Other Products / Services #438931

Elastomeric Waterproof Coating (Ultra Cote- 2P) is a two-component acrylic modified cementitous coating to waterproof and resurface concrete & masonry. Elastomeric Waterproof Coating (Ultra Cote- 2P) is simply applied by stiff brush, roller or trowel to form a waterproof flexible coating. Elastomeric Waterproof Coating (Ultra Cote- 2P) provides an affective barrier to waterborne salts and atmospheric gases. Fluid applied Elastomeric Waterproof Coating (Ultra Cote- 2P) provides hard-wearing, seamless waterproof membrane for roofs& foundation protection. Applications

• As a waterproof lining for water-retaining structure
• For coating seawater channels
• To provide foundation protection
• As a waterproof coating for roofs
• To protection the concrete surface from carbonation& chloride attacks

Advantages

• 1MM COATING PROVIDES anti-carbonation cover
• Resists up to 70 meter head pressure
• Excellent Bond strength
• Suitable for contact with drinking water
• Breathable & flexible coating
• Resistance to carbon dioxide and chloride ion diffusion

Properties

• Pack A : Milky white liquid
• Pack B : Grey powder
• Mix Ratio : 2:1(B: A)
• Density : 1.8kg/m3
• Water penetration : Nil 7 back at 2mm diff
• Coverage : 1.8 kg/m2/1mm

Packing : 15 kg ApplicationsIn Surface Preparation, removes all grease oil, dust particles. The surface should be free from any contaminant surface should be wet. DirectionsElastomeric Waterproof Coating (Ultra Cote- 2P) is pre-weighed and mixed using clean bucket. Do not add extra water. Apply the mixed material on a prepared wet surface using brush (or) roller. Apply the second coat after 3 hours of 1st coat. Storage : Keep in a cool & dry place Safety : Avoid contact with eyes, mouth, and skin. Splash water immediately if spilled.

Elastomeric Waterproof Coating (Ultra Cote-PUS) is a two-component acrylic modified cementitous coating to waterproof and resurface concrete & masonry. Elastomeric Waterproof Coating (Ultra Cote-PUS) is simply applied by stiff brush, roller or trowel to form a waterproof flexible coating. Elastomeric Waterproof Coating (Ultra Cote-PUS) provides an affective barrier to waterborne salts and atmospheric gases. Fluid applied Elastomeric Waterproof Coating (Ultra Cote-PUS) provides hard-wearing, seamless waterproof membrane for roofs& foundation protection. Applications

• As a waterproof lining for water-retaining structure
• For coating seawater channels
• To provide foundation protection
• As a waterproof coating for roofs
• To protection the concrete surface from carbonation& chloride attacks

Advantages

• 1MM coating provides anti-carbonation cover
• Resists up to 70 meter head pressure
• Excellent Bond strength
• Suitable for contact with drinking water
• Breathable & flexible coating
• Resistance to carbon dioxide and chloride ion diffusion

Properties

Pack-A : Milky white liquid

Pack B : Grey powder

Mix Ratio : 2:1(B: A)

Density : 1.8kg/m3

Water penetration : Nil 7 back at 2mm diff

Coverage : 1.8 kg/m2/1mm

Packing : 15 kg

Applications

• For surface preparation, removes all grease oil, dust particles.
• The surface should be free from any contaminant surface should be wet.
• Elastomeric Waterproof Coating (Ultra Cote-PUS) is pre-weighed and mixed using clean bucket. Do not add extra water.
• Apply the mixed material on a prepared wet surface using brush (or) roller.
• Apply the second coat after 3 hours of 1st coat.

Safety : Avoid contact with eyes, mouth, and skin. Splash water immediately if spilled. Storage : Keep in a cool & dry place.

Acrylic Polymer Waterproof Coating (Ultracrete-L) is an acrylic Polymer based waterproof coating. Acrylic Polymer Waterproof Coating (Ultracrete-L) is used for waterproofing of basements, toilets, terraces, roofs etc., general concrete repairs and protection of concrete against corrosion, salt attack. Features

• Combines a tough, hard-wearing surface with waterproofing
• Allows trapped vapors to escape without peeling and blistering
• Can be applied in uniform thickness to horizontal & vertical surface
• Develops excellent bond to most building materials
• Prevents salt penetration into concrete
• Highly durable in continuous wet condition

Surface Preparation

• The surface shall be cleaned to remove all dust, loose particles and free from oily surface. All concrete surfaces should be pre-wetted.
• Depressions are filled and leveled using Ultra Crete, cement & fillers

Application

• Acrylic Polymer Waterproof Coating (Ultracrete-L) is mixed with neat cement in the ratios of 2 part cement: 1 part polymer.
• The mix has to be stirred thoroughly without any lumps formation.
• The mix has to be applied by brush on a prepared surface.
• Two or more coats are recommended.
• Second coat should be applied by wetting the first coat.
• After 6 hours of application, moisture curing to be done for next 24 hours for 2 3 times.

Coverage : For slurry coats 1 1.2m² @ 0.4mm/2 coats Brush Topping

• Ultracrete : 0.5 Kg
• Cement : L 1.0 Kg (0.75 m²)
• Silica Sand 60/80 : 1.0 Kg

Note : Please consult or refer detailed individual application sheet for different waterproofing systems.

Integral Waterproofing Compound (Ultra Super) is a normal setting cement integral waterproofing compound with normal plasticizer in liquid form. The Integral Waterproofing Compound (Ultra Super) is a blend of specialized active ingredients to make concrete waterproof when there is permeability. Uses : Used in RCC / Concrete intended for water tank, roof deck, basement, lift pit. Features

• Permeability of concrete is improved.
• Due to increased cohesion, segregation and bleeding is reduced
• Improved workability
• Improved surface finish

Application : Add measured quantity to mixing water. Then add solution to the cement sand mix. Technical Data

• Color : Brown liquid
• S.G. : 1.06 0.02
• Chloride Content : 0.1%
• Dosage : 200 ml per 50 Kg Cement.

The company offers Liquid Alkali (Ultrashot- LAF). The Liquid Alkali (Ultrashot- LAF) is a concrete admixture based on liquid free accelerator. The Liquid Alkali (Ultrashot- LAF), offered by the company, has an excellent accelerating property. Added to that, the Liquid Alkali (Ultrashot- LAF) has numerous uses as well as features. Uses : Can be used to either produce a workable flowing concrete without loss or strength to enable reduction to be made which results in a dense, water light concrete with higher, easy and ultimate strength. Advantages

• Improved workability
• High early strength
• Improved durability
• Bond strength of concrete to reinforcement is increased
• Reduces corrosion of embedded steel.
• Increased compressive strength

Technical Data

• Form : Straw color liquid
• S.G. : 1.35 0.05
• Chloride content : NIL
• Compatibility : Can be used with all types of cement.
• Method of use : Mixed with gauging water and then added into concrete mix.
• Dosage : Max 7 % by weight of cement.
• Packing : 250 by Drum
• Storage : Store in a normal ambient

Non Shrink Grout (Ultra Grout-50-70) is a non-shrink, non-ferrous grout that is easily mixed for grouting at any consistency i.e. dry-pack, plastic or pourable. Non Shrink Grout (Ultra Grout-50-70) does not contain any iron particles, chlorides or gypsum and will not corrode, shrink, rust or ravel even under constant moist conditions. When mixed according to instructions, it produces a high compressive strength due to a technology that reduces the water-cement ratio. Benefits

• Retain its workability for 2 hours.
• Ready to use, just addition of water is required.
• High density, increases bond to metal, wool and other construction materials
• Will not rust, bleed.
• Requires no special treatment.
• Clean finish
• Density increases wear ability, permeability withstand heat & thermal shock.
• Water tight, resist freeze & thaw water conditions and salt penetration.
• Resists a variety of oils & Chemicals
• Contains no free lime will not produce efflorescence.

ApplicationsUltra Grout is recommended for grouting the following.

• Heavy equipped & machinery bases
• Structural columns
• Pump & equipment bases
• Power Line stations.
• Pre-case Tee joints
• Re-pointing mortar joints
• Structural cracks
• Bearing Plates
• Rail posts, seating bolts
• Post tensioned cables
• Patching

Water Requirements

• Plastic : 0.14
• Flowable mix : 0.16
• Fluid mix : 0.18

Mixing and ProportionsAdd required water to get consistency. For uniform mix, use paddle or drum type mechanical mixers. Do not mix more than 5 minutes. Place grout after mixing. The working time of grout is 2 hours. Surface EntrapmentsFirst remove all dust, oil, grease or contaminants from surfaces to be grouted, and then remove all loose material. Metals which will come in contact with grout must be derusted or freed of paints, oils & greases. To avoid entrapment of air, provide air relief openings where required. Prior to placement of grout, thoroughly soak or dampen all concrete areas to be grouted. Then remove excess water from voids & holes. FormingFor machinery bases and column base flats, follow standard forming procedures, which permit complete and proper placement of fluid grout, including use of head forms. All support elements should be anchored to prevent movements. Do not remove supports until grout has sufficiently hardened. Wool surfaces, which absorb moisture, should be pretreated with forming oils. SpecificationsUltra grout needs the following:

• ASTMC_1107 Standard Spec
• For packaged dry, hydraulic cement grout ( Non-shrink)
• CRD-C 621-89, specification for non-shrinking grout.
• CRD-C 614, method of test for time of setting of grout
• ASTM C 109 standard test method for compressive strength

Properties

• Appearance : Cementitious grey powder
• Wet density : 220020 Kg/m³
• Expansion : Min 1.0%
• Modules of elasticity : 4.5 x 10
• Packing : Available in 50 Kg HDPE Bags
• Shelf life : When stored in original, unopened pack, one year.

Concrete is the most versatile construction material and is widely used in a variety of constructions. However, along with correct composition and preparation it is essential to carry out proper curing of concrete in order to realize its advantages. A common method of curing such as, continuously spraying water on concrete surface and ponding etc. are inconvenient and also expensive. Evaporation of water from concrete will deprive it of its much needed water for hydration resulting in capillary-type pores, lower compressive strengths, chipping off on the surface and development of surface cracks. Liquid membrane-forming, concrete curing compound is based on the principle that concrete has enough water for uninterrupted hydration. Thus, the White Pigmented Curing Compound (Ultracure-WP) is an ideal option in such circumstances. The company offers the very best White Pigmented Curing Compound (Ultracure-WP) to the clients. the White Pigmented Curing Compound (Ultracure-WP) can be availed at the market leading prices. Scope

• Membrane-forming, ready to use, white colour emulsion of specially blended synthetic waxes, complying with ASTM C309-97
• For application on freshly cast concrete or newly exposed concrete surface after removal of formwork, to form a temporary membrane which will retain sufficient moisture for effective curing to take place.
• The membrane eventually break down and disintegrate after which the surface can be painted. It is used for concreting generally, but specially useful for large areas of concrete such as pavements, runways, bridge decks and industrial floors also for vertical or sloping surface as on chimneys, towers, silos, canal lining, columns and beams where water curing is difficult or unreliable.

Uses

• Single application-forms moisture barrier for whole of curing period.
• No other curing necessary-eliminates using of water, Hessian or sand completely.
• Reliable-no risk erratic or poor curing and ensures cement hydration efficiently.
• Ensures hard wearing surface-minimizes risk of drying shrinkage, cracks and dusty surface.
• Protection against a burning of the fresh concrete surface which is exposed to strong solar radiation, further protects concrete surface against influence of aggressive atmospheric conditions.
• Easy and safe application, non-toxic and non-inflammable
• Eco-friendly.

Application : Should be applied following the final finishing operation and immediately after the disappearance of water seen from concrete surface. It is important not to apply the product WP hen standing water is still present on concrete. If the concrete has already lost some of its surface water then it is recommended to fog down the surface before application of the product. Application Equipment : Low pressure spray, roller equipment most preferred and generally used is a knapsack sprayer of the type commonly used in horticulture or pest control while spraying, the distance between the sprayer and the concrete surface should be approximately 1m. Thus an uniform coating is guaranteed. It should be made sure that the spraying is properly carried out. Recommended SystemOne full coat until a continuous uniform film has been achieved

• Color : Bulk liquid-white Dry film-translucent
• Temperature : May be applied at temperatures range of 2^oC to 50^oC
• Flash Point : Not applicable
• Specific Gravity : 1.0 + 0.02
• Thinning : Not required
• Coverage/Dose Rate : 2.5 to 5.0 m²/Litre
• Drying time : Approx.90 min. at 30^oC
• Toxicity : Non-toxic

Testing : Exceeds requirements of ASTM C309-97 for moisture retention in liquid membrane curing compound. Packing : Available in 20 & 200 Litre plastic bucket/barrel. Product Information : Although the basic formulation of our products generally remains unchanged. Production refinements arising from continuing research and evaluation program may occasionally result in marginal changes in properties. Technical Service

• Maintains a technical division with highly qualified Technical Personnel to investigate and advise on subjects related to concrete and The Construction Industry. The Division provides advice on the correct use and selection of right products at the right place.
• Undertakes Consultancy Service for diagnosis and rehabilitation of distressed structures.
• Undertakes jobs as a package for total waterproofing system with guarantee.

Coal Tar Modified Epoxy (Ultrapoxy-CR) is a solvent free two pack high build Epoxy Resin System. Coal Tar Modified Epoxy (Ultrapoxy-CR) is specially designed for high chemical resistance coating for concrete structures. We make Coal Tar Modified Epoxy (Ultrapoxy-CR) available at the best prices in the market. Features / Advantages

• Solvent free and durable coating
• Can be easily applied by brush or roller
• Excellent adhesion
• Abrasion resistant
• High Chemical resistance over wide range of chemicals
• Can be applied to get a 250-300 microns thickness in two coats

Typical Applications

• For lining effluent tanks, chemical storage tanks
• Chemical resistant floor
• Walls of battery rooms & chemical industries
• Heavy oil spillage areas of chemical and mechanical industrial floors

Technical Details

• Solid content : 100%
• Mix ratio : 3:1 by weight
• Pot Life : 45 minutes at 30^oC
• Tack free time : About 4 to 6 hours at 30^oC.
• Initial cure : 24 hours at 30^oC.
• Full cure : 7 days at 30^oC.
• Over coating time : 24 hours

Directions For Use

• Surface PreparationThe surface has to be dry, sound & free from loose particles. This can be achieved by grit blasting or sand blasting or grinding and water jetting. The surface should not have moisture content of more than 4%. The surface should not contain any laitance, grease, oil or any other contamination.
• Mixing The pre-weighed ready to use components of Coal Tar Modified Epoxy (Ultrapoxy-CR) are mixed thoroughly with a mechanical stirrer with rpm of 300-350. The mixing should be done till it gets a homogenous color of the mixed material.

ApplicationsThe material is applied on the well prepared surface by a standard paintbrush, good quality lamb wool roller or sprayed with airless spray equipment. Care should be taken to ensure continuous film and proper material consumption. Coverage : The coverage will be 2.5- 3.5 m²/kg per coat Storage And Shelf Life : 1 year (Store the material at a cool and dry place at 25^oC) Cleaning Of Tools & Equipment : Clean with solvents Packing : 20Kg PrecautionsShould be applied with gloves and care should be taken to see that it does not fall on eyes. Splashes on to the skin have to be cleaned only with plenty of water only and medical advice has to be taken.

Coal Tar Modified Epoxy (Ultrapoxy-CTE) is a high build two pack waterproofing and anticorrosive system based upon epoxy resin, coal tar and amine curing agents. These agents in Coal Tar Modified Epoxy (Ultrapoxy-CTE) are specially chosen for their ability to withstand high degrees of corrosion and also for mild chemical attacks. We offer Coal Tar Modified Epoxy (Ultrapoxy-CTE) at the most competitive prices in the market. Features / Advantages

• Easily applicable by brush or trowel
• Seals localized cracks and surface porosity
• Bonds strongly to most of the building materials
• No primer is required
• Cures to a tough elastic waterproof film
• Excellent resistance to chemical aggression

Typical Applications

• Protective, waterproofing system for building roofs
• Anticorrosive coating for mild steel structures

Technical Information

• Nature : Two-component Liquid
• Color : Black
• Mixing ratio part by weight
• Part I (B) : 90
• Part II (H) : 10
• Solid content: Part I : 65%
• Pot life at 30^oC : 3 - 4 hours
• Initial hardness at 30^oC : 24 hours
• Full cure at 30^oC : 6 to 7 days
• Coverage : 30-35 sq. ft. / liter
• Recoat ability : 12 hours
• Below 20^oC these timings may be increased

Direction for use

• Surface Preparation : It is essential that Coal Tar Epoxy is applied to clean dry substrate in order to achieve maximum adhesion between the coating and substrate. All loose particles should be removed by brushing scraping or acid etching.
• Mixing : Coal Tar Epoxy is supplied in pre weighed packs which are ready to use on site. DO not add extra solvents or thinner, thorough mixing is essential.
• Cleaning : Tools and equipment can be cleaned immediately with solvents like xylene, acetone etc.
• Storage and Shelf Life : 12 months shelf life if stored below 35^oC and 50% R.H.

Packing

• 1 liter
• 5 liters
• 20 liters

Direction for use Bare Steel : All surfaces shall be free of rust, mill scale, and contaminants such as oil, grease, dirt, and salts. Before any surface preparation is attempted, oil and grease must be removed by employing SSPC- SP1 solvent cleaning. Precaution

• Danger!
• Flammable!
• Contains xylene
• Keep away from heat, sparks and flame.
• Avoid breathing vapor.
• Use with forced air ventilation in confined areas.
• Avoid contact of resin or hardener with skin or eyes.
• In case of eye contact, flush immediately with plenty of water and consult a physician.
• Do not take internally.
• Not to be applied when air and surface temperatures are below 50^oF
• Must be top coated with appropriate coating when used in corrosive environments
• Caution when opening containers- gassing may occur
• Not for immersion or for exposure to acids & alkalis without proper topcoats

Acrylic Polymer Cementitious Coating (Ultrafix) is an acrylic polymer based cementitious ready to use tile adhesive for ceramic, mosaic, marble and cement tiles. Acrylic Polymer Cementitious Coating (Ultrafix) can be applied in tile on tile form. We make Acrylic Polymer Cementitious Coating (Ultrafix) available at the best prices in the market. Features

• Excellent Bond Strength
• Longer pot life up to 2 hours
• Good Waterproofing
• Water curing and soaking is not required
• Fast laying of tiles that reduces labor cost
• Eco Friendly
• Tile fixing permanent

Technical Data

• Color : Grey
• Form : Dry Powder
• Bond Strength : More than 20 kg / m²
• Coverage : 1.8 m^o / 2mm / 6 Kg
• Water powder Ratio : 282%

Application

• Surface Preparation : The surface must be free form dust, grease and oil. No need to soak tiles.
• Mixing
  • Add 280 300 ml water by weight of Acrylic Polymer Cementitious Coating (Ultrafix) depending on the climatic condition.
  • Mix the powder to water until a uniform paste is obtained. Spread out the paste to a uniform thickness by notched trowel.
  • Place tiles firmly on Acrylic Polymer Cementitious Coating (Ultrafix) bed ensuring good contract with tile.

Packing (In HDPE bags)

• 20kg
• 50kg

Advantages Of Ultrafix Over Plain Cement Sand Mortar

• Thick bed is required (8-10mm) for plain mortar, where as thin bed is sufficient (2-3 mm) for CTA. (Cementitious Tile adhesive)
• Curing is required for plain mortar. In case of CTA no curing is required
• Adhesive strength of plain mortar is very less (less than 4kg/cm2). In case of CTA adhesive strength is around 10kg/cm2 i.e., 2-5 times higher than the normal mortar.
• Failure rate is nil in case of CTA when properly applied

Function Of Tile Adhesive

• Tile Adhesives are slightly flexible in nature.
• This flexibility accommodates the irregular expansion and contraction of two different types of materials, i.e., adhesive and tile. On the other hand conventional cement sand mortar or cement paste does not exhibit any flexibility. This results in delaminating of tiles from the concrete or plastered surface.

Concrete Etching Agent (Ultra Cleaner) is a composition of acid base material, inhibitors of corrosion and dispersing agents. Basically, Concrete Etching Agent (Ultra Cleaner) is a bluish liquid. The company makes Concrete Etching Agent (Ultra Cleaner) at competitive prices in the market. Advantages

• Safe with metals, wood, glass, plastic and rubber
• No corrosive action
• Penetrates oil and grease

Uses

• For the removal of hardened concrete from tools, machinery and equipment, or rust and mill scale from steelwork.
• For the removal of mortar and plaster runs, droppings and stains from brickwork and concrete surfaces
• Suitable for etching of concrete floors and surfaces prior to application surface coatings

Properties

• Appearance : Bluish liquid
• Specific gravity : 1.075+0.002

Application InstructionsCleaning brickwork

• A tiny trial area should be cleaned first to determine the most suitable Ultra cleaner cleaning agent dilution.
• Pre-wet the brick-work, and rub the affected areas, using a sponge, with a solution of Ultracleaner cleaning agent and water.
• Strength of the solution required will vary but should be between 1:1 and 1:4 (by volume of Ultracleaner cleaning agent to water).
• Immediately wash down thoroughly with clean water when the action was finished.

The Large Equipment Cleaning (Barrows, concrete mixers, Readymix trucks, etc.)

• Ultra cleaner cleaning agent should be liberally applied to the deposits by a soft broom and allowed to soak overnight if possible.
• If the surfaces of the deposit can be cracked by mechanical means, it will speed up the operation.
• In many cases more than one application may be required.
• On final stage, dissolved deposits and loose material should be wire brushed and washed away with clean water.

Small Tools Cleaning

• Use Ultra cleaner with a dipping method
• The tools should be soaked in one night, then taken out and washed with clean water to remove all loosely adhering materials.
• Care should be taken to avoid prolonged contact between Ultracleaner and zinc or aluminium parts of tools like rivets, etc.

Concrete Floors Cleaning

• Pre-wet floors and then, using a stiff bristle broom, brush the affected areas with a solution of Ultracleaner and water.
• Strength of the solution required will vary but should be between 1:1 and 1:4 (Ultracleaner cleaning agent to water)
• Immediately wash down thoroughly with clean water

Removal Of Rust And Mill Scale

• Pre-wet the floors and then, using a stiff bristle broom, brush the affected areas with a solution of Ultracleaners and water.
• Strength of the solution required will vary but should be between 1:1 and 1:4 (ultra-cleaner to water).
• When the action has finished, wash down thoroughly with clean water.
• Wire brush again to remove remaining loose material and finish by thoroughly washing down with clean water.
• Repeat if necessary.
• High degree of rust or scale can be removed by soaking in the Ultracleaner solutions for 1 hour.

Etching concrete floors

• For etching surfaces to remove laitance and give a mechanical key before applying resin or other coating, Ultracleaner cleaning agent should be diluted with water and applied at the rate of approximately 1 liter per 2 sq. meters.
• The dilution will depend upon the condition of the floors and the degree of etching required, but normally it will be between 1:2 and 1:4.
• When the action has finished, wash down thoroughly with clean water.

Note : As treatment with Ultracleaner can alter the surface finish of concrete, the minimum concentration necessary for effective removal of stains should be employed. The surface should be washed down with water immediately after the treatment is complete. Packing ( in barrels)

• 1 liter
• 5 liters
• 20 liters
• 200 liters

Shelf life : At least 1 year in original sealed containers under normal warehouse conditions Precautions

• Health & Safety
  • Ultracleaner cleaning agent is acid based and should be handled with care. It attacks zinc, aluminium and putty.
  • If in doubt about its effect on a material, test a small area before application.
  • Avoid contact with skin. Rubber gloves and goggles should be worn.
  • Wash spillages with plenty of water.
  • Enclosed areas should be well ventilated.
  • If contact with eyes occurs, wash immediately with water and seek medical advice.
• Fire : Ultra cleaner is non-flammable.

Additional Information

• Technical data and guidance can be provided on a wide range of admixtures, concreting aids, grouts, repairs and the range of industrial flooring systems which includes nonmetallic floor hardeners, epoxy floor coatings and self-leveling floor toppings, epoxy heavy duty abrasion resistant screeds.
• Separate data sheets are available on these products.

Epoxy Hardener (UH 930) is a formulated solvent-less, aromatic diamine-adduct curing agent of medium reactivity. Epoxy Hardener (UH 930) has practically no smells and cures well at room temperature with UEG990, UEM993, etc. The cured mass of Epoxy Hardener (UH 930) has excellent chemical resistance and climatic condition.

Epoxy Hardener (UH 950) is a formulated solvent-less, aromatic diamine-adduct curing agent of medium reactivity. Epoxy Hardener (UH 950) has practically no smells and cures well at room temperature with UEG990, UEM993, etc. The cured mass of Epoxy Hardener (UH 950) has excellent chemical resistance and climatic condition. Epoxy Hardener (UH 950) is similar to Epoxy Hardener (UH 930), but has markedly higher reactivity.

Floor Hardener (Ultrafloor-SOF) is a Ready-to-use, shake-on-floor Abrasion Resistant Floor hardener. Floor Hardener (Ultrafloor-SOF) is used for wearing surface for industrial floors. Floor Hardener (Ultrafloor-SOF) is recommended for factory floors and warehouse surfaces that require abrasion resistant floor. Features

• Wear resistance & high abrasion resistant floor surface.
• High impact resistance
• Increased surface density
• Increases to resistance
• Penetration by oil, grease, hydraulic fluids and many industrial chemicals

Application ProcedureBase concreting

• The base concrete should be sound and placed.
• The water: cement ratio should be kept to a minimum consistency by using ULTRAFLO- N to produce a fully compacted concrete without excess water coming to the surface.
• Care must be taken to level the surface throughout the trowelling operation.

Application

• Floor Hardener (Ultrafloor-SOF) should be sprinkled in two equal stages evenly on the surface of the freshly laid concrete as soon as the surface water has evaporated.
• Immediately after sprinkling of ULTRAFLOOR-SOF trowelling should be carried out either by hand or power float, when the surface has sufficiently stiffened as second trowel ling should be given to close any pores and remove any undulation in the surface.
• This should be followed by a final hand trowelling to remove any disc marks.
• The floor must be thoroughly cured.

CoverageCoverage varies on types of floors.

• Medium duty : 5 Kg/m²
• Heavy duty : 7 Kg/m²
• Extra Heavy duty : 9 Kg/m²

Packing : Available in 50 Kg HDPE Bags

Mineral Admixture (Ultra Tuff-MS) is a dry, compacted, silica fume based high performance product. The Mineral Admixture (Ultra Tuff-MS) is used to produce high quality concrete by reacting chemically within the concrete to increase the amount of calcium silicate hydrate gel formed. This way, the strength of the Mineral Admixture (Ultra Tuff-MS) is improved and the concrete is produced by filling the voids between cement particles. The reduced permeability of concrete produced with Mineral Admixture (Ultra Tuff-MS) greatly limits the ingress of chlorides, sulfates and aggressive chemicals promoting reinforcing at steel corrosion and open distresses in concrete. Advantages

• Improved durability and compressive strength
• Low permeability
• Freeze and their resistance
• Better Chemical resistance
• Better flexural strength
• Corrosion protection

Uses

• Basement structures.
• Parking decks.
• Bridge decks.
• Marine Structure.
• Pre-stressed concrete
• Precast concrete
• Ready Mix concrete

Direction for use : It is recommended to be used with a high range water reducer to provide better workability while maintaining the desired low water-cement ratio. Dosage : Used at the rate of 5-10% by weight of cement, depending in the amount of strength increase and impermeability required. Packing : 25 Kg HDPE Bags.

Polysulfide-Based Joint Sealant (Ultraseal-PS) is a two pack Polysulfide-Based Joint Sealant for vertical and inclined expansion/contraction joints. When two packs of Polysulfide-Based Joint Sealant (Ultraseal-PS) are mixed, it forms tough, flexible, durable rubber like material with strong adhesion properties on most building substrates and joints. Standards

• ASTM-C-920.
• BS-4254

Features

• Long lasting elasticity
• High movement capacity
• Excellent adhesion
• Good chemical and fuel resistance

Uses : Used to form long lasting weather resistance and waterproof seals in joints subject to regular movement. It is used in underpasses, tunnels, basements, pre-cast concrete elements, bridges, runways and rigid pavements. Surface preparation : All surface must be clean, dry and free from any loose particles, grease, or oils. Correct joint designs should be followed use primer on both inside surfaces of the joints. Joint Design

• Minimum joint depth- 8mm
• Maximum joint width 40mm
• Width to depth ratio up to 10mm 1:1
• For 10 to 40mm width : Depth ratio 2:1

Mixing : Mix both packs of sealants at the ratio of 92:8 by weight by paddle type mixture to a smooth uniform consistency place t he uniformly mixed sealant into the joints by tapping. Technical Data

• Pack A : White paste
• Pack B : Black paste
• Mix ratio : 92: 8
• Movement capacity : +25%
• Pot life : At 30^oC - to 6 hours
• Curing time : 21 days
• Density : 1550kg/cm3
• Shore : A hardness 20-25
• Service temperatures : Up to 80^oC
• Application temperature : 5 to 40^oC
• Shrinkage : Up to 0.5%
• Chemical resistance : Dilute acids, alkalis, ATF fuel, kerosene, diesel, petrol, lubricating oil, white spirit.
• Storage condition : Keep in a dry place and away from extremes of heat.
• Shelf life : One year if unopened
• Packing : 1 & 3 kgs

The company offers the very best Water Reducing Admixture (Ultraflo-S). the Water Reducing Admixture (Ultraflo-S) is a concrete admixture based on Sulphonated Naphthalene Formaldehyde Condensate and an organic polymer. The Water Reducing Admixture (Ultraflo-S) has excellent plasticizing property and conforms to the ASTM C-494; IS 9103 1999. Uses : Can be used to either produce an workable flowing concrete without loss or strength to enable large water reduction to be made for the same workability which results in a dense, water light concrete with higher, easy and ultimate strength. Advantages

• Improved workability
• Minimize shrinkage.
• Improved durability
• Bond strength of concrete to reinforcement is increased
• Reduces corrosion of embedded steel.
• Increased compressive strength
• Possible cement saving.

Technical Data

• Form : Brown colour liquid
• S.G. : 1.20 0.02
• Chloride content : NIL
• Compatibility : Can be used with all types of cement.
• Method of use : ULTRAFLO-S should be mixed with gauging water and then added into concrete mix.
• Dosage : Max 2% by weight of cement.
• Packing : 25 & 200 by Drum
• Storage : Store in a normal ambient tent.

The company is a well-known Manufacturer and Supplier of Anticorrosive Coating. The Ultra Epoxy UEM 993 Anticorrosive Coating is modified epoxy resin which can be suitably formulated with hardeners like UH930, UH950, UH941 or UH940 and applied as anti-corrosive solvent-free coatings on surfaces. The Anticorrosive Coating is ideal where protection against corrosive environment is of prime importance. To name a few field of applications, the Anticorrosive Coatings are used on steel and concrete structures in chemical plants, oil refineries, marine installation, food factories, paper mill, civil structures, bridges, dams, lock gates, canal bottoms and banks, internal and external surfaces of steel or asbestos pipes storage tanks, reaction vessels and others. The solvent-less Anticorrosive Coatings can be applied by conventional brushings and trowel ling methods. In general, two Anticorrosive Coatings are applied: the first Anticorrosive Coating being the primer coat and the second being the top coat, However, the number of coats can be increased, depending upon the degree of abuse the surface is exposed to. Information On Processing

• Preparation Of SurfaceThe preparation of surface over which the Anticorrosive Coating is to be applied is of primary importance for achieving the most optimum surface for better adhesion of the coating. If the surface is metallic it can be sand blasted or roughened with emery paper. The surface must be thoroughly cleaned and should be devoid cleaning may be done with solvents like tri-choroethlyene, carbon tetra chloride, toluene etc. Incase the concrete surface is too smooth, it can be roughened by treatment with dilute hydrochloric acid and followed by thorough washing with plenty of water till the washing is neutral top litmus. The surface then may be dried before application of coating.
• Mixing Ratio
  • Primer Coat
    • Ultra Epoxy UEM 993 : 100 parts by weight
    • Hardener UH 941 : 80 party by weight Or
    • Ultra Epoxy UEM 993: 100 parts by weight
    • Hardener UH940: 50parts by weight
    The Resin and the Hardener can be mixed in a container manually till homogenous state is reached. The mix then can be applied as primer coat.
  • Top CoatIn preparation of the top coat, different rate of cure may be achieved with Ultra Epoxy UEM 993/ UH930/ UH950. Typical 3 ratios are indicated below as a guideline. Depending upon the actual requirement at the time of application, suitable proportions may be used. The first 2 mixing ratios are normally being used. Apart from the resin and hardener composition, some fillers like silica flour (250 mesh) can be used. In case of the coating being applied on a vertical surface, a thixotropic agent like IF9 Can be added in the mix to the tune of 5phr and thoroughly homogenized before application.
• ApplicationAfter the surface is prepared, the primer coat van be applied by brushing or trowel ling as may be found suitable, up to a required thickness of coat. After the primer coat is applied, it may be allowed to stand at room temperature, till such time the coating becomes tacky to tough. At this stage, the top coat may be applied by brushing or trowel ling. In case, the primer coat has gelled into a hard mass, the surface may be lightly abraded with a sand paper and then the top coat may be applied. After the coating has gelled, it will take about 7 to 8 day to room temperature to attain the full cure. Such a Coating will exhibit very strong bond on to the surface and resistance against a wide range to chemicals. The heat distortion temperature of this system is slightly above 80*c.
• Coverage1 kg of the mix of the above formulations will cover approximately 2 to 3 sq.m of the surface for a thickness of about 300 to 400 microns. However, the coverage will vary depending upon the porosity and degree of roughness of the surface.