles must be so that the (wire) rope fits properly into the groove of the thimble.

The nominal size of the thimble is the diameter of the (wire) rope with which it is intended to be used.

For (wire) ropes of intermediate sizes, the next larger size of thimble must be used.

Applications

Eye bolts and eye nuts are used for lifting machines, appliances or any other objects which cannot be lifted by hand or by fork lift truck.

Range

Van Beest offers a wide range of lifting eye bolts and eye nuts, from M6 up to M100, with Working Load Limits from 0.07 t up to 40 t.

Larger sizes can be supplied on request.

Van Beest can also offer other types of eye bolts and nuts in grade 8 and stainless steel. Please see our Excel catalogue for more information.

Applications

Sockets are used to attach steel wire rope to a fixed point to which the socket is to be connected. This can be as an anchoring system for tubes or pipes, anchor wires of dredging material, anchor cables of oil platforms, towing cables or for fastening cables in construction purposes such as bridges, roof construction etc.

Sockets are the strongest steel wire rope end fitting and if they are assembled in the proper way they can meet at least the breaking strength of the steel wire rope. In the past melted zinc was poured into the sockets to attach the steel wire rope; nowadays suitable resins have been developed for this purpose.

RangeVan Beest offers a wide range of sockets, i.e.:

Closed spelter sockets;

Open spelter sockets;

Open wedge sockets;

Short bow sockets;

Open swage sockets;

Closed swage sockets.

Design

Green Pin open and closed spelter sockets and open wedge sockets are made from cast high tensile steel. These sockets carry the following markings:

socket number;

diameter wire rope in mm and inches;

manufacturers symbol;

batch number;

CE conformity code.

With shortbow sockets you save money in replacement costs by eliminating costly downtime.

Swage sockets are drop forged from special bar quality carbon steel C-1035 and spheroidized annealed to be suitable for cold swaging.

The BA bulb bar anchorhas been designed for attachment to bulb profiles, often found in ship compartments and engine rooms, to provide a semi-permanent lifting point.

The clamp can be quickly and easily attached via the screw type mechanism. The fabricated light weight design ensures a firm grip onto the bulb section. The unique large bow hook ring gives easy connection for all types of lifting machines.

hese container lifting lugs are supplied in sets of 4 and are available in with a total lifting capacity of up to 56 tonnes. The CLT and CLB lugs serve as flexible lashing points for the transportation of containers.

Two types are available dependant on if you want to fasten them to the top or the side of the container:

The CLT type is vertically mounted in the hole at the top of the container and is locked into place by simply turning the lug 900. This configuration allows for transportation via the use of a lifting frame in conjunction with cables, chains or slings.

The CLB model is mounted horizontally to the side of the container at either the top or the bottom fixing holes. This model has a spring loaded bolt to prevent accidental release.

Three-leg chain sling with three self-tightening grips. For the transport of upright concrete pipes and concrete tubing rings, as well as for pipe-laying. Leaflet with details available. Avoid skewed lifting may not be used as two-leg sling. Observe load capacity does not correspond to grade 10.

User information:Before using the product the user information must be read and understood.
Assembling directive:

Self-declaration:

CAD Files:Files for using in 3D or 2D drawing programmes.The parts dimensionally correspond to the catalogue values. The drawings are maintained only periodically. Theres no guarantee for actuality. For damages and secondary damages because of drawings which are not up to date no liability is assumed.

According to EN 1677-1 with increased load capacity

Connecting link for pewag connex system

Load pin and collar CBH are also separately available.

Connecting link for: Master link chain Chain chain Hook chain

The CY plate clamps with hinged hook rings can be used for the safe handling of plate at various angles. It can lift plate from the horizontal and put down in the vertical. The hinged hook ring ensures adequate gripping pressure in every position, but the load capacity is reduced as seen in the diagram below showing the load / force capacities.

The main benefit of the CY hinged plate clamps is that longer plates can be lifted or handled, using two clamps on a two legged chain sling (as shown in illustration), thus eliminating the need for a spreader beam.

NB: The plate surface of the material must have a hardness level below HRC 30/Brinell 300.

EN 1677-1 with increased load capacity

For pewag clevis system

Suitable for simple and fast hooking and removal.

Only for applications without safety catch requirement.

EN 818-2 with increased load capacity

The high duty chain in grade 10

Round steel chains for use in lifting or lashing chainsMaximum working temperature: 380 CStandard surface: bluePlease consider the user information.