JADCO

United States

• Series6 Coupling 100 Cfm Breather Box

The Breather Box™ is a portable Grade-D filtration system designed to provide breathing air for a specific number of workers. The system filters incoming air from a compressor to provide ­respirator users with Grade-D quality air and ­monitors for CO andor Oxygen. The first stage element filters bulk water and particulate and has an auto drain. The second stage coalescing filter eliminates atomized oils, mists, ultra-fine particulates, and has an auto drain. The third stage filter removes organic vapors and odors and has a manual drain. Filter change indicators are standard on all three stages of filtration. Filtration efficiency is 99.99% @ .01 micron. All Breather Boxes™ are designed to be used in the upright and closed position to prevent internal contamination. The standard carbon monoxide (CO) airline monitor operates on disposable 9-volt batteries, 8-16 volt DC, or 115 VAC for continuous air monitoring. An external audible alarm and light signals the workers of high CO content. A remote alarm jack is provided on all models except for Model BB15-CO. Point-of-Attachment (POA) boxes can extend respirator usage beyond 300 feet.

Standard Grade D Filtration Panel Reviews There are no reviews yet. Be the first to review “Standard Grade D Filtration Panel” Your email address will not be published.

Product Description $3250.00 per month Includes Greener Blaster, 50 1 14″ Blast Hose, #8 Long Blast Nozzle and deadman controls Credit Card is required and a signed rental contract, Also front and back copy of credit card, Drivers License, and address of Jobsite

• Series300,000 BTU MTM Heater

•Heat Input BTUH: 293, 982 •Heat Output BTUH: 258, 704 •Fuel Consumption: US GALH 2.17 •Heated Airflow CFM: 2530 •Temperature Rise (@64°F) 126°F •Power Supply: 120V, 1 PH, 60 Hertz •Fan Motor Power: 1 HP (1700 RPM) •Current Rating AMPS: 11.80 •Max Length Flex Duct (1-Way): 75’ •Max Length Flex Duct (2-Way): 35’ •Flue Size: 6” •Tank Capacity: US GAL 27.7 •Run Time HOUR: 13 •Pre-Heated Oil Filter •No supervision required can be controlled by thermostat, humidistat or timer •1ft power cord •AISI 430 stainless steel combustion chamber with four-pass heat exchanger technology •Automatic post ventilation cycle to cool down the combustion chamber •Electronic flame control unit •Overheating thermostat (safety device turns off unit and requires a manual reset) •Fuel lines in hydrocarbon-resistant rubber wire-mesh protected •Bayonet-type fuel tank cap •Fuel tank drain plug •Electric control panel •Oil filter; pre-heated oil filter •Combustion air pressure switch (safety device turns off unit and requires a manual reset) •10” pneumatic wheels •Single Fuel Line Kit: This accessory allows the unit to recirculate hot oil from the return line back into •the filter. The hot oil in the filter eases restarts and increases the performance of the unit in extreme cold •temperature •Weight: 275lbs •Dimensions: 69” x 28” x 42”

• Series50CFM Filtration Breather Box

50cfm Filtration Breather Box. 50CFM Filtration Breather Box: Air Systems International & Breathing Filtration. These Portable Grade-d Filtration Systems Are Designed To Provide Breathing Air For A Specific Number Of Workers. The System Filters Inlet Air To Provide Respirator Users Grade-d Quality Air.. The Breather Box™ is a portable Grade-D filtration system designed to provide breathing air for a specific number of workers. The system filters incoming air from a compressor to provide ­respirator users with Grade-D quality air and ­monitors for CO andor Oxygen. The first stage element filters bulk water and particulate and has an auto drain. The second stage coalescing filter eliminates atomized oils, mists, ultra-fine particulates, and has an auto drain. The third stage filter removes organic vapors and odors and has a manual drain. Filter change indicators are standard on all three stages of filtration. Filtration efficiency is 99.99% @ .01 micron. All Breather Boxes™ are designed to be used in the upright and closed position to prevent internal contamination. The standard carbon monoxide (CO) airline monitor operates on disposable 9-volt batteries, 8-16 volt DC, or 115 VAC for continuous air monitoring. An external audible alarm and light signals the workers of high CO content. A remote alarm jack is provided on all models except for Model BB15-CO. Point-of-Attachment (POA) boxes can extend respirator usage beyond 300 feet.

• SeriesAir Systems BB-30

This portable Grade-D filtration systems is designed to provide breathing air for a specific number of workers. The system filters inlet air to provide respirator users Grade-D quality air. The first stage filters bulk water and particulate, second stage coalescing filter eliminates atomized oils, mists, and ultra-fine particulates, third stage removes organic vapors and odors. Filter change indicators are standard on all three stages. Filter efficiency is 99.99 percent.01 microns. A built-in carbon monoxide monitor operates on 9-volt DC, dual 8 – 16 volt DC or 115 VAC for continuous detection. An external alarm and light signals the worker of high CO content. Point-of-Attachment (POA) boxes can extend respirator usage beyond 300 feet. The Breather Box models is designed to be used in the closed position to prevent internal contamination. Solid aluminum block manifold. 0-160 psi Pressure Gauge. Flowmeter to verify air flow to monitor. Remote DC alarm jack with cover cap.

Harsco Recycled Glass 50lb Bags Medium Grit Product Description Harsco Recycled Glass Medium Grit Bag weight 50lbs

• SeriesCO91-14LAC Portable CO monitor

Product Description This portable airline monitor connects easily to a breathing air filtration source or ambient air pumps and monitors the air for CO content. The audible alarm (90dbA) and light will activate when the CO level exceeds 10ppm (5ppm Canadian). External alarm and lights allow for the unit to be used in the closed position and eliminates damage and contamination of the internal components.

Product Description Explosion Proof Brick Light with 150″ of cord Must purchase Covers Must have credit card to rent Must sign Rental contract Call for details

Clemco’s Wetblast Injector System adds the dust-suppressing power of water to any pressure blast machine. The Wetblast injects a small amount of water into the high-velocity abrasiveair stream just before the nozzle. This hard-hitting mixture of water and abrasive cleans and keeps dust levels under control. The Wetblast System introduces water into the abrasiveair stream before it passes through the nozzle orifice. This results in a complete wetting of each abrasive particle, unlike with water ring systems. The Wetblast controls airborne dust far better than water ring systems. Operation The power behind Clemco’s Wetblast Injector rests in our exclusive 10:1 pump. It uses compressed air to inject water into the high-velocity abrasiveair stream at the nozzle. A single pump can easily operate two nozzles, each with independent controls. Simply purchase an additional nozzle adaptor and add one more hydraulic hose to the water outlet. The Wetblast Injector System requires no electric power, so there are no wires and no connections to short or shock. Because the Wetblast Injector has its own pump and uses relatively small amounts of water, any source of clean water will work — household tap, water tower, or low-lying tank. A regulator and pressure gauge, mounted inside the control box, controls water pressure. The operator adjusts the water volume with a fine-thread needle valve at the nozzle. The versatile Wetblast Injector lets the operator blast with wet or dry abrasive. When the machine is equipped with an abrasive cut-off system, the operator can rinse the surface with air and water, then dry the surface with high-pressure air. Applications A blast system with Clemco’s Wetblast Injector quickly cleans structural steel to any degree of cleanliness from brush-off to white metal. After blasting, the water-and-air rinse removes soluble salts and other corrosives that can cling to the surface. If flash rust is a problem, the pump can siphon clean water from a static-holding tank that contains a premixed rust inhibitor solution to retard rust development on exposed steel.