Our Products
Application
Application Method | Brush/Roller | Air Spray | Airless Spray |
---|---|---|---|
Recommended thinner | T � 111/T-222 | T � 111/T-222 | T-222T/ � 111 |
Volume of thinner | 0 � 5% | 5 � 10% | 0 � 5% |
Nozzle orifice | 1.5 � 3.00 mm | 0.28 � 0.33 mm | |
Nozzle pressure | 0.3 � 0.4 Mpa (=approx. 3 � 4 atm, 43 � 57 p.s.i.) | 15 Mpa (=approx. 150 atm, 2100 p.s.i.) |
Technical Data
Colour | Range |
---|---|
Gloss | Eggshell |
Volume Solids | Approx. 40% |
Recommended DFT/Coat | 25 - 35 microns |
Theoretical covering capacity | 16.0 sq.mtr/ | @ 25 microns DFT 11.4 sq.mtr/ | @ 35 microns DFT |
Flash point | Base : not less than 24oC Hardener : Not less than 24oC |
Drying time at 30oC | Surface dry :1 hour Hard dry : 16 hours Full cure : 7days |
Over coating Interval at 30oC | Min. : 16 hours Max.: 5 days, provided surface is free from all contamination. |
Shelf Life (cool and dry place) | At least 12 months |
Note : As common to all epoxy, the product will chalk and discolor on exterior exposure. However these phenomenon are not detrimental to anti-corrosive performance. |
Apply Top-coats As Follows :
Product | Thinner | Dilution % (by vol) | Application Viscosity (sec) | Recoating* period (hrs) |
---|---|---|---|---|
Sand with Emery Paper 180 and wipe clean. | ||||
Uniprime Wood primer/Meta primer/ Wall primer. (select primer depending on surface) Brush, Roller, Spray | MTO (Mineral Turpentine oil) | 8 -10 12 -15 | 30 - 10 20 - 25 | 6-8 hrs. |
Unicare Wall Putty for masonary/cement surfaces or Unique Paints Knifing Paste Filler for wood/ metal surface Knifing with putty blade. | Water or MTO (Mineral Turpentine oil) | As reqd. | As reqd. | Wall Putty 4-6 hrs. Knifing Paste Filler 6-8 hrs. |
Sand with Emery Paper 180 and wipe clean. | ||||
Uniprime Wood primer/Meta primer/ Wall primer. (select primer depending on surface) Brush, Roller, Spray | MTO (Mineral Turpentine oil) | 8 -10 12 - 15 | 30 - 40 20 - 25 | 6-8 hrs. |
Sand with Emery Paper 320 and wipe clean. | ||||
Uniprime Synthetic Enamel 1st Coat Brush, Roller, Spray | MTO (Mineral Turpentine oil) | 8 - 10 25-30 | 55 - 60 22 - 25 | 6-8 hrs. |
Uniprime Synthetic Enamel 2ndt Coat Brush, Roller, Spray | MTO (Mineral Turpentine oil) | 8 - 10 25-30 | 55 - 60 22 - 25 | 6-8 hrs. |
Recommended Application
Please refer Annexure for surface preparation ans apply 2-3 coats of Unicryl Acrylic Wall Putty as given below : | ||||
Product | Thinner | Dilution %(by vol) | Application Viscosity (sec) | Recoating* period (hrs) |
---|---|---|---|---|
Unicryl Acrylic Wall Putty 1st coat Putty Knife | Water (if required) | Paste | 4-6 hrs | |
Unicryl Acrylic Wall Putty 2nd coat Putty Knife | Water (if required) | Paste | 4-6 hrs |
Apply Top-coats Of Unilite Distemper As Follows :
Product | Thinner | Dilution % (by vol) | Application Viscosity (sec) | Recoating* period (hrs) |
---|---|---|---|---|
Sand with Emery Paper 180 and wipe clean. | ||||
Uniprime Wall primer (WB / SB) Brush, Roller, Spray | Water or MTO (Mineral Turpentine oil) | 8 -10 12 - 15 | 30 â- 40 20- 25 | 6-8 hrs. |
Unicare Wall Putty Knifing with putty blade. | Water | Small amounts to improve flowability. | NA. | 4-6 hrs. |
Sand with Emery Paper 180 and wipe clean. | ||||
Uniprime Wall primer (WB / SB) Brush, Roller, Spray | Water or MTO (Mineral Turpentine oil) | 8 - 10 12 - 15 | 30 - 40 | 6-8 hrs. |
Sand with Emery Paper 320 and wipe clean. | ||||
Unilite Acrylic Washable Distemper 1st Coat Brush, Roller, Spray | Water | 55 - 60 50 55 | 20 - 25 25 - 35 | 3-4 hrs. |
Unilite Acrylic Washable Distemper 2nd Coat Brush, Roller, Spray | Water | 55 â- 60 50 55 | 20 - 25 25 - 35 | 3-4 hrs. |
Recommended Application Cleaning : Prepare the surface be sanding with Emery Paper 180. Wipe clean. Apply topcoats as follows : | ||||
Product | Thinner | Dilution % (by vol) | Application Viscosity (sec) | Recoating* period (hrs) |
---|---|---|---|---|
Uniprime Wall Base Primer 1st Coat | Water | 100 | 20-22 | 4-6 hrs |
Brushing | ||||
Putty (Optional) Smoothen the surface by filling dents with thin coats of Unicryl Acrylic Putty. Allow it to dry for 4-6 hours. Sand lightly with Emery Paper 180 and wipe clean | ||||
Uniprime Wall Base primer 2nd Coat Brushing on puttied areas | Water | 100 | 20-22 | 4-6 hrs |