Concrete Etching Agent (Ultra Cleaner) is a composition of acid base material, inhibitors of corrosion and dispersing agents. Basically, Concrete Etching Agent (Ultra Cleaner) is a bluish liquid. The company makes Concrete Etching Agent (Ultra Cleaner) at competitive prices in the market. Advantages Safe with metals, wood, glass, plastic and rubber No corrosive action Penetrates oil and grease Uses For the removal of hardened concrete from tools, machinery and equipment, or rust and mill scale from steelwork. For the removal of mortar and plaster runs, droppings and stains from brickwork and concrete surfaces Suitable for etching of concrete floors and surfaces prior to application surface coatings Properties Appearance : Bluish liquid Specific gravity : 1.075+0.002 Application Instructions Cleaning brickwork A tiny trial area should be cleaned first to determine the most suitable Ultra cleaner cleaning agent dilution. Pre-wet the brick-work, and rub the affected areas, using a sponge, with a solution of Ultracleaner cleaning agent and water. Strength of the solution required will vary but should be between 1:1 and 1:4 (by volume of Ultracleaner cleaning agent to water). Immediately wash down thoroughly with clean water when the action was finished. The Large Equipment Cleaning (Barrows, concrete mixers, Readymix trucks, etc.) Ultra cleaner cleaning agent should be liberally applied to the deposits by a soft broom and allowed to soak overnight if possible. If the surfaces of the deposit can be cracked by mechanical means, it will speed up the operation. In many cases more than one application may be required. On final stage, dissolved deposits and loose material should be wire brushed and washed away with clean water. Small Tools Cleaning Use Ultra cleaner with a dipping method The tools should be soaked in one night, then taken out and washed with clean water to remove all loosely adhering materials. Care should be taken to avoid prolonged contact between Ultracleaner and zinc or aluminium parts of tools like rivets, etc. Concrete Floors Cleaning Pre-wet floors and then, using a stiff bristle broom, brush the affected areas with a solution of Ultracleaner and water. Strength of the solution required will vary but should be between 1:1 and 1:4 (Ultracleaner cleaning agent to water) Immediately wash down thoroughly with clean water Removal Of Rust And Mill Scale Pre-wet the floors and then, using a stiff bristle broom, brush the affected areas with a solution of Ultracleaners and water. Strength of the solution required will vary but should be between 1:1 and 1:4 (ultra-cleaner to water). When the action has finished, wash down thoroughly with clean water. Wire brush again to remove remaining loose material and finish by thoroughly washing down with clean water. Repeat if necessary. High degree of rust or scale can be removed by soaking in the Ultracleaner solutions for 1 hour. Etching concrete floors For etching surfaces to remove laitance and give a mechanical key before applying resin or other coating, Ultracleaner cleaning agent should be diluted with water and applied at the rate of approximately 1 liter per 2 sq. meters. The dilution will depend upon the condition of the floors and the degree of etching required, but normally it will be between 1:2 and 1:4. When the action has finished, wash down thoroughly with clean water. Note : As treatment with Ultracleaner can alter the surface finish of concrete, the minimum concentration necessary for effective removal of stains should be employed. The surface should be washed down with water immediately after the treatment is complete. Packing ( in barrels) 1 liter 5 liters 20 liters 200 liters Shelf life : At least 1 year in original sealed containers under normal warehouse conditions Precautions Health & Safety Ultracleaner cleaning agent is acid based and should be handled with care. It attacks zinc, aluminium and putty. If in doubt about its effect on a material, test a small area before application. Avoid contact with skin. Rubber gloves and goggles should be worn. Wash spillages with plenty of water. Enclosed areas should be well ventilated. If contact with eyes occurs, wash immediately with water and seek medical advice. Fire : Ultra cleaner is non-flammable. Additional Information Technical data and guidance can be provided on a wide range of admixtures, concreting aids, grouts, repairs and the range of industrial flooring systems which includes nonmetallic floor hardeners, epoxy floor coatings and self-leveling floor toppings, epoxy heavy duty abrasion resistant screeds. Separate data sheets are available on these products.
Sipcot, Ranipet, Tamil Nadu 
Write a Review
