Star Impex International

KINGSTON UPON THAMES, United Kingdom

These are probably the most common type of bearing. They are found in everything from electric motors to hard drives. They can handle both radial and thrust loads, and are usually found in applications where the load is relatively small.

The high flow capacity coupled with being very simple to mechanise makes ball valves ideal for many applications where an openclose facility is required but not regulating of flow.

Metallic gaskets are intended for use in high-pressure environments, where joint integrity is essential. Applications include oil and gas upstream, high temperature reactors and high-pressure heat exchangers.

Piston pumps are in-line, variable displacement units and are available in variable sizes. In our range of Axial Piston Pumps, we stock the following: PVQ Series, 210 bar PVH Series, 250 bar PVM Series, 280 bar

Rotary seals are designed to seal applications that rotate. We offer the following rotary seals: Elastomeric Oil Rotary Seals NBR HNBR Viton Silicon Fabric-Reinforced Rubber Seals Split Rotary Seals V-Rings PTFE Rotary Seals

Flexible Ducting Flexible Ducting is predominantly used for such industry sectors as Automotive, aquatics and industrial ventilation.

We offer pressure seals. Pressure seals are used when it is necessary to keep the transmitter isolated from the process. A sealed system is used for a process fluid that is corrosive, viscous, subject to extreme temperature, toxic, sanitary or tends to collect and solidify. We offer the following seal types: composite seals piston seals polyurethane u rings single acting for piston and rods spring energised seals u packing (lip seals)

Mechanical seals are engineered for most pumps, mixer and agitator applications in maintenance. In many cases the designs have been proven to be workhorses over years of use. We stock the following seals: Axle Seal Range Bellows Seals Bespoke Sealing Solutions Cartridge Seals Easy fit Unitised Axle Seal General Sealing Products IMPAX and Fan Seals Mechanical Seal Design Mechanical Seal Manufacture Mechanical Seal Testing

Compression packing still provide users with gland sealing products that meet with today's demanding environmental and financial constraints.

We offer Non Metallic Gasket. Non-metallic gaskets are used across industries of all types to seal against low-pressure steam, hydrocarbons and their derivatives, strong organic acids, foodstuffs and similar.

We offer semi metallic gasket. Semi-metallic gaskets are designed for medium and high-pressure applications, and offer a high degree of safety.

Butterfly valves can be used for many applications either as openclose or simple regulating valves. A useful characteristic of butterfly valves is the availability of different lining materials which allows for uses ranging from non-aggressive media such as water or air through to chemicals and corrosive media.

Gate, globe and check valves are typically suitable for critical process applications.

Knife gate valves have widely been used in pulp or paper industry applications and for handling slurries but are also used in the offshore sector and are suitable for a wide range of wet or dry media.

These are used in applications like conveyer belt rollers, where they must hold heavy radial loads. In these bearings, the roller is a cylinder, so the contact between the inner and outer race is not a point but a line. This spreads the load out over a larger area, allowing the roller bearing to handle much greater loads than a ball bearing. However, this type of roller bearing is not designed to handle much thrust loading.

Needle Bearings are roller bearings with cylindrical rollers which are thin and long in relation to their diameter. They are referred to as Needle Rollers. In spite of their low cross section, the bearings have a high load carrying capacity and are thus eminently suitable for bearing arrangements where radial space is limited.

Plastic Bearings include conveyor and end cap bearings, skate wheels, radial bearings, pulleys and thrust races. The core feature of every plastic bearing product is the rolling element bearing.

Rod Ends are compact self-aligning spherical bushings that can support a large radial load and a bi-directional axial load at the same time.

Taper bearings have tapered inner and outer ring raceways between which tapered rollers are arranged. Taper roller design makes them particularly suitable for the accommodation of combined (radial and axial) loads.

The gearbox range provides for both motorised and input shaft assemblies in several configurations these being: In-Line Helical M Series Gearbox Helical Offset F Series Gearbox Helical Worm C Series Gearbox Bevel Helical K Series Gearbox Cyclo Drive 6000 Gearbox Power Plus Shaft Mounted Speed Reducer Gearbox