Meyer Hydraulics

Twelve (12) optional 1.75" (44mm) solid steel powder-coated Extension Bars of various lengths screw into the top of an A600 or A700 Aircraft Jack's Inner Slide Tube or into the AT500-CA Conversion Adapter used on the A500 Series. They extend the height of the Jack 1.5" to 12.5" (38 to 318mm) in 1" (25mm) increments. Both of the AT-JPRn Jacking Point Receivers or a top-of-the-jack aircraft weighing Load Cell can quickly be put into the top non-threaded hole of an AT-EBnnn Extension Bar. The AT-EBnnn's cannot be used on the A755C and A760A Aircraft Jacks. AT-EB015 thru AT-EB125 Extension Bars Extends the height of the TriTask Jack so technicians can get close to the airplane or helicopter without wasting valuable hydraulic lifting stroke.

Made of solid steel and powder-coated with a long-lasting yellow finish for easy spotting, these JPR Receivers have been designed to be put into the top of an A600 or A700 Series Aircraft Jack's Inner Slide Tube, an AT-EBnnn Extension Bar or the AT500-CA Conversion Adapter for the A500 Series. The AT-JPR1 is a 1.5" x .187" (38x5mm) pad with a .875" (22mm) round Jacking Point receiving socket. The AT-JPR2 is a little larger with a 1.75" x .375" (44x10mm) pad with a 1.25" (32mm) round receiving socket. Both have a 1" x 1" (25.25mm) round stem.

• SeriesAT500

This optional 2.25" (57mm) round steel powder-coated Adapter only connects to the A500 Series Inner Slide Tubes and adds .875" (22mm) to the height of the Jack. After securing the Adapter to the Inner Slide Tube's protruding anchoring stud, an AT-JPRn, AT-EBnnn or a top-of-the-jack aircraft weighing Load Cell can be quickly put into the top of the Conversion Adapter. Mounting the AT500-CA Conversion Adapter to an A500 Inner Slide Tube

The new TRITASK Aircraft Jacks with their powder-coated Inner Slide Tubes form the "anchor" of the new TriTask System. leftThe top of the A600 and A700 Series Inner Slide Tubes are designed to receive an AT-JPRn, AT-EBnnn or a top-of-the-jack aircraft weighing Load Cell. leftThe Inner Slide Tubes for the A500 Series have a built-in 1.25" (32mm) round Jacking Point receiving socket machined into the top of its protruding anchoring stud.The AT500-CA Conversion Adapter can be mounted on the anchoring stud, which will then allow the A500 Series Inner Slide Tubes to function the same as the A600 and A700 Series Inner Slide Tubes. left Top portion of A600 and A700 Series Inner Slide Tube left Top portion of A500 Series Inner Slide Tube

Built-in Ability to use a Top-of-the-jack Helicopter and Airplane Weighing Load Cell A Load Cell with the standard 1" x 1" (25x25mm) round stem can be quickly put into the top of an A600 or A700 Series Aircraft Jack's Inner Slide Tube, an AT-EBnnn Extension Bar or the top of an AT500-CA Conversion Adapter used on the A500 Series. Meyer Hydraulics does not make or distribute aircraft weighing Load Cells or Scales. These are readily available from other sources, such as one of our Select Distributors or Jackson Aircraft Weighing Scales. left A500 Inner Slide Tube with AT500-CA Conversion Adapter, AT-EB025 Extension Bar and Load Cell left Mounting Load Cell in an A600 or A700 Series Inner Slide Tube

The SRC Rotary Crane was designed to pivot in an upper and lower anchor. For use with a Service Van, the anchors are mounted to the floor and ceiling of the Van allowing the SRC Rotary Crane to pivot out of the back of the Service Van. The service technician can arc its boom over heavy loads, such as riding mowers, and easily lift either end for servicing blades, belts etc. For industrial applications the SRC can be mounted to any fixed structure for a variety of uses, such as workpiece handling in Machining Centers, Lathes and Milling Machines, putting items into dip tanks or assisting in repair or assembly. Features • Interchangeable Standard Pump • Pump handle positioned to allow the operator to operate the hydraulics while guiding the load • Deep reaching boom • Rugged Construction... Post made with 2.375" OD heavy wall tubing 49" long • Capacity up to 800 lbs.